Lamar Owen wrote:
> On 11/04/2015 04:48 PM, m.roth@xxxxxxxxx wrote:
>> Yep. They got nothing for CentOS 7. Btw, we got him the full width by
>> changing the cable, from DVI-I to DVI-D (dual link). Then he had to
>> change it back to not recognizing the full width of the screen via the
>> control ctr, because when it did, everything was distorted - circles
>> were ovals, etc. I suppose I'll get around to writing him a xorg.conf
>> at some time.
>
> Mark, with the FirePro V3900 the 'radeon' driver should be loading, not
> the VESA one. Is xorg-x11-drv-ati installed? I am running a FirePro
Yup:
rpm -qa | grep drv-ati
xorg-x11-drv-ati-7.4.0-1.20140918git56c7fb8.el7.x86_64
Note that, as I said earlier, it is over a year old.
> M7820 in my Dell Precision M6500, and everything 'Just Works' with the
> xorg-x11-drv-ati package (and its dependencies) installed. I even get
> triple monitor support at 1920x1200 while docked, using the dual
> DisplayPort outputs on the dock, on two 24" Dell monitors plus the
> M6500's 17" display. For using a projector, the DisplayPort connector
> on the laptop works fine, even hotplug works. I have been very pleased
This is, according to what I google, a 27", and it's black for what could
well be 1.5" on either side... which makes it 24"....
<snip>
> For my FirePro M7820, here's the lspci output:
> 01:00.0 VGA compatible controller: Advanced Micro Devices, Inc.
> [AMD/ATI] Broadway XT [Mobility Radeon HD 5870]
> 01:00.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Juniper
> HDMI Audio [Radeon HD 5700 Series]
>
02:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI]
Turks GL [FirePro V3900]
02:00.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI]
Turks/Whistler HDMI Audio [Radeon HD 6000 Series]
> Are you sure you're actually using the VESA drivers? The Turks chip
> used in the V3900 shows as being supported ('man radeon' will give you a
> list of supported chips).
>
> Check /var/log/Xorg.0.log and see what's going on.
Did. I am *not* going to paste in almost 3,000 lines (what a *useful*
logfile... NOT!), but the relevant lines, I believe, are
[ 18.760] (EE) open /dev/fb0: No such file or directory
[ 18.760] (WW) Falling back to old probe method for fbdev
[ 18.760] (II) Loading sub module "fbdevhw"
[ 18.760] (II) LoadModule: "fbdevhw"
[ 18.760] (II) Loading /usr/lib64/xorg/modules/libfbdevhw.so
[ 18.760] (II) Module fbdevhw: vendor="X.Org Foundation"
[ 18.760] compiled for 1.15.0, module version = 0.0.2
[ 18.760] ABI class: X.Org Video Driver, version 15.0
[ 18.760] (EE) open /dev/fb0: No such file or directory
[ 18.760] (EE) Screen 0 deleted because of no matching config section.
[ 18.760] (II) UnloadModule: "radeon"
[ 18.760] (EE) Screen 0 deleted because of no matching config section.
[ 18.760] (II) UnloadModule: "modesetting"
[ 18.760] (EE) Screen 0 deleted because of no matching config section.
[ 18.760] (II) UnloadModule: "fbdev"
[ 18.760] (II) UnloadSubModule: "fbdevhw"
[ 18.760] (II) Loading sub module "vbe"
[ 18.760] (II) LoadModule: "vbe"
[ 18.760] (II) Loading /usr/lib64/xorg/modules/libvbe.so
[ 18.803] (II) Module vbe: vendor="X.Org Foundation"
[ 18.803] compiled for 1.15.0, module version = 1.1.0
[ 18.803] ABI class: X.Org Video Driver, version 15.0
[ 18.803] (II) Loading sub module "int10"
[ 18.803] (II) LoadModule: "int10"
[ 18.803] (II) Loading /usr/lib64/xorg/modules/libint10.so
[ 18.805] (II) Module int10: vendor="X.Org Foundation"
[ 18.805] compiled for 1.15.0, module version = 1.0.0
[ 18.805] ABI class: X.Org Video Driver, version 15.0
[ 18.805] (II) VESA(0): initializing int10
[ 18.806] (II) VESA(0): Primary V_BIOS segment is: 0xc000
[ 18.806] (II) VESA(0): VESA BIOS detected
Followed by many, many lines that begin with VESA.
That's why I said that at some point I was going to hand-craft an
xorg.conf. Do you know if there's a way to dump the current settings to a
file? I know I can do it with NVidia, but this is just KDE's settings.
>
> Wolfy is working on the latest Catalyst drivers for ELrepo for EL7
> (fglrx 15.9 as I recall). There are some challenges, and the kmod-fglrx
> package is still in testing. But as well as the open radeon driver is
> supporting my M7820 I'm not sure I want to change at this point. There
> would have to be some compelling reason.
Thanks for the info - I'm looking forward to that.
mark
_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
https://lists.centos.org/mailman/listinfo/centos
