On 09/17/2012 01:04 PM, Jerry Geis wrote:
> On 09/17/2012 01:04 PM, Jerry Geis wrote:
>>> Because of the information in a previous message, I think you have a
>>> separate partition for /boot. Is that the case and, if so, did you
>>> consider section 5.1 of the Grub Installation information?
>>>
>>> (For what it's worth, I don't recommend having a separate partition
>>> for /boot.)
>>>
>>> Also, vmlinuz-2.6.32.59 doesn't look right; I think it should be
>>> vmlinuz-2.6.32.59.el6 or so.
>>>
>>> I guess I should ask you to post /boot/grub/grub.conf and /etc/fstab,
>>> and the outpout of "df" and "ls -l /boot".
>> No I have one partition in this case.
>> /dev/sda1 is everything
>> /dev/sda2 is swap
>>
>>
> I sent that by accident I was still getting the other files.
>
> Jerry
-rw-r--r--. 1 root root 106611 Jun 22 07:23 config-2.6.32-279.el6.i686
drwxr-xr-x. 3 root root 4096 Sep 13 16:03 efi
drwxr-xr-x. 2 root root 4096 Sep 16 21:29 grub
-rw-r--r--. 1 root root 14689286 Sep 13 16:05
initramfs-2.6.32-279.el6.i686.img
-rw-r--r-- 1 root root 9580046 Sep 14 09:24 initramfs-2.6.32.59.img
-rw-------. 1 root root 3573935 Sep 13 16:09
initrd-2.6.32-279.el6.i686kdump.img
-rw-r--r--. 1 root root 175903 Jun 22 07:24 symvers-2.6.32-279.el6.i686.gz
lrwxrwxrwx 1 root root 26 Sep 14 09:24 System.map ->
/boot/System.map-2.6.32.59
-rw-r--r--. 1 root root 1846041 Jun 22 07:23 System.map-2.6.32-279.el6.i686
-rw-r--r-- 1 root root 1660822 Sep 14 09:24 System.map-2.6.32.59
lrwxrwxrwx 1 root root 23 Sep 14 09:24 vmlinuz ->
/boot/vmlinuz-2.6.32.59
-rwxr-xr-x. 1 root root 3856608 Jun 22 07:23 vmlinuz-2.6.32-279.el6.i686
-rw-r--r-- 1 root root 3443520 Sep 14 09:24 vmlinuz-2.6.32.59
I cannot do "df" as currently there is no command as the file system is
not mounted.
I have built 2.6.32.59 as I needed to run the kernel without PAE.
I extracted the kernel on a KVM image, I did
cp /boot/config-2.6.32-279.el6.i686 .config
make oldconfig
make menuconfig
went to HIGH MEMORY Support and changed to 4GB.
did the make bzImage, make modules, make modules_install, make install
That's where I get the 2.6.32.59...
When booting the KVM image with the kernel I built it works fine.
I can even make the CF card look like a USB drive and boot it and it
works fine.
Its just when I go native CF in the device it says no root file system.
I have centos 5.X CF cards working just fine on my end target, I'm just
trying to get 6.X to run.
I'm sure its something small I am missing. I just havent found it.
Thanks,
jerry
_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
http://lists.centos.org/mailman/listinfo/centos
