Hum, if I decide to use software RAID (the dark and easy way) I can use my
standard onboard IDE controller instead of the Promise card...Actually I
wonder what the difference is between a full-software solutiuon like the one
provided by the linux kernel and a semi-hardware solution like the
Promise...
As far as I know the only benefit of a semi-hardware solution is to "share"
the workload between the CPU and a RAID chip but you need a nasty driver to
do that...
----- Original Message -----
From: "William Warren" <hescominsoon@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx>
To: "CentOS mailing list" <centos@xxxxxxxxxx>
Sent: Saturday, May 21, 2005 3:16 PM
Subject: Re: Promise FastTrak series
> Well promise RAID is software raid as well. Using the included 2.6xx raid
> functionality will at least not hurt your performance anymore than using
> the Promise software raid drivers. Depending on the nature of Promise's
> drivers(which i have heard mainly negative things) you will get better
> performance using the built in RAID from Linux.
>
> Steven Moix - Axianet.ch wrote:
>> Hello,
>>
>> In some weeks I'm going to reinstall some old RedHat9 based servers with
>> Promise FastTrak TX2000 "semi-hardware" RAID1 controllers. I just tried
>> to install CentOS 4.0 on a computer with a spare card and as usual both
>> HDD attached to the RAID1 controller are seen separately by the installer
>> because the specific driver for the TX2000 wasn't loaded. Nothing new
>> here, it was always like this on every distro as far as I know.
>>
>> Now I googeled a bit and have some questions:
>>
>> 1. In some forums I could read that the FastTrak series in RAID mode
>> wasn't supported anymore in the 2.6 kernel (was PDCRAID module in the
>> later 2.4 kernels).
>> Quoted apparently from the linux kernel mailing list:
>>
>>>> In 2.6, Promise software RAID support does not exist. In conversations
>>>> with Promise, we all agreed to encourage and support the standard Linux
>>>> RAID, md.
>>
>> So does this mean that I have to use software RAID in linux if I don't
>> want to load the drivers provided by Promise (see question 2)?
>>
>> 2. On the other hand Promise provides the partial source code for their
>> driver, but there is a silly problem with this...I want to install my OS
>> directly on the RAID array :)
>> So I guess that I would have to:
>> - Install CentOS on another computer, compile the driver provided by
>> Promise, make a driver disk (don't ask me how).
>> - Boot CentOS on the server with the controller and type "linux dd" to
>> load this driver disk.
>> - Pray and correct bugs for the next 2 weeks.
>> Is this the right way to go?
>>
>> Any feedback with FastTrak TX2000 or TX4000 controllers would be very
>> welcome, let me know which solution you choosed.
>>
>> Thanks
>> Steven
>>
>> _______________________________________________
>> CentOS mailing list
>> CentOS@xxxxxxxxxx
>> http://lists.centos.org/mailman/listinfo/centos
>>
>
> --
> Computer House Calls, Networks, Security, Web Design:
> http://www.emmanuelcomputerconsulting.com
> What businesses are in Brunswick, Maryland? Check Brunswick First!
> http://www.checkbrunswickfirst.com
> My "Foundation" verse:
> Isa 54:17 No weapon that is formed against thee shall prosper; and every
> tongue that shall rise against thee in judgment thou shalt condemn. This
> is the heritage of the servants of the LORD, and their righteousness is of
> me, saith the LORD.
>
> -- carpe ductum -- "Grab the tape"
> CDTT (Certified Duct Tape Technician)
>
> Linux user #322099
> Machines:
> 206822
> 256638
> 276825
> http://counter.li.org/
> _______________________________________________
> CentOS mailing list
> CentOS@xxxxxxxxxx
> http://lists.centos.org/mailman/listinfo/centos
>
