On Sat, Jan 21, 2023 at 04:55:21PM +0800, Jason Xing wrote:
> From: Jason Xing <kernelxing@xxxxxxxxxxx>
>
> I encountered one case where I cannot increase the MTU size with XDP
> enabled if the server is equipped with IXGBE card, which happened on
> thousands of servers. I noticed it was prohibited from 2017[1] and
> added size checks[2] if allowed soon after the previous patch.
>
> Interesting part goes like this:
> 1) Changing MTU directly from 1500 (default value) to 2000 doesn't
> work because the driver finds out that 'new_frame_size >
> ixgbe_rx_bufsz(ring)' in ixgbe_change_mtu() function.
> 2) However, if we change MTU to 1501 then change from 1501 to 2000, it
> does work, because the driver sets __IXGBE_RX_3K_BUFFER when MTU size
> is converted to 1501, which later size check policy allows.
>
> The default MTU value for most servers is 1500 which cannot be adjusted
> directly to the value larger than IXGBE_MAX_2K_FRAME_BUILD_SKB (1534 or
> 1536) if it loads XDP.
>
> After I do a quick study on the manner of i40E driver allowing two kinds
> of buffer size (one is 2048 while another is 3072) to support XDP mode in
> i40e_max_xdp_frame_size(), I believe the default MTU size is possibly not
> satisfied in XDP mode when IXGBE driver is in use, we sometimes need to
> insert a new header, say, vxlan header. So setting the 3K-buffer flag
> could solve the issue.
>
> [1] commit 38b7e7f8ae82 ("ixgbe: Do not allow LRO or MTU change with XDP")
> [2] commit fabf1bce103a ("ixgbe: Prevent unsupported configurations with
> XDP")
>
> Signed-off-by: Jason Xing <kernelxing@xxxxxxxxxxx>
> ---
> drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 3 +++
> 1 file changed, 3 insertions(+)
>
> diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
> index ab8370c413f3..dc016582f91e 100644
> --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
> +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
> @@ -4313,6 +4313,9 @@ static void ixgbe_set_rx_buffer_len(struct ixgbe_adapter *adapter)
> if (IXGBE_2K_TOO_SMALL_WITH_PADDING ||
> (max_frame > (ETH_FRAME_LEN + ETH_FCS_LEN)))
> set_bit(__IXGBE_RX_3K_BUFFER, &rx_ring->state);
> +
> + if (ixgbe_enabled_xdp_adapter(adapter))
> + set_bit(__IXGBE_RX_3K_BUFFER, &rx_ring->state);
This will result with unnecessary overhead for 1500 MTU because you will
be working on order-1 pages. Instead I would focus on fixing
ixgbe_change_mtu() and stop relying on ixgbe_rx_bufsz() in there. You can
check what we do on ice/i40e sides.
I'm not looking actively into ixgbe internals but I don't think that there
is anything that stops us from using 3k buffers with XDP.
> #endif
> }
> }
> --
> 2.37.3
>
