> On 31 Dec 2022, at 12:55 AM, Alexei Starovoitov <alexei.starovoitov@xxxxxxxxx> wrote:
>
> On Fri, Dec 30, 2022 at 1:54 AM Hao Sun <sunhao.th@xxxxxxxxx> wrote:
>>
>>
>>
>>> On 28 Dec 2022, at 2:35 PM, Yonghong Song <yhs@xxxxxxxx> wrote:
>>>
>>>
>>>
>>> On 12/21/22 8:35 PM, Hao Sun wrote:
>>>> Hi,
>>>> This crash can be triggered by executing the C reproducer for
>>>> multiple times, which just keep loading the following prog as
>>>> raw tracepoint into kmem_cache_free().
>>>> The prog send SIGSEGV to current via bpf_send_signal_thread(),
>>>> after load this, whoever tries to free mem would trigger this,
>>>> kernel crashed when this happens to init.
>>>> Seems we should filter init out in bpf_send_signal_common() by
>>>> is_global_init(current), or maybe we should check this in the
>>>> verifier?
>>>
>>> The helper is just to send a particular signal to *current*
>>> thread. In typical use case, it is never a good idea to send
>>> the signal to a *random* thread. In certain cases, maybe user
>>> indeed wants to send the signal to init thread to observe
>>> something. Note that such destructive side effect already
>>> exists in the bpf land. For example, for a xdp program,
>>> it could drop all packets to make machine not responsive
>>> to ssh etc. Therefore, I recommend to keep the existing
>>> bpf_send_signal_common() helper behavior.
>>
>> Sound the two are different cases. Not responsive in XDP seems like
>> an intended behaviour, panic caused by killing init is buggy. If the
>> last thread of global init was killed, kernel panic immediately.
>
> I don't get it. How was it possible that this prog was
> executed with current == pid 1 ?
The prog is raw trace point and is attached to ‘kmem_cache_free’ event.
When init triggered the event, the prog would be executed with pid 1.
But, the reason of this crash is not very clear to me, because it’s
really hard to debug with original C reproducer.
The following is the corresponding Syz prog:
# {Threaded:true Repeat:true RepeatTimes:0 Procs:1 Slowdown:1 Sandbox:none SandboxArg:0 Leak:false NetInjection:true NetDevices:true NetReset:true Cgroups:true BinfmtMisc:true CloseFDs:true KCSAN:false DevlinkPCI:false NicVF:false USB:false VhciInjection:false Wifi:false IEEE802154:true Sysctl:true UseTmpDir:true HandleSegv:true Repro:false Trace:false LegacyOptions:{Collide:false Fault:false FaultCall:0 FaultNth:0}}
r0 = bpf$BPF_PROG_RAW_TRACEPOINT_LOAD(0x5, &(0x7f0000000000)={0x11, 0xe, &(0x7f0000000400)=ANY=[@ANYBLOB="18000000000000000000000000000000180600000000000000000000000000001807000000000000000000000000000018080000000000000000000000000000180900000000000000000000000000002d00020000000000b70100000b000000850000007500000095"], &(0x7f00000000c0)}, 0x80)
bpf$BPF_RAW_TRACEPOINT_OPEN(0x11, &(0x7f0000000100)={&(0x7f0000000080)='kmem_cache_free\x00', r0}, 0x10)
