Basic DSA driver support for lan937x and the device will be configured through SPI interface. drivers/net/dsa/microchip/ path is already part of MAINTAINERS & the new files come under this path. Hence no update needed to the MAINTAINERS Reused KSZ APIs for port_bridge_join() & port_bridge_leave() and added support for port_stp_state_set(). RGMII internal delay values for the mac is retrieved from rx-internal-delay-ps & tx-internal-delay-ps as per the feedback from v3 patch series. https://lore.kernel.org/netdev/20210802121550.gqgbipqdvp5x76ii@skbuf/ It supports standard delay 2ns only. If the property is not found, the value will be forced to 0. Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@xxxxxxxxxxxxx> Signed-off-by: Arun Ramadoss <arun.ramadoss@xxxxxxxxxxxxx> --- drivers/net/dsa/microchip/Kconfig | 12 + drivers/net/dsa/microchip/Makefile | 4 + drivers/net/dsa/microchip/ksz_common.h | 5 + drivers/net/dsa/microchip/lan937x_dev.c | 251 +++++++++ drivers/net/dsa/microchip/lan937x_dev.h | 36 ++ drivers/net/dsa/microchip/lan937x_main.c | 216 +++++++ drivers/net/dsa/microchip/lan937x_reg.h | 688 +++++++++++++++++++++++ 7 files changed, 1212 insertions(+) create mode 100644 drivers/net/dsa/microchip/lan937x_dev.c create mode 100644 drivers/net/dsa/microchip/lan937x_dev.h create mode 100644 drivers/net/dsa/microchip/lan937x_main.c create mode 100644 drivers/net/dsa/microchip/lan937x_reg.h diff --git a/drivers/net/dsa/microchip/Kconfig b/drivers/net/dsa/microchip/Kconfig index c9e2a8989556..f329cca934ee 100644 --- a/drivers/net/dsa/microchip/Kconfig +++ b/drivers/net/dsa/microchip/Kconfig @@ -3,6 +3,18 @@ config NET_DSA_MICROCHIP_KSZ_COMMON select NET_DSA_TAG_KSZ tristate +config NET_DSA_MICROCHIP_LAN937X + tristate "Microchip LAN937X series SPI connected switch support" + depends on NET_DSA && SPI + select NET_DSA_MICROCHIP_KSZ_COMMON + select REGMAP_SPI + help + This driver adds support for Microchip LAN937X series + switch chips. + + Select to enable support for registering switches configured + through SPI. + menuconfig NET_DSA_MICROCHIP_KSZ9477 tristate "Microchip KSZ9477 series switch support" depends on NET_DSA diff --git a/drivers/net/dsa/microchip/Makefile b/drivers/net/dsa/microchip/Makefile index 2a03b21a3386..d32ff38dc240 100644 --- a/drivers/net/dsa/microchip/Makefile +++ b/drivers/net/dsa/microchip/Makefile @@ -6,3 +6,7 @@ obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ9477_SPI) += ksz9477_spi.o obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ8795) += ksz8795.o obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ8795_SPI) += ksz8795_spi.o obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ8863_SMI) += ksz8863_smi.o + +obj-$(CONFIG_NET_DSA_MICROCHIP_LAN937X) += lan937x.o +lan937x-objs := lan937x_dev.o +lan937x-objs += lan937x_main.o diff --git a/drivers/net/dsa/microchip/ksz_common.h b/drivers/net/dsa/microchip/ksz_common.h index 28cda79b090f..ebbeb025c468 100644 --- a/drivers/net/dsa/microchip/ksz_common.h +++ b/drivers/net/dsa/microchip/ksz_common.h @@ -42,6 +42,8 @@ struct ksz_port { struct ksz_port_mib mib; phy_interface_t interface; u16 max_frame; + u32 rgmii_tx_val; + u32 rgmii_rx_val; }; struct ksz_device { @@ -148,6 +150,9 @@ void ksz_switch_remove(struct ksz_device *dev); int ksz8_switch_register(struct ksz_device *dev); int ksz9477_switch_register(struct ksz_device *dev); +int lan937x_switch_register(struct ksz_device *dev); + +int lan937x_check_device_id(struct ksz_device *dev); void ksz_update_port_member(struct ksz_device *dev, int port); void ksz_init_mib_timer(struct ksz_device *dev); diff --git a/drivers/net/dsa/microchip/lan937x_dev.c b/drivers/net/dsa/microchip/lan937x_dev.c new file mode 100644 index 000000000000..c6bd8fac735d --- /dev/null +++ b/drivers/net/dsa/microchip/lan937x_dev.c @@ -0,0 +1,251 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Microchip lan937x dev ops functions + * Copyright (C) 2019-2021 Microchip Technology Inc. + */ +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/iopoll.h> +#include <linux/of_mdio.h> +#include <linux/platform_data/microchip-ksz.h> +#include <linux/phy.h> +#include <linux/if_bridge.h> +#include <net/dsa.h> +#include <net/switchdev.h> + +#include "lan937x_reg.h" +#include "ksz_common.h" +#include "lan937x_dev.h" + +int lan937x_cfg(struct ksz_device *dev, u32 addr, u8 bits, bool set) +{ + return regmap_update_bits(dev->regmap[0], addr, bits, set ? bits : 0); +} + +int lan937x_port_cfg(struct ksz_device *dev, int port, int offset, u8 bits, + bool set) +{ + return regmap_update_bits(dev->regmap[0], PORT_CTRL_ADDR(port, offset), + bits, set ? bits : 0); +} + +int lan937x_pread8(struct ksz_device *dev, int port, int offset, u8 *data) +{ + return ksz_read8(dev, PORT_CTRL_ADDR(port, offset), data); +} + +int lan937x_pread16(struct ksz_device *dev, int port, int offset, u16 *data) +{ + return ksz_read16(dev, PORT_CTRL_ADDR(port, offset), data); +} + +int lan937x_pread32(struct ksz_device *dev, int port, int offset, u32 *data) +{ + return ksz_read32(dev, PORT_CTRL_ADDR(port, offset), data); +} + +int lan937x_pwrite8(struct ksz_device *dev, int port, int offset, u8 data) +{ + return ksz_write8(dev, PORT_CTRL_ADDR(port, offset), data); +} + +int lan937x_pwrite16(struct ksz_device *dev, int port, int offset, u16 data) +{ + return ksz_write16(dev, PORT_CTRL_ADDR(port, offset), data); +} + +int lan937x_pwrite32(struct ksz_device *dev, int port, int offset, u32 data) +{ + return ksz_write32(dev, PORT_CTRL_ADDR(port, offset), data); +} + +void lan937x_cfg_port_member(struct ksz_device *dev, int port, u8 member) +{ + lan937x_pwrite32(dev, port, REG_PORT_VLAN_MEMBERSHIP__4, member); +} + +int lan937x_reset_switch(struct ksz_device *dev) +{ + u32 data32; + u8 data8; + int ret; + + /* reset switch */ + ret = lan937x_cfg(dev, REG_SW_OPERATION, SW_RESET, true); + if (ret < 0) + return ret; + + ret = ksz_read8(dev, REG_SW_LUE_CTRL_1, &data8); + if (ret < 0) + return ret; + + /* Enable Auto Aging */ + ret = ksz_write8(dev, REG_SW_LUE_CTRL_1, data8 | SW_LINK_AUTO_AGING); + if (ret < 0) + return ret; + + /* disable interrupts */ + ret = ksz_write32(dev, REG_SW_INT_MASK__4, SWITCH_INT_MASK); + if (ret < 0) + return ret; + + ret = ksz_write32(dev, REG_SW_PORT_INT_MASK__4, 0xFF); + if (ret < 0) + return ret; + + return ksz_read32(dev, REG_SW_PORT_INT_STATUS__4, &data32); +} + +static int lan937x_switch_detect(struct ksz_device *dev) +{ + u32 id32; + int ret; + + /* Read Chip ID */ + ret = ksz_read32(dev, REG_CHIP_ID0__1, &id32); + if (ret < 0) + return ret; + + if (id32 != 0 && id32 != 0xffffffff) { + dev->chip_id = id32; + dev_info(dev->dev, "Chip ID: 0x%x", id32); + ret = 0; + } else { + ret = -EINVAL; + } + + return ret; +} + +static void lan937x_switch_exit(struct ksz_device *dev) +{ + lan937x_reset_switch(dev); +} + +static u32 lan937x_get_port_addr(int port, int offset) +{ + return PORT_CTRL_ADDR(port, offset); +} + +bool lan937x_is_internal_phy_port(struct ksz_device *dev, int port) +{ + /* Check if the port is RGMII */ + if (port == LAN937X_RGMII_1_PORT || port == LAN937X_RGMII_2_PORT) + return false; + + /* Check if the port is SGMII */ + if (port == LAN937X_SGMII_PORT && + GET_CHIP_ID_LSB(dev->chip_id) == CHIP_ID_73) + return false; + + return true; +} + +bool lan937x_is_rgmii_port(struct ksz_device *dev, int port) +{ + /* Check if the port is RGMII */ + if (port == LAN937X_RGMII_1_PORT || port == LAN937X_RGMII_2_PORT) + return true; + + return false; +} + +bool lan937x_is_internal_base_tx_phy_port(struct ksz_device *dev, int port) +{ + /* Check if the port is internal tx phy port */ + if (lan937x_is_internal_phy_port(dev, port) && + port == LAN937X_TXPHY_PORT) + if ((GET_CHIP_ID_LSB(dev->chip_id) == CHIP_ID_71) || + (GET_CHIP_ID_LSB(dev->chip_id) == CHIP_ID_72)) + return true; + + return false; +} + +bool lan937x_is_internal_base_t1_phy_port(struct ksz_device *dev, int port) +{ + /* Check if the port is internal t1 phy port */ + if (lan937x_is_internal_phy_port(dev, port) && + !lan937x_is_internal_base_tx_phy_port(dev, port)) + return true; + + return false; +} + +void lan937x_port_setup(struct ksz_device *dev, int port, bool cpu_port) +{ + struct dsa_switch *ds = dev->ds; + u8 member; + + /* enable tag tail for host port */ + if (cpu_port) + lan937x_port_cfg(dev, port, REG_PORT_CTRL_0, + PORT_TAIL_TAG_ENABLE, true); + + /* disable frame check length field */ + lan937x_port_cfg(dev, port, REG_PORT_MAC_CTRL_0, PORT_FR_CHK_LENGTH, + false); + + /* set back pressure for half duplex */ + lan937x_port_cfg(dev, port, REG_PORT_MAC_CTRL_1, PORT_BACK_PRESSURE, + true); + + /* enable 802.1p priority */ + lan937x_port_cfg(dev, port, P_PRIO_CTRL, PORT_802_1P_PRIO_ENABLE, true); + + if (!lan937x_is_internal_phy_port(dev, port)) + lan937x_port_cfg(dev, port, REG_PORT_XMII_CTRL_0, + PORT_TX_FLOW_CTRL | PORT_RX_FLOW_CTRL, + true); + + if (cpu_port) + member = dsa_user_ports(ds); + else + member = BIT(dsa_upstream_port(ds, port)); + + lan937x_cfg_port_member(dev, port, member); +} + +static int lan937x_switch_init(struct ksz_device *dev) +{ + int ret; + + dev->ds->ops = &lan937x_switch_ops; + + /* Check device tree */ + ret = lan937x_check_device_id(dev); + if (ret < 0) + return ret; + + dev->port_mask = (1 << dev->port_cnt) - 1; + + dev->ports = devm_kzalloc(dev->dev, + dev->port_cnt * sizeof(struct ksz_port), + GFP_KERNEL); + if (!dev->ports) + return -ENOMEM; + + /* set the real number of ports */ + dev->ds->num_ports = dev->port_cnt; + return 0; +} + +static int lan937x_init(struct ksz_device *dev) +{ + int ret; + + ret = lan937x_switch_init(dev); + if (ret < 0) + dev_err(dev->dev, "failed to initialize the switch"); + + return ret; +} + +const struct ksz_dev_ops lan937x_dev_ops = { + .get_port_addr = lan937x_get_port_addr, + .cfg_port_member = lan937x_cfg_port_member, + .port_setup = lan937x_port_setup, + .shutdown = lan937x_reset_switch, + .detect = lan937x_switch_detect, + .init = lan937x_init, + .exit = lan937x_switch_exit, +}; diff --git a/drivers/net/dsa/microchip/lan937x_dev.h b/drivers/net/dsa/microchip/lan937x_dev.h new file mode 100644 index 000000000000..21f4aade0199 --- /dev/null +++ b/drivers/net/dsa/microchip/lan937x_dev.h @@ -0,0 +1,36 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* Microchip lan937x dev ops headers + * Copyright (C) 2019-2021 Microchip Technology Inc. + */ + +#ifndef __LAN937X_CFG_H +#define __LAN937X_CFG_H + +int lan937x_cfg(struct ksz_device *dev, u32 addr, u8 bits, bool set); +int lan937x_port_cfg(struct ksz_device *dev, int port, int offset, + u8 bits, bool set); +int lan937x_pread8(struct ksz_device *dev, int port, int offset, + u8 *data); +int lan937x_pread16(struct ksz_device *dev, int port, int offset, + u16 *data); +int lan937x_pread32(struct ksz_device *dev, int port, int offset, + u32 *data); +int lan937x_pwrite8(struct ksz_device *dev, int port, + int offset, u8 data); +int lan937x_pwrite16(struct ksz_device *dev, int port, + int offset, u16 data); +int lan937x_pwrite32(struct ksz_device *dev, int port, + int offset, u32 data); +bool lan937x_is_internal_phy_port(struct ksz_device *dev, int port); +bool lan937x_is_internal_base_tx_phy_port(struct ksz_device *dev, int port); +bool lan937x_is_internal_base_t1_phy_port(struct ksz_device *dev, int port); +bool lan937x_is_rgmii_port(struct ksz_device *dev, int port); +int lan937x_reset_switch(struct ksz_device *dev); +void lan937x_cfg_port_member(struct ksz_device *dev, int port, + u8 member); +void lan937x_port_setup(struct ksz_device *dev, int port, bool cpu_port); + +extern const struct dsa_switch_ops lan937x_switch_ops; +extern const struct ksz_dev_ops lan937x_dev_ops; + +#endif diff --git a/drivers/net/dsa/microchip/lan937x_main.c b/drivers/net/dsa/microchip/lan937x_main.c new file mode 100644 index 000000000000..154d7a0f08ac --- /dev/null +++ b/drivers/net/dsa/microchip/lan937x_main.c @@ -0,0 +1,216 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Microchip LAN937X switch driver main logic + * Copyright (C) 2019-2021 Microchip Technology Inc. + */ +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/iopoll.h> +#include <linux/phy.h> +#include <linux/of_net.h> +#include <linux/if_bridge.h> +#include <linux/math.h> +#include <net/dsa.h> +#include <net/switchdev.h> + +#include "lan937x_reg.h" +#include "ksz_common.h" +#include "lan937x_dev.h" + +static enum dsa_tag_protocol lan937x_get_tag_protocol(struct dsa_switch *ds, + int port, + enum dsa_tag_protocol mp) +{ + return DSA_TAG_PROTO_LAN937X_VALUE; +} + +static void lan937x_port_stp_state_set(struct dsa_switch *ds, int port, + u8 state) +{ + ksz_port_stp_state_set(ds, port, state, P_STP_CTRL); +} + +static void lan937x_config_cpu_port(struct dsa_switch *ds) +{ + struct ksz_device *dev = ds->priv; + int i; + + ds->num_ports = dev->port_cnt; + + for (i = 0; i < dev->port_cnt; i++) { + if (dsa_is_cpu_port(ds, i) && (dev->cpu_ports & (1 << i))) { + dev->cpu_port = i; + + /* enable cpu port */ + lan937x_port_setup(dev, i, true); + } + } + + for (i = 0; i < dev->port_cnt; i++) { + if (i == dev->cpu_port) + continue; + + lan937x_port_stp_state_set(ds, i, BR_STATE_DISABLED); + } +} + +static int lan937x_set_rgmii_delay(struct ksz_device *dev, int port, + u32 val, bool is_tx) +{ + struct ksz_port *p = &dev->ports[port]; + const char *name[2] = { "rx", "tx" }; + + /* alert if delay is out of range */ + if (val != 0 && val != 2000) { + dev_err(dev->dev, + "rgmii %s delay %d is out of range for the port %d\n", + name[is_tx], val, port); + return -EOPNOTSUPP; + } + + /* get the valid value & store it for delay calculation */ + if (is_tx) + p->rgmii_tx_val = val; + else + p->rgmii_rx_val = val; + + return 0; +} + +static int lan937x_parse_dt_rgmii_delay(struct ksz_device *dev) +{ + struct device_node *ports, *port; + int err, p; + u32 val; + + ports = of_get_child_by_name(dev->dev->of_node, "ports"); + if (!ports) + ports = of_get_child_by_name(dev->dev->of_node, + "ethernet-ports"); + if (!ports) { + dev_err(dev->dev, "no ports child node found\n"); + return -EINVAL; + } + + for_each_available_child_of_node(ports, port) { + err = of_property_read_u32(port, "reg", &p); + if (err) { + dev_err(dev->dev, "Port num not defined in the DT, \"reg\" property\n"); + of_node_put(ports); + of_node_put(port); + return err; + } + + /* Apply only for rgmii port */ + if (!lan937x_is_rgmii_port(dev, p)) + continue; + + if (of_property_read_u32(port, "rx-internal-delay-ps", &val)) + val = 0; + + err = lan937x_set_rgmii_delay(dev, p, val, false); + if (err) + break; + + if (of_property_read_u32(port, "tx-internal-delay-ps", &val)) + val = 0; + + err = lan937x_set_rgmii_delay(dev, p, val, true); + if (err) + break; + } + + of_node_put(ports); + return err; +} + +static int lan937x_setup(struct dsa_switch *ds) +{ + struct ksz_device *dev = ds->priv; + u32 data32; + u8 data8; + int ret; + + ret = lan937x_reset_switch(dev); + if (ret < 0) + return ret; + + ret = ksz_read8(dev, REG_SW_LUE_CTRL_1, &data8); + if (ret < 0) + return ret; + + /* Enable Auto Aging */ + ret = ksz_write8(dev, REG_SW_LUE_CTRL_1, data8 | SW_LINK_AUTO_AGING); + if (ret < 0) + return ret; + + /* disable interrupts */ + ret = ksz_write32(dev, REG_SW_INT_MASK__4, SWITCH_INT_MASK); + if (ret < 0) + return ret; + + ret = ksz_write32(dev, REG_SW_PORT_INT_MASK__4, 0xFF); + if (ret < 0) + return ret; + + /* Read interrupt status register */ + ret = ksz_read32(dev, REG_SW_PORT_INT_STATUS__4, &data32); + if (ret < 0) + return ret; + + /* Apply rgmii internal delay for the mac based on device tree */ + ret = lan937x_parse_dt_rgmii_delay(dev); + if (ret < 0) + return ret; + + /* The VLAN aware is a global setting. Mixed vlan + * filterings are not supported. + */ + ds->vlan_filtering_is_global = true; + + /* Configure cpu port */ + lan937x_config_cpu_port(ds); + + /* Enable aggressive back off for half duplex & UNH mode */ + lan937x_cfg(dev, REG_SW_MAC_CTRL_0, + (SW_PAUSE_UNH_MODE | SW_NEW_BACKOFF | SW_AGGR_BACKOFF), + true); + + /* If NO_EXC_COLLISION_DROP bit is set, the switch will not drop + * packets when 16 or more collisions occur + */ + lan937x_cfg(dev, REG_SW_MAC_CTRL_1, NO_EXC_COLLISION_DROP, true); + + /* Enable reserved multicast table */ + lan937x_cfg(dev, REG_SW_LUE_CTRL_0, SW_RESV_MCAST_ENABLE, true); + + /* enable global MIB counter freeze function */ + lan937x_cfg(dev, REG_SW_MAC_CTRL_6, SW_MIB_COUNTER_FREEZE, true); + + /* disable CLK125 & CLK25, 1: disable, 0: enable */ + lan937x_cfg(dev, REG_SW_GLOBAL_OUTPUT_CTRL__1, + (SW_CLK125_ENB | SW_CLK25_ENB), true); + + /* start switch */ + lan937x_cfg(dev, REG_SW_OPERATION, SW_START, true); + + return 0; +} + +const struct dsa_switch_ops lan937x_switch_ops = { + .get_tag_protocol = lan937x_get_tag_protocol, + .setup = lan937x_setup, + .port_enable = ksz_enable_port, + .port_bridge_join = ksz_port_bridge_join, + .port_bridge_leave = ksz_port_bridge_leave, + .port_stp_state_set = lan937x_port_stp_state_set, +}; + +int lan937x_switch_register(struct ksz_device *dev) +{ + return ksz_switch_register(dev, &lan937x_dev_ops); +} +EXPORT_SYMBOL(lan937x_switch_register); + +MODULE_AUTHOR("Prasanna Vengateshan Varadharajan <Prasanna.Vengateshan@xxxxxxxxxxxxx>"); +MODULE_DESCRIPTION("Microchip LAN937x Series Switch DSA Driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/net/dsa/microchip/lan937x_reg.h b/drivers/net/dsa/microchip/lan937x_reg.h new file mode 100644 index 000000000000..d0de595f6c4e --- /dev/null +++ b/drivers/net/dsa/microchip/lan937x_reg.h @@ -0,0 +1,688 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* Microchip LAN937X switch register definitions + * Copyright (C) 2019-2021 Microchip Technology Inc. + */ +#ifndef __LAN937X_REG_H +#define __LAN937X_REG_H + +/* 0 - Operation */ +#define REG_CHIP_ID0__1 0x0000 +#define REG_CHIP_ID1__1 0x0001 +#define REG_CHIP_ID2__1 0x0002 + +#define CHIP_ID_74 0x74 +#define CHIP_ID_73 0x73 +#define CHIP_ID_72 0x72 +#define CHIP_ID_71 0x71 +#define CHIP_ID_70 0x70 + +#define REG_CHIP_ID3__1 0x0003 + +#define REG_GLOBAL_CTRL_0 0x0007 + +#define SW_PHY_REG_BLOCK BIT(7) +#define SW_FAST_MODE BIT(3) +#define SW_FAST_MODE_OVERRIDE BIT(2) + +#define REG_GLOBAL_OPTIONS 0x000F + +#define REG_SW_INT_STATUS__4 0x0010 +#define REG_SW_INT_MASK__4 0x0014 + +#define LUE_INT BIT(31) +#define TRIG_TS_INT BIT(30) +#define APB_TIMEOUT_INT BIT(29) +#define OVER_TEMP_INT BIT(28) +#define HSR_INT BIT(27) +#define PIO_INT BIT(26) +#define POR_READY_INT BIT(25) + +#define SWITCH_INT_MASK \ + (LUE_INT | TRIG_TS_INT | APB_TIMEOUT_INT | OVER_TEMP_INT | HSR_INT | \ + PIO_INT | POR_READY_INT) + +#define REG_SW_PORT_INT_STATUS__4 0x0018 +#define REG_SW_PORT_INT_MASK__4 0x001C + +/* 1 - Global */ +#define REG_SW_GLOBAL_SERIAL_CTRL_0 0x0100 + +#define SW_LITTLE_ENDIAN BIT(4) +#define SPI_AUTO_EDGE_DETECTION BIT(1) +#define SPI_CLOCK_OUT_RISING_EDGE BIT(0) + +#define REG_SW_GLOBAL_OUTPUT_CTRL__1 0x0103 +#define SW_CLK125_ENB BIT(1) +#define SW_CLK25_ENB BIT(0) + +/* 2 - PHY */ +#define REG_SW_POWER_MANAGEMENT_CTRL 0x0201 + +/* 3 - Operation Control */ +#define REG_SW_OPERATION 0x0300 + +#define SW_DOUBLE_TAG BIT(7) +#define SW_OVER_TEMP_ENABLE BIT(2) +#define SW_RESET BIT(1) +#define SW_START BIT(0) + +#define REG_SW_LUE_CTRL_0 0x0310 +#define SW_VLAN_ENABLE BIT(7) +#define SW_DROP_INVALID_VID BIT(6) +#define SW_AGE_CNT_M 0x7 +#define SW_AGE_CNT_S 3 +#define SW_RESV_MCAST_ENABLE BIT(2) + +#define REG_SW_LUE_CTRL_1 0x0311 + +#define UNICAST_LEARN_DISABLE BIT(7) +#define SW_FLUSH_STP_TABLE BIT(5) +#define SW_FLUSH_MSTP_TABLE BIT(4) +#define SW_SRC_ADDR_FILTER BIT(3) +#define SW_AGING_ENABLE BIT(2) +#define SW_FAST_AGING BIT(1) +#define SW_LINK_AUTO_AGING BIT(0) + +#define REG_SW_LUE_CTRL_2 0x0312 + +#define SW_MID_RANGE_AGE BIT(7) +#define SW_LINK_DOWN_FLUSH BIT(6) +#define SW_EGRESS_VLAN_FILTER_DYN BIT(5) +#define SW_EGRESS_VLAN_FILTER_STA BIT(4) +#define SW_FLUSH_OPTION_M 0x3 +#define SW_FLUSH_OPTION_S 2 +#define SW_FLUSH_OPTION_DYN_MAC 1 +#define SW_FLUSH_OPTION_STA_MAC 2 +#define SW_FLUSH_OPTION_BOTH 3 + +#define REG_SW_LUE_CTRL_3 0x0313 +#define REG_SW_AGE_PERIOD__1 0x0313 + +#define REG_SW_LUE_INT_STATUS__1 0x0314 +#define REG_SW_LUE_INT_MASK__1 0x0315 + +#define LEARN_FAIL_INT BIT(2) +#define WRITE_FAIL_INT BIT(0) + +#define LUE_INT_MASK (LEARN_FAIL_INT | WRITE_FAIL_INT) + +#define REG_SW_LUE_INDEX_0__2 0x0316 + +#define ENTRY_INDEX_M 0x0FFF + +#define REG_SW_LUE_INDEX_1__2 0x0318 + +#define FAIL_INDEX_M 0x03FF + +#define REG_SW_LUE_INDEX_2__2 0x031A + +#define REG_SW_STATIC_AVAIL_ENTRY__4 0x031C + +#define SW_INGRESS_FILTERING_NO_LEARN BIT(15) +#define SW_STATIC_AVAIL_CNT 0x1FF + +#define REG_SW_AGE_PERIOD__2 0x0320 +#define SW_AGE_PERIOD_M 0xFFF + +#define REG_SW_LUE_UNK_UCAST_CTRL__2 0x0322 +#define REG_SW_LUE_UNK_CTRL_0__4 0x0322 + +#define SW_UNK_UCAST_ENABLE BIT(15) +#define SW_UNK_PORTS_M 0xFF + +#define REG_SW_LUE_UNK_MCAST_CTRL__2 0x0324 +#define SW_UNK_MCAST_ENABLE BIT(15) + +#define REG_SW_LUE_UNK_VID_CTRL__2 0x0326 +#define SW_UNK_VID_ENABLE BIT(15) + +#define SW_VLAN_FLUSH_PORTS_M 0xFF + +#define REG_SW_STATIC_ENTRY_LIMIT__4 0x032C + +#define REG_SW_MAC_CTRL_0 0x0330 +#define SW_NEW_BACKOFF BIT(7) +#define SW_PAUSE_UNH_MODE BIT(1) +#define SW_AGGR_BACKOFF BIT(0) + +#define REG_SW_MAC_CTRL_1 0x0331 +#define SW_SHORT_IFG BIT(7) +#define MULTICAST_STORM_DISABLE BIT(6) +#define SW_BACK_PRESSURE BIT(5) +#define FAIR_FLOW_CTRL BIT(4) +#define NO_EXC_COLLISION_DROP BIT(3) +#define SW_LEGAL_PACKET_DISABLE BIT(1) +#define SW_PASS_SHORT_FRAME BIT(0) + +#define REG_SW_MAC_CTRL_2 0x0332 +#define SW_REPLACE_VID BIT(3) +#define BROADCAST_STORM_RATE_HI 0x07 + +#define REG_SW_MAC_CTRL_3 0x0333 +#define BROADCAST_STORM_RATE_LO 0xFF +#define BR_STORM_RATE 0x07FF + +#define REG_SW_MAC_CTRL_4 0x0334 +#define SW_PASS_PAUSE BIT(3) + +#define REG_SW_MAC_CTRL_5 0x0335 +#define SW_OUT_RATE_LIMIT_QUEUE_BASED BIT(3) + +#define REG_SW_MAC_CTRL_6 0x0336 +#define SW_MIB_COUNTER_FLUSH BIT(7) +#define SW_MIB_COUNTER_FREEZE BIT(6) + +#define REG_SW_MRI_CTRL_0 0x0370 +#define SW_IGMP_SNOOP BIT(6) +#define SW_IPV6_MLD_OPTION BIT(3) +#define SW_IPV6_MLD_SNOOP BIT(2) +#define SW_MIRROR_RX_TX BIT(0) + +#define REG_SW_MRI_CTRL_1__4 0x0374 +#define REG_SW_MRI_CTRL_2__4 0x0378 +#define REG_SW_CLASS_D_IP_CTRL__4 0x0374 + +#define SW_CLASS_D_IP_ENABLE BIT(31) + +#define REG_SW_MRI_CTRL_8 0x0378 +#define SW_RED_COLOR_S 4 +#define SW_YELLOW_COLOR_S 2 +#define SW_GREEN_COLOR_S 0 +#define SW_COLOR_M 0x3 + +#define REG_PTP_EVENT_PRIO_CTRL 0x037C +#define REG_PTP_GENERAL_PRIO_CTRL 0x037D +#define PTP_PRIO_ENABLE BIT(7) + +#define REG_SW_QM_CTRL__4 0x0390 +#define PRIO_SCHEME_SELECT_M KS_PRIO_M +#define PRIO_SCHEME_SELECT_S 6 +#define PRIO_MAP_3_HI 0 +#define PRIO_MAP_2_HI 2 +#define PRIO_MAP_0_LO 3 +#define UNICAST_VLAN_BOUNDARY BIT(1) + +#define REG_SW_EEE_QM_CTRL__2 0x03C0 +#define REG_SW_EEE_TXQ_WAIT_TIME__2 0x03C2 + +/* 4 - */ +#define REG_SW_VLAN_ENTRY__4 0x0400 +#define VLAN_VALID BIT(31) +#define VLAN_FORWARD_OPTION BIT(27) +#define VLAN_PRIO_M KS_PRIO_M +#define VLAN_PRIO_S 24 +#define VLAN_MSTP_M 0x7 +#define VLAN_MSTP_S 12 +#define VLAN_FID_M 0x7F + +#define REG_SW_VLAN_ENTRY_UNTAG__4 0x0404 +#define REG_SW_VLAN_ENTRY_PORTS__4 0x0408 +#define REG_SW_VLAN_ENTRY_INDEX__2 0x040C + +#define VLAN_INDEX_M 0x0FFF + +#define REG_SW_VLAN_CTRL 0x040E +#define VLAN_START BIT(7) +#define VLAN_ACTION 0x3 +#define VLAN_WRITE 1 +#define VLAN_READ 2 +#define VLAN_CLEAR 3 + +#define REG_SW_ALU_INDEX_0 0x0410 +#define ALU_FID_INDEX_S 16 +#define ALU_FID_SIZE 127 +#define ALU_MAC_ADDR_HI 0xFFFF + +#define REG_SW_ALU_INDEX_1 0x0414 +#define ALU_DIRECT_INDEX_M (BIT(12) - 1) + +#define REG_SW_ALU_CTRL__4 0x0418 +#define REG_SW_ALU_CTRL(num) (REG_SW_ALU_CTRL__4 + ((num) * 4)) + +#define ALU_STA_DYN_CNT 2 +#define ALU_VALID_CNT_M (BIT(14) - 1) +#define ALU_VALID_CNT_S 16 +#define ALU_START BIT(7) +#define ALU_VALID BIT(6) +#define ALU_VALID_OR_STOP BIT(5) +#define ALU_DIRECT BIT(2) +#define ALU_ACTION 0x3 +#define ALU_WRITE 1 +#define ALU_READ 2 +#define ALU_SEARCH 3 + +#define REG_SW_ALU_STAT_CTRL__4 0x041C +#define ALU_STAT_VALID_CNT_M (BIT(9) - 1) +#define ALU_STAT_VALID_CNT_S 20 +#define ALU_STAT_INDEX_M (BIT(8) - 1) +#define ALU_STAT_INDEX_S 8 +#define ALU_RESV_MCAST_INDEX_M (BIT(6) - 1) +#define ALU_STAT_START BIT(7) +#define ALU_STAT_VALID BIT(6) +#define ALU_STAT_VALID_OR_STOP BIT(5) +#define ALU_STAT_USE_FID BIT(4) +#define ALU_STAT_DIRECT BIT(3) +#define ALU_RESV_MCAST_ADDR BIT(2) +#define ALU_STAT_ACTION 0x3 +#define ALU_STAT_WRITE 1 +#define ALU_STAT_READ 2 +#define ALU_STAT_SEARCH 3 + +#define REG_SW_ALU_VAL_A 0x0420 +#define ALU_V_STATIC_VALID BIT(31) +#define ALU_V_SRC_FILTER BIT(30) +#define ALU_V_DST_FILTER BIT(29) +#define ALU_V_PRIO_AGE_CNT_M (BIT(3) - 1) +#define ALU_V_PRIO_AGE_CNT_S 26 +#define ALU_V_MSTP_M 0x7 + +#define REG_SW_ALU_VAL_B 0x0424 +#define ALU_V_OVERRIDE BIT(31) +#define ALU_V_USE_FID BIT(30) +#define ALU_V_PORT_MAP 0xFF + +#define REG_SW_ALU_VAL_C 0x0428 +#define ALU_V_FID_M (BIT(16) - 1) +#define ALU_V_FID_S 16 +#define ALU_V_MAC_ADDR_HI 0xFFFF + +#define REG_SW_ALU_VAL_D 0x042C + +#define PORT_CTRL_ADDR(port, addr) ((addr) | (((port) + 1) << 12)) + +#define REG_GLOBAL_RR_INDEX__1 0x0600 + +/* VPHY */ +#define REG_VPHY_CTRL__2 0x0700 +#define REG_VPHY_STAT__2 0x0704 +#define REG_VPHY_ID_HI__2 0x0708 +#define REG_VPHY_ID_LO__2 0x070C +#define REG_VPHY_AUTO_NEG__2 0x0710 +#define REG_VPHY_REMOTE_CAP__2 0x0714 + +#define REG_VPHY_EXPANSION__2 0x0718 + +#define REG_VPHY_M_CTRL__2 0x0724 +#define REG_VPHY_M_STAT__2 0x0728 + +#define REG_VPHY_EXT_STAT__2 0x073C +#define VPHY_EXT_1000_X_FULL BIT(15) +#define VPHY_EXT_1000_X_HALF BIT(14) +#define VPHY_EXT_1000_T_FULL BIT(13) +#define VPHY_EXT_1000_T_HALF BIT(12) + +#define REG_VPHY_DEVAD_0__2 0x0740 +#define REG_VPHY_DEVAD_1__2 0x0744 +#define REG_VPHY_DEVAD_2__2 0x0748 +#define REG_VPHY_DEVAD_3__2 0x074C + +#define VPHY_DEVAD_UPDATE BIT(7) +#define VPHY_DEVAD_M 0x1F +#define VPHY_DEVAD_S 8 + +#define REG_VPHY_SMI_ADDR__2 0x0750 +#define REG_VPHY_SMI_DATA_LO__2 0x0754 +#define REG_VPHY_SMI_DATA_HI__2 0x0758 + +#define REG_VPHY_IND_ADDR__2 0x075C +#define REG_VPHY_IND_DATA__2 0x0760 +#define REG_VPHY_IND_CTRL__2 0x0768 + +#define VPHY_IND_WRITE BIT(1) +#define VPHY_IND_BUSY BIT(0) + +#define REG_VPHY_SPECIAL_CTRL__2 0x077C +#define VPHY_SMI_INDIRECT_ENABLE BIT(15) +#define VPHY_SW_LOOPBACK BIT(14) +#define VPHY_MDIO_INTERNAL_ENABLE BIT(13) +#define VPHY_SPI_INDIRECT_ENABLE BIT(12) +#define VPHY_PORT_MODE_M 0x3 +#define VPHY_PORT_MODE_S 8 +#define VPHY_MODE_RGMII 0 +#define VPHY_MODE_MII_PHY 1 +#define VPHY_MODE_SGMII 2 +#define VPHY_MODE_RMII_PHY 3 +#define VPHY_SW_COLLISION_TEST BIT(7) +#define VPHY_SPEED_DUPLEX_STAT_M 0x7 +#define VPHY_SPEED_DUPLEX_STAT_S 2 +#define VPHY_SPEED_1000 BIT(4) +#define VPHY_SPEED_100 BIT(3) +#define VPHY_FULL_DUPLEX BIT(2) + +/* 0 - Operation */ +#define REG_PORT_DEFAULT_VID 0x0000 + +#define REG_PORT_CUSTOM_VID 0x0002 +#define REG_PORT_PME_STATUS 0x0013 + +#define REG_PORT_PME_CTRL 0x0017 +#define PME_WOL_MAGICPKT BIT(2) +#define PME_WOL_LINKUP BIT(1) +#define PME_WOL_ENERGY BIT(0) + +#define REG_PORT_INT_STATUS 0x001B +#define REG_PORT_INT_MASK 0x001F + +#define PORT_TAS_INT BIT(5) +#define PORT_SGMII_INT BIT(3) +#define PORT_PTP_INT BIT(2) +#define PORT_PHY_INT BIT(1) +#define PORT_ACL_INT BIT(0) + +#define PORT_INT_MASK \ + ( \ + PORT_TAS_INT | \ + PORT_SGMII_INT | PORT_PTP_INT | PORT_PHY_INT | PORT_ACL_INT) + +#define REG_PORT_CTRL_0 0x0020 + +#define PORT_MAC_LOOPBACK BIT(7) +#define PORT_MAC_REMOTE_LOOPBACK BIT(6) +#define PORT_K2L_INSERT_ENABLE BIT(5) +#define PORT_K2L_DEBUG_ENABLE BIT(4) +#define PORT_TAIL_TAG_ENABLE BIT(2) +#define PORT_QUEUE_SPLIT_ENABLE 0x3 + +#define REG_PORT_CTRL_1 0x0021 +#define PORT_SRP_ENABLE 0x3 + +#define REG_PORT_STATUS_0 0x0030 +#define PORT_INTF_SPEED_M 0x3 +#define PORT_INTF_SPEED_S 3 +#define PORT_INTF_FULL_DUPLEX BIT(2) + +#define REG_PORT_STATUS_1 0x0034 + +/* 1 - PHY */ +#define REG_VPHY_SMI_ADDR 0x14 +#define REG_VPHY_SMI_DATA_LO 0x15 +#define REG_VPHY_SMI_DATA_HI 0x16 + +#define REG_VPHY_SPECIAL_CTRL_STAT 0x1F + +#define REG_PORT_T1_PHY_CTRL_BASE 0x0100 +#define REG_PORT_TX_PHY_CTRL_BASE 0x0280 +#define REG_TX_PHY_CTRL_BASE 0x0980 + +#define REG_PORT_PHY_1000_CTRL 0x0112 +#define PORT_AUTO_NEG_MANUAL BIT(12) +#define PORT_AUTO_NEG_M BIT(11) +#define PORT_AUTO_NEG_M_PREFERRED BIT(10) +#define PORT_AUTO_NEG_1000BT_FD BIT(9) +#define PORT_AUTO_NEG_1000BT BIT(8) + +#define REG_PORT_PHY_1000_STATUS 0x0114 + +#define REG_PORT_PHY_RXER_COUNTER 0x012A +#define REG_PORT_PHY_INT_ENABLE 0x0136 +#define REG_PORT_PHY_INT_STATUS 0x0137 + +/* Same as PORT_PHY_LOOPBACK */ +#define PORT_PHY_PCS_LOOPBACK BIT(0) + +#define REG_PORT_PHY_DIGITAL_DEBUG_2 0x013A + +#define REG_PORT_PHY_DIGITAL_DEBUG_3 0x013C +#define PORT_100BT_FIXED_LATENCY BIT(15) + +#define REG_PORT_PHY_PHY_CTRL 0x013E +#define PORT_INT_PIN_HIGH BIT(14) +#define PORT_ENABLE_JABBER BIT(9) +#define PORT_STAT_SPEED_1000MBIT BIT(6) +#define PORT_STAT_SPEED_100MBIT BIT(5) +#define PORT_STAT_SPEED_10MBIT BIT(4) +#define PORT_STAT_FULL_DUPLEX BIT(3) + +/* Same as PORT_PHY_STAT_M */ +#define PORT_STAT_M BIT(2) +#define PORT_RESET BIT(1) +#define PORT_LINK_STATUS_FAIL BIT(0) + +/* 3 - xMII */ +#define REG_PORT_XMII_CTRL_0 0x0300 +#define PORT_SGMII_SEL BIT(7) +#define PORT_MII_FULL_DUPLEX BIT(6) +#define PORT_MII_TX_FLOW_CTRL BIT(5) +#define PORT_MII_100MBIT BIT(4) +#define PORT_MII_RX_FLOW_CTRL BIT(3) +#define PORT_GRXC_ENABLE BIT(0) + +#define REG_PORT_XMII_CTRL_1 0x0301 +#define PORT_MII_NOT_1GBIT BIT(6) +#define PORT_MII_SEL_EDGE BIT(5) +#define PORT_RGMII_ID_IG_ENABLE BIT(4) +#define PORT_RGMII_ID_EG_ENABLE BIT(3) +#define PORT_MII_MAC_MODE BIT(2) +#define PORT_MII_SEL_M 0x3 +#define PORT_RGMII_SEL 0x0 +#define PORT_RMII_SEL 0x1 +#define PORT_MII_SEL 0x2 + +#define REG_PORT_XMII_CTRL_2 0x0302 +#define PORT_RGMII_RX_STS_ENABLE BIT(0) + +#define REG_PORT_XMII_CTRL_3 0x0303 +#define PORT_DUPLEX_STATUS_FULL BIT(3) + +#define REG_PORT_XMII_CTRL_4 0x0304 +#define PORT_TX_TUNE_ADJ 0x3F80 + +#define REG_PORT_XMII_CTRL_5 0x0306 +#define PORT_DLL_RESET BIT(15) +#define PORT_RX_TUNE_ADJ 0x3F80 + +#define PORT_TUNE_ADJ 0x3F80 + +/* 4 - MAC */ +#define REG_PORT_MAC_CTRL_0 0x0400 +#define PORT_CHECK_LENGTH BIT(2) +#define PORT_BROADCAST_STORM BIT(1) +#define PORT_JUMBO_PACKET BIT(0) + +#define REG_PORT_MAC_CTRL_1 0x0401 +#define PORT_BACK_PRESSURE BIT(3) +#define PORT_PASS_ALL BIT(0) + +#define REG_PORT_MAC_CTRL_2 0x0402 +#define PORT_100BT_EEE_DISABLE BIT(7) +#define PORT_1000BT_EEE_DISABLE BIT(6) + +#define REG_PORT_MAC_IN_RATE_LIMIT 0x0403 + +#define REG_PORT_MTU__2 0x0404 +#define PORT_RATE_LIMIT_M (BIT(7) - 1) + +/* 5 - MIB Counters */ +#define REG_PORT_MIB_CTRL_STAT 0x0500 +#define MIB_COUNTER_OVERFLOW BIT(31) +#define MIB_COUNTER_VALID BIT(30) +#define MIB_COUNTER_READ BIT(25) +#define MIB_COUNTER_FLUSH_FREEZE BIT(24) +#define MIB_COUNTER_INDEX_M (BIT(8) - 1) +#define MIB_COUNTER_INDEX_S 16 +#define MIB_COUNTER_DATA_HI_M 0xF + +#define REG_PORT_MIB_DATA 0x0504 + +/* 8 - Classification and Policing */ +#define REG_PORT_MRI_MIRROR_CTRL 0x0800 +#define PORT_MIRROR_RX BIT(6) +#define PORT_MIRROR_TX BIT(5) +#define PORT_MIRROR_SNIFFER BIT(1) + +#define REG_PORT_MRI_PRIO_CTRL 0x0801 +#define PORT_HIGHEST_PRIO BIT(7) +#define PORT_OR_PRIO BIT(6) +#define PORT_MAC_PRIO_ENABLE BIT(4) +#define PORT_VLAN_PRIO_ENABLE BIT(3) +#define PORT_802_1P_PRIO_ENABLE BIT(2) +#define PORT_DIFFSERV_PRIO_ENABLE BIT(1) +#define PORT_ACL_PRIO_ENABLE BIT(0) + +#define REG_PORT_MRI_MAC_CTRL 0x0802 +#define PORT_USER_PRIO_CEILING BIT(7) +#define PORT_DROP_NON_VLAN BIT(4) +#define PORT_DROP_TAG BIT(3) +#define PORT_BASED_PRIO_M KS_PRIO_M +#define PORT_BASED_PRIO_S 0 + +#define REG_PORT_MRI_TC_MAP__4 0x0808 + +/* 9 - Shaping */ +#define REG_PORT_MTI_QUEUE_INDEX__4 0x0900 + +#define REG_PORT_MTI_QUEUE_CTRL_0__4 0x0904 +#define MTI_PVID_REPLACE BIT(0) + +#define REG_PORT_MTI_QUEUE_CTRL_0 0x0914 + +/* A - QM */ +#define REG_PORT_QM_CTRL__4 0x0A00 +#define PORT_QM_DROP_PRIO_M 0x3 + +#define REG_PORT_VLAN_MEMBERSHIP__4 0x0A04 + +#define REG_PORT_QM_QUEUE_INDEX__4 0x0A08 +#define PORT_QM_QUEUE_INDEX_S 24 +#define PORT_QM_BURST_SIZE_S 16 +#define PORT_QM_MIN_RESV_SPACE_M (BIT(11) - 1) + +#define REG_PORT_QM_WATER_MARK__4 0x0A0C +#define PORT_QM_HI_WATER_MARK_S 16 +#define PORT_QM_LO_WATER_MARK_S 0 +#define PORT_QM_WATER_MARK_M (BIT(11) - 1) + +#define REG_PORT_QM_TX_CNT_0__4 0x0A10 +#define PORT_QM_TX_CNT_USED_S 0 +#define PORT_QM_TX_CNT_M (BIT(11) - 1) + +#define REG_PORT_QM_TX_CNT_1__4 0x0A14 +#define PORT_QM_TX_CNT_CALCULATED_S 16 +#define PORT_QM_TX_CNT_AVAIL_S 0 + +/* B - LUE */ +#define REG_PORT_LUE_CTRL 0x0B00 + +#define PORT_VLAN_LOOKUP_VID_0 BIT(7) +#define PORT_INGRESS_FILTER BIT(6) +#define PORT_DISCARD_NON_VID BIT(5) +#define PORT_MAC_BASED_802_1X BIT(4) +#define PORT_SRC_ADDR_FILTER BIT(3) + +#define REG_PORT_LUE_MSTP_INDEX 0x0B01 + +#define REG_PORT_LUE_MSTP_STATE 0x0B04 + +#define PORT_TX_ENABLE BIT(2) +#define PORT_RX_ENABLE BIT(1) +#define PORT_LEARN_DISABLE BIT(0) + +#define REG_PORT_LUE_LEARN_CNT__2 0x0B08 + +#define REG_PORT_LUE_UNK_CTL0 0x0B0E +#define REG_PORT_LUE_UNK_CTL1 0x0B10 +#define REG_PORT_LUE_UNK_VID_CTRL__2 0x0B12 + +#define PORT_UNK_UCAST_MCAST_ENABLE BIT(15) +#define PORT_UCAST_MCAST_MASK 0xFF +#define PORT_UNK_VID_ENABLE BIT(15) + +#define PRIO_QUEUES 8 +#define RX_PRIO_QUEUES 8 +#define KS_PRIO_IN_REG 2 +#define TOTAL_PORT_NUM 8 + +#define LAN937X_COUNTER_NUM 0x20 +#define TOTAL_LAN937X_COUNTER_NUM (LAN937X_COUNTER_NUM + 2 + 2) + +#define SWITCH_COUNTER_NUM LAN937X_COUNTER_NUM + +#define P_BCAST_STORM_CTRL REG_PORT_MAC_CTRL_0 +#define P_PRIO_CTRL REG_PORT_MRI_PRIO_CTRL +#define P_MIRROR_CTRL REG_PORT_MRI_MIRROR_CTRL +#define P_STP_CTRL REG_PORT_LUE_MSTP_STATE +#define P_PHY_CTRL REG_PORT_PHY_CTRL +#define P_NEG_RESTART_CTRL REG_PORT_PHY_CTRL +#define P_LINK_STATUS REG_PORT_PHY_STATUS +#define P_SPEED_STATUS REG_PORT_PHY_PHY_CTRL +#define P_RATE_LIMIT_CTRL REG_PORT_MAC_IN_RATE_LIMIT + +#define S_LINK_AGING_CTRL REG_SW_LUE_CTRL_1 +#define S_MIRROR_CTRL REG_SW_MRI_CTRL_0 +#define S_REPLACE_VID_CTRL REG_SW_MAC_CTRL_2 +#define S_802_1P_PRIO_CTRL REG_SW_MAC_802_1P_MAP_0 +#define S_TOS_PRIO_CTRL REG_SW_MAC_TOS_PRIO_0 +#define S_FLUSH_TABLE_CTRL REG_SW_LUE_CTRL_1 + +#define REG_SWITCH_RESET REG_RESET_CTRL + +#define SW_FLUSH_DYN_MAC_TABLE SW_FLUSH_MSTP_TABLE + +#define MAX_TIMESTAMP_UNIT 2 +#define MAX_TRIG_UNIT 3 +#define MAX_TIMESTAMP_EVENT_UNIT 8 +#define MAX_GPIO 2 +#define MAX_CLOCK 2 + +#define PTP_TRIG_UNIT_M (BIT(MAX_TRIG_UNIT) - 1) +#define PTP_TS_UNIT_M (BIT(MAX_TIMESTAMP_UNIT) - 1) + +#define TAIL_TAG_PTP BIT(7) +#define TAIL_TAG_NEXT_CHIP BIT(6) +#define TAIL_TAG_K2L BIT(5) +#define TAIL_TAG_PTP_1_STEP BIT(4) +#define TAIL_TAG_PTP_P2P BIT(3) +#define TAIL_TAG_RX_PORTS_M 0x7 + +/* 148,800 frames * 67 ms / 100 */ +#define BR_STORM_VALUE 9969 + +#define SW_CHECK_LENGTH BIT(3) + +#define FR_MIN_SIZE 1522 +#define FR_MAX_SIZE 9000 + +#define PORT_JUMBO_EN BIT(0) +#define PORT_FR_CHK_LENGTH BIT(2) +#define PORT_MAX_FR_SIZE 0x404 + +#define FR_SIZE_CPU_PORT 1540 + +#define REG_PORT_CTRL_0 0x0020 +#define PORT_FULL_DUPLEX BIT(6) +#define PORT_TX_FLOW_CTRL BIT(5) +#define PORT_RX_FLOW_CTRL BIT(3) +#define PORT_MAC_SPEED_100 BIT(4) + +#define PORT_QUEUE_SPLIT_ENABLE 0x3 + +/* Get fid from vid, fid 0 is not used if vid is greater than 127 */ +#define LAN937X_GET_FID(vid) (((vid) % ALU_FID_SIZE) + 1) + +/* Driver set switch broadcast storm protection at 10% rate */ +#define BR_STORM_PROT_RATE 10 + +#define MII_BMSR_100BASE_TX_FD BIT(14) + +#define PHY_LINK_UP 1 +#define PHY_LINK_DOWN 0 + +/* The port number as per the datasheet */ +#define RGMII_2_PORT_NUM 5 +#define RGMII_1_PORT_NUM 6 +#define SGMII_PORT_NUM 4 +#define TXPHY_PORT_NUM 4 + +#define GET_CHIP_ID_LSB(chip_id) (((chip_id) >> 8) & 0xff) +#define LAN937X_RGMII_2_PORT (RGMII_2_PORT_NUM - 1) +#define LAN937X_RGMII_1_PORT (RGMII_1_PORT_NUM - 1) +#define LAN937X_SGMII_PORT (SGMII_PORT_NUM - 1) +#define LAN937X_TXPHY_PORT (TXPHY_PORT_NUM - 1) +#define LAN937X_TAG_LEN 2 + +#define RGMII_1_TX_DELAY_2NS 2 +#define RGMII_2_TX_DELAY_2NS 0 +#define RGMII_1_RX_DELAY_2NS 0x1B +#define RGMII_2_RX_DELAY_2NS 0x14 + +#endif -- 2.33.0
