Em Mon, Feb 10, 2020 at 05:17:51PM +0100, Jiri Olsa escreveu:
> On Mon, Feb 10, 2020 at 04:51:08PM +0100, Björn Töpel wrote:
> > On Sat, 8 Feb 2020 at 16:42, Jiri Olsa <jolsa@xxxxxxxxxx> wrote:
> > > this patchset adds trampoline and dispatcher objects
> > > to be visible in /proc/kallsyms. The last patch also
> > > adds sorting for all bpf objects in /proc/kallsyms.
> > Thanks for working on this!
> > I'm probably missing something with my perf setup; I've applied your
> > patches, and everything seem to work fine from an kallsyms
> > perspective:
> > # grep bpf_dispatcher_xdp /proc/kallsyms
> > ...
> > ffffffffc0511000 t bpf_dispatcher_xdp [bpf]
> >
> > However, when I run
> > # perf top
> >
> > I still see the undecorated one:
> > 0.90% [unknown] [k] 0xffffffffc0511037
> >
> > Any ideas?
> yea strange.. it should be picked up from /proc/kallsyms as
> fallback if there's no other source, I'll check on that
> (might be the problem with perf depending on address going
> only higher in /proc/kallsyms, while bpf symbols are at the
> end and start over from the lowest bpf address)
>
> anyway, in perf we enumerate bpf_progs via the perf events
> PERF_BPF_EVENT_PROG_LOAD,PERF_BPF_EVENT_PROG_UNLOAD interface
> together with PERF_RECORD_KSYMBOL_TYPE_BPF events
>
> we might need to add something like:
> PERF_RECORD_KSYMBOL_TYPE_BPF_TRAMPOLINE
> PERF_RECORD_KSYMBOL_TYPE_BPF_DISPATCHER
>
> to notify about the area, I'll check on that
>
> however the /proc/kallsyms fallback should work in any
> case.. thanks for report ;-)
We should by now move kallsyms to be the preferred source of symbols,
not vmlinux, right?
Perhaps what is happening is:
[root@quaco ~]# strace -f -e open,openat -o /tmp/bla perf top
[root@quaco ~]# grep vmlinux /tmp/bla
11013 openat(AT_FDCWD, "vmlinux", O_RDONLY) = -1 ENOENT (No such file or directory)
11013 openat(AT_FDCWD, "/boot/vmlinux", O_RDONLY) = -1 ENOENT (No such file or directory)
11013 openat(AT_FDCWD, "/boot/vmlinux-5.5.0+", O_RDONLY) = -1 ENOENT (No such file or directory)
11013 openat(AT_FDCWD, "/usr/lib/debug/boot/vmlinux-5.5.0+", O_RDONLY) = -1 ENOENT (No such file or directory)
11013 openat(AT_FDCWD, "/lib/modules/5.5.0+/build/vmlinux", O_RDONLY) = 152
[root@quaco ~]#
I.e. it is using vmlinux for resolving symbols and he should try with:
[root@quaco ~]# strace -f -e open,openat -o /tmp/bla perf top --ignore-vmlinux
[root@quaco ~]# perf top -h vmlinux
Usage: perf top [<options>]
-k, --vmlinux <file> vmlinux pathname
--ignore-vmlinux don't load vmlinux even if found
[root@quaco ~]# grep vmlinux /tmp/bla
[root@quaco ~]#
Historically vmlinux was preferred because it contains function sizes,
but with all these out of the blue symbols, we need to prefer starting
with /proc/kallsyms and, as we do now, continue getting updates via
PERF_RECORD_KSYMBOL.
Humm, but then trampolines don't generate that, right? Or does it? If it
doesn't, then we will know about just the trampolines in place when the
record/top session starts, reparsing /proc/kallsyms periodically seems
excessive?
- Arnaldo
