Re: i2c ERROR H3ULCB #renesas

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Francesco,

Are you sure that these messages where not here before ?

Did they appeared after a precise event (update, reboot, crash, any issue) ?

Are you sure that your H3ULCB is well connected to your Kingfisher (maybe you can try to unplug and plug it again) ?

Are you seeing any problem when using the HDMI port that you weren't before ? (CN49)

Maybe it's just a trivial message that is here for a while but I'm trying to be sure of that !

Thanks for your answers !

Regards, Aymeric Aillet

On 22/12/2021 16:21, Francesco ARGENTIERI (KINETON) wrote:

Hi Ronan,

Thank you for your reply. Please call me Francesco.

To answer your question:

[    0.000158] NOTICE:  BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.21
[    0.005720] NOTICE:  BL2: PRR is R-Car H3 Ver.3.0
[    0.010384] NOTICE:  BL2: Board is Starter Kit Rev.---
[    0.015504] NOTICE:  BL2: Boot device is HyperFlash(80MHz)
[    0.020930] NOTICE:  BL2: LCM state is CM
[    0.024970] NOTICE:  BL2: AVS setting succeeded. DVFS_SetVID=0x53
[    0.030945] NOTICE:  BL2: CH0: 0x400000000 - 0x480000000, 2 GiB
[    0.036807] NOTICE:  BL2: CH1: 0x500000000 - 0x580000000, 2 GiB
[    0.042682] NOTICE:  BL2: CH2: 0x600000000 - 0x680000000, 2 GiB
[    0.048557] NOTICE:  BL2: CH3: 0x700000000 - 0x780000000, 2 GiB
[    0.054446] NOTICE:  BL2: DDR3200(rev.0.33)NOTICE:  [COLD_BOOT]NOTICE:  ..0
[    0.100068] NOTICE:  BL2: DRAM Split is 4ch(DDR f)
[    0.104556] NOTICE:  BL2: QoS is default setting(rev.0.07)
[    0.109999] NOTICE:  BL2: DRAM refresh interval 1.95 usec
[    0.115417] NOTICE:  BL2: Lossy Decomp areas
[    0.119590] NOTICE:       Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
[    0.126674] NOTICE:       Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
[    0.133587] NOTICE:       Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
[    0.140501] NOTICE:  BL2: v1.4(release):15dba6b
[    0.144991] NOTICE:  BL2: Built : 05:32:00, Sep  3 2018
[    0.150179] NOTICE:  BL2: Normal boot
[    0.153825] NOTICE:  BL2: dst=0xe6323d00 src="" len=512(0x200)
[    0.160207] NOTICE:  BL2: dst=0x43f00000 src="" len=6144(0x1800)
[    0.166827] NOTICE:  BL2: dst=0x44000000 src="" len=65536(0x10000)
[    0.174058] NOTICE:  BL2: dst=0x44100000 src="" len=1048576(0x100000)
[    0.188881] NOTICE:  BL2: dst=0x50000000 src="" len=1048576(0x100000)


U-Boot 2015.04 (Sep 03 2018 - 14:33:48)

CPU: Renesas Electronics R8A7795 rev 3.0
Board: H3ULCB
I2C:   ready
DRAM:  7.9 GiB
Bank #0: 0x048000000 - 0x0bfffffff, 1.9 GiB
Bank #1: 0x500000000 - 0x57fffffff, 2 GiB
Bank #2: 0x600000000 - 0x67fffffff, 2 GiB
Bank #3: 0x700000000 - 0x77fffffff, 2 GiB

MMC:   sh-sdhi: 0, sh-sdhi: 1
In:    serial
Out:   serial
Err:   serial
Net:   ravb

I have attached a photo of Kingfisher model.

Best Regard, Francesco

-- 
Regards,
Aymeric Aillet - Embedded system engineer - IoT.bzh
aymeric.aillet@xxxxxxx - www.iot.bzh
_._,_._,_

Links:

You receive all messages sent to this group.

View/Reply Online (#9599) | Reply To Group | Reply To Sender | Mute This Topic | New Topic
Mute #renesas
Your Subscription | Contact Group Owner | Unsubscribe [list-automotive-discussions82@xxxxxxxxxxx]

_._,_._,_

[Index of Archives]     [LARTC]     [Bugtraq]     [Yosemite Forum]     [Photo]

  Powered by Linux