Hello again, I tried once more to install FC3. Here is what I get with dmesg command: I noticed some logs from dmesg are interesting. Kernel disables ata1 port with abnormal status 0x7F. What does this mean? ata: 0x1f0 IDE port busy PCI: Setting latency timer of device 0000:00:1f.2 to 64 ata1: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xE908 irq 15 ATA: abnormal status 0x7F on port 0x177 ata1: disabling port I also tried to load dmread module with command "insmod dmraid". Is that true to load driver with insmod, or is there any driver called "dmraid" or something else (like dm_raid - in fact I tried insmod dm_raid but again I get nothing). I cannot find any documentation about that. Here is the output of dmesg command: ======================================================================== = 8 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected USB Universal Host Controller Interface driver v2.2 ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 3 (level, low) -> IRQ 3 uhci_hcd 0000:00:1d.0: UHCI Host Controller PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: irq 3, io base 0000e000 uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 11 (level, low) -> IRQ 11 uhci_hcd 0000:00:1d.1: UHCI Host Controller PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: irq 11, io base 0000e100 uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 5 (level, low) -> IRQ 5 uhci_hcd 0000:00:1d.2: UHCI Host Controller PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: irq 5, io base 0000e200 uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:1d.3[D] -> GSI 10 (level, low) -> IRQ 10 uhci_hcd 0000:00:1d.3: UHCI Host Controller PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: irq 10, io base 0000e300 uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usb 1-1: new high speed USB device using address 2 usb 4-1: new full speed USB device using address 2 Initializing USB Mass Storage driver... scsi0 : SCSI emulation for USB Mass Storage devices Vendor: USB2.0 Model: CF CardReader Rev: Type: Direct-Access ANSI SCSI revision: 02 Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0 USB Mass Storage device found at 2 scsi1 : SCSI emulation for USB Mass Storage devices Vendor: hp Model: Drive Key Rev: 3.04 Type: Direct-Access ANSI SCSI revision: 02 SCSI device sdb: 127840 512-byte hdwr sectors (65 MB) sdb: Write Protect is off sdb: Mode Sense: 45 00 00 08 sdb: assuming drive cache: write through sdb: sdb1 Attached scsi removable disk sdb at scsi1, channel 0, id 0, lun 0 USB Mass Storage device found at 2 usbcore: registered new driver usb-storage USB Mass Storage support registered. ohci1394: $Rev: 1223 $ Ben Collins <bcollins@xxxxxxxxxx> ACPI: PCI interrupt 0000:02:0a.0[A] -> GSI 5 (level, low) -> IRQ 5 ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[5] MMIO=[d0100000-d01007ff] Max Packet=[2048] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00301bb60000a604] usbcore: deregistering driver usb-storage tg3.c:v3.10 (September 14, 2004) ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:01:00.0 to 64 divert: allocating divert_blk for eth0 eth0: Tigon3 [partno(BCM95751) rev 4001 PHY(5750)] (PCIX:100MHz:32-bit) 10/100/1000BaseT Ethernet 00:30:1b:b6:a5:a0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1] libata version 1.02 loaded. ata_piix version 1.02 ACPI: PCI interrupt 0000:00:1f.2[B] -> GSI 11 (level, low) -> IRQ 11 ata: 0x1f0 IDE port busy PCI: Setting latency timer of device 0000:00:1f.2 to 64 ata1: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xE908 irq 15 ATA: abnormal status 0x7F on port 0x177 ata1: disabling port scsi2 : ata_piix Initializing USB Mass Storage driver... scsi3 : SCSI emulation for USB Mass Storage devices usb 1-1: reset high speed USB device using address 2 Vendor: USB2.0 Model: CF CardReader Rev: Type: Direct-Access ANSI SCSI revision: 02 Attached scsi removable disk sda at scsi3, channel 0, id 0, lun 0 USB Mass Storage device found at 2 scsi4 : SCSI emulation for USB Mass Storage devices usb 4-1: reset full speed USB device using address 2 Vendor: hp Model: Drive Key Rev: 3.04 Type: Direct-Access ANSI SCSI revision: 02 SCSI device sdb: 127840 512-byte hdwr sectors (65 MB) sdb: Write Protect is off sdb: Mode Sense: 45 00 00 08 sdb: assuming drive cache: write through sdb: sdb1 Attached scsi removable disk sdb at scsi4, channel 0, id 0, lun 0 USB Mass Storage device found at 2 usbcore: registered new driver usb-storage USB Mass Storage support registered. ISO 9660 Extensions: Microsoft Joliet Level 3 Unable to load NLS charset utf8 Unable to load NLS charset utf8 ISO 9660 Extensions: RRIP_1991A Unable to identify CD-ROM format. VFS: Can't find ext2 filesystem on dev loop0. security: 3 users, 4 roles, 280 types, 16 bools security: 53 classes, 5494 rules SELinux: Completing initialization. SELinux: Setting up existing superblocks. SELinux: initialized (dev loop0, type cramfs), uses genfs_contexts SELinux: initialized (dev hda, type iso9660), uses genfs_contexts SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts SELinux: initialized (dev usbdevfs, type usbdevfs), uses genfs_contexts SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts SELinux: initialized (dev ram0, type ext2), uses xattr inode_doinit_with_dentry: no dentry for dev=ram0 ino=126 SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts SELinux: initialized (dev mqueue, type mqueue), not configured for labeling SELinux: initialized (dev hugetlbfs, type hugetlbfs), not configured for labeling SELinux: initialized (dev devpts, type devpts), uses transition SIDs SELinux: initialized (dev eventpollfs, type eventpollfs), uses genfs_contexts SELinux: initialized (dev pipefs, type pipefs), uses task SIDs SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts SELinux: initialized (dev sockfs, type sockfs), uses task SIDs SELinux: initialized (dev proc, type proc), uses genfs_contexts SELinux: initialized (dev bdev, type bdev), uses genfs_contexts SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 raid5: automatically using best checksumming function: pIII_sse pIII_sse : 4368.000 MB/sec raid5: using function: pIII_sse (4368.000 MB/sec) md: raid5 personality registered as nr 4 raid6: int32x1 726 MB/s raid6: int32x2 742 MB/s raid6: int32x4 582 MB/s raid6: int32x8 609 MB/s raid6: mmxx1 1703 MB/s raid6: mmxx2 1714 MB/s raid6: sse1x1 839 MB/s raid6: sse1x2 1121 MB/s raid6: sse2x1 1949 MB/s raid6: sse2x2 1855 MB/s raid6: using algorithm sse2x1 (1949 MB/s) md: raid6 personality registered as nr 8 SGI XFS with ACLs, security attributes, large block numbers, no debug enabled SGI XFS Quota Management subsystem device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@xxxxxxxxxxxxxx parport0: PC-style at 0x378 [PCSPP,TRISTATE] program anaconda is using a deprecated SCSI ioctl, please convert it to SG_IO program anaconda is using a deprecated SCSI ioctl, please convert it to SG_IO Device not ready. Make sure there is a disc in the drive. Device not ready. Make sure there is a disc in the drive. Device not ready. Make sure there is a disc in the drive. Device not ready. Make sure there is a disc in the drive. VFS: Can't find ext2 filesystem on dev sdb1. Unable to identify CD-ROM format. cramfs: wrong magic SELinux: initialized (dev sdb1, type vfat), uses genfs_contexts ======================================================================== == -----Original Message----- From: ataraid-list-bounces@xxxxxxxxxx [mailto:ataraid-list-bounces@xxxxxxxxxx] On Behalf Of hirac.kasapoglu@xxxxxxxxxxxxxxx Sent: Thursday, March 03, 2005 2:00 PM To: molle.bestefich@xxxxxxxxx; ataraid-list@xxxxxxxxxx Subject: RE: *** Announcement: dmraid 1.0.0.rc6 *** Call for testers Thank you for reply. Luckly I'm using RAID0, so no problem with RAID1 is broken :) But link http://tienstra4.flatnet.tudelft.nl/~gerte/gen2dmraid/ is broken ;) I'll try with FC3 installation CD and let you know the progress. Regards Hirac -----Original Message----- From: Molle Bestefich [mailto:molle.bestefich@xxxxxxxxx] Sent: Thursday, March 03, 2005 12:04 PM To: ataraid-list@xxxxxxxxxx Cc: HIRAC KASAPOGLU Subject: Re: *** Announcement: dmraid 1.0.0.rc6 *** Call for testers hirac.kasapoglu@xxxxxxxxxxxxxxx wrote: > Hello, I would like to be a tester. > But I need help to install linux in my system. > My system is: > - Shuttle SB81PIntel 915G chipset > (with Intel Soft RAID - Intel Matrix Storage called by Intel) > - Intel P4 2.8 Ghz LGA775512 MB RAM > - 2 x 160 GB Seagate SATA disk > (Configured as single RAID 0 disk) > I created following partitions on my RAID 0: > Primary Partition 1: 10 GB NTFS: Windows XP Installed [...] > Primary Partition 2: 290 GB Extended Partition > Logical Partition 1: 10 GB ext2 fs > Logical Partition 2: 1 GB swap partition > Logical Partition 3: 279 GB NTFS: Windows D drive > I created linux ext2 and swap partitions with Partition Magic. > Interestingly when I start windows 98SE installation CD without any RAID > driver, I can see RAID drive partitions, and I can partition the disk with > Partition Magic. That is because the RAID BIOS simulates a single disk. It does this by hooking a software interrupt known as INT13. Boot loaders, DOS, Windows and a bunch of other stuff uses this interrupt to access the disk. Therefore, they only see 1 disk, although it is really a RAID array. The INT13 calls are "stacked". This means that the software that your RAID BIOS hooks into INT13 checks to see if a request made is to one of the disks it is simulating. In case it is to a different (non-RAID or on a different controller) disk, it just calls the old handler, which is "lower in the stack". So much for that. Under Linux, only the boot loader generally uses INT13. The boot loader just loads the kernel. In order for disk accesses to be fast and more sophisticated, the kernel has it's own disk access mechanism, which resides in something you could call a IDE hardware driver module or whatever you fancy. I think Windows might have a fallback mechanism, so that it uses INT13 in case it can't find a driver, but really, I'm not sure. Perhaps only in Safe Mode. > But I cannot install Windows XP and Linux without RAID drivers. Ok. > When I try to install FC3, it cannot find any hard drive, and aborts the > installation. So how can I install FC3 to my Logical Partition 2? In the installer, you can break out into a shell by pressing CTRL-ALT-F2. Once in the shell, type "dd if=/dev/hda of=test count=1". If the hardware driver needed to access your disks is correctly in place, this should succeed. The driver might not be loaded until right before the 'disk partition' step is reached in the installer, so perhaps you need to click 'next' a couple of times before opening the shell. Once you've established that the hardware driver is in place, you need to have a piece of software that reads RAID metadata from the two physical disks and simulates one disk on top of the hardware driver. This software is dmraid. I've got no idea if dmraid is included with Fedora Core 3, but it's RedHat, so perhaps. Otherwise, download the DMRAID LiveCD generously provided by Gerte Hoogewerf. You should be able to download it here: http://tienstra4.flatnet.tudelft.nl/~gerte/gen2dmraid/ Unfortunately, it won't install anything. And you can't test RAID1. RAID1 in dmraid is broken anyway, at least for HighPoint controllers. ************************************************************************ Bu elektronik posta ve onunla iletilen butun dosyalar sadece gondericisi tarafindan almasi amaclanan yetkili gercek ya da tuzel kisinin kullanimi icindir. Eger soz konusu yetkili alici degilseniz bu elektronik postanin icerigini aciklamaniz, kopyalamaniz, yonlendirmeniz ve kullanmaniz kesinlikle yasaktir ve bu elektronik postayi derhal silmeniz gerekmektedir. TURKCELL bu mesajin icerdigi bilgilerin dogrulugu veya eksiksiz oldugu konusunda herhangi bir garanti vermemektedir. Bu nedenle bu bilgilerin ne sekilde olursa olsun iceriginden, iletilmesinden, alinmasindan ve saklanmasindan sorumlu degildir. Bu mesajdaki gorusler yalnizca gonderen kisiye aittir ve TURKCELLin goruslerini yansitmayabilir Bu e-posta bilinen butun bilgisayar viruslerine karsi taranmistir. ************************************************************************ This e-mail and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you are not the intended recipient you are hereby notified that any dissemination, forwarding, copying or use of any of the information is strictly prohibited, and the e-mail should immediately be deleted. TURKCELL makes no warranty as to the accuracy or completeness of any information contained in this message and hereby excludes any liability of any kind for the information contained therein or for the information transmission, reception, storage or use of such in any way whatsoever. The opinions expressed in this message belong to sender alone and may not necessarily reflect the opinions of TURKCELL. This e-mail has been scanned for all known computer viruses. ************************************************************************
