Re: Promise PDC20267 problems

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Do you have ext3 support built in the kernel ? Looks like you are using
initrd, is your Linux OS in the Promise FastTrak disks ?

On Tue, 8 Apr 2003, Tiit Kaeeli wrote:

> Hello,
> 
> I am using Intel SE7500CW2 motherboard with on-board Promise PDC20267
> FastTrak 100 IDE Raid controller and trying to get 2.4.21-pre6 kernel up
> and running with it. System is RedHat 7.3. When I boot my new kernel, I
> get following errors after
>         Mounting root filesystem in read-write mode     [OK]
> and some more [OK]- s:
> 
>         Finding module dependencies: execvp: Input/output error
>         EXT3-fs error (device ataraid(114,2)): read_inode_bitmap: Cannot
> read
>         inode bitmap - block_group=<number>
> 
> Following many more errors like that with different block_group numbers
> (Sorry, theese are only notes on paper)
> 
> I also tried RedHat kernel 2.4.20-8 and got the same errors. Kernel
> configuration file is kernel-2.4.20-i686-smp.config from RedHat 2.4.20-8
> source tree, only made modifications noted in Murty Rompalli-s Linux ATA
> RAID HOWTO. With older kernels I got lost IRQ errors, but according to
> /proc/pci PDC20267 is not sharing its IRQ with any other device. I found
> postings saying that there is a bug in kernels prior 2.4.21 causing this
> bahavior, so I decided to try 2.4.21
> 
> my /etc/lilo.conf:
> 
> prompt
> timeout=500
> default=2.4.18-3smp
> boot=/dev/sda
> map=/boot/map
> install=/boot/boot.b
> message=/boot/message
> lba32
> 
> image=/boot/vmlinuz-2.4.18-3smp
>         label=2.4.18-3smp
>         initrd=/boot/initrd-2.4.18-3smp.img
>         read-only
>         root=/dev/sda2
>         append="hda=ide-scsi"
> 
> image=/boot/vmlinuz-2.4.21-pre6
>         label=2.4.21-pre6
>         initrd=/boot/initrd-2.4.21-pre6.img
>         read-only
>         root=/dev/ataraid/d0p2
>         append="hda=ide-scsi"
> 
> image=/boot/vmlinuz-2.4.20-8custom
>         label=2.4.20-8custom
>         initrd=/boot/initrd-2.4.20-8custom.img
>         read-only
>         root=/dev/ataraid/d0p2
>         append="hda=ide-scsi"
> 
> Do I have to use append line? ATA RAID HOWTO talks about append line only
> when adding new non-os disks?
> 
> Any ideas?
> 
> 
> 
> 
> --
> 
> Tiit Kaeeli
> tiit_k@xxxxx
> 
> 
> 
> _______________________________________________
> 
> Ataraid-list@xxxxxxxxxx
> https://listman.redhat.com/mailman/listinfo/ataraid-list
> 





[Index of Archives]     [Linux RAID]     [Linux Device Mapper]     [Linux IDE]     [Linux SCSI]     [Kernel]     [Linux Books]     [Linux Admin]     [GFS]     [RPM]     [Yosemite Campgrounds]     [AMD 64]

  Powered by Linux