But if anyone could get the TX4, my raid would run faster and I could add another 400GB.
Shawn :-)
----Original Message Follows---- From: Jeremy Worrells <jworrells@xxxxxxxxxxxxx> Reply-To: ataraid-list@xxxxxxxxxx To: ataraid-list@xxxxxxxxxx Subject: Problem - IRQ timeouts with Promise TX4 Date: Mon, 7 Jan 2002 15:36:27 -0700
Hello everyone.
First of all, thank all of you that have worked on this driver.
Now, the problem. I installed a TX4 into my Dell PowerEdge 1300 and am having IRQ timeout problems. I'm not sure if it is a RAID driver issue or an ATA driver issue, but I thought I'd start here.
When booting, I get the following:
PDC20268: IDE controller on PCI bus 03 dev 08
PDC20268: chipset revision 2
PDC20268: not 100% native mode: will probe irqs later
PDC20268: ROM enabled at 0xf8000000
PDC20268: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary MASTER Mode.
ide2: BM-DMA at 0xccc0-0xccc7, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xccc8-0xcccf, BIOS settings: hdg:pio, hdh:pio
PDC20268: IDE controller on PCI bus 03 dev 10
PDC20268: chipset revision 2
PDC20268: not 100% native mode: will probe irqs later
PDC20268: ROM enabled at 0x000dc000
PDC20268: (U)DMA Burst Bit DISABLED Primary PCI Mode Secondary PCI Mode.
PDC20268: FORCING BURST BIT 0x00 -> 0x01 ACTIVE
ide4: BM-DMA at 0xccb0-0xccb7, BIOS settings: hdi:pio, hdj:pio
ide5: BM-DMA at 0xccb8-0xccbf, BIOS settings: hdk:pio, hdl:pio
hdc: SAMSUNG SC-140B, ATAPI CD/DVD-ROM drive
hde: WDC WD400BB-75CLB0, ATA DISK drive
hdg: WDC WD400BB-75CLB0, ATA DISK drive
hdi: WDC WD400BB-75CLB0, ATA DISK drive
hdk: WDC WD400BB-75CLB0, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xccf8-0xccff,0xccf2 on irq 20
ide3 at 0xcce0-0xcce7,0xccda on irq 20
ide4 at 0xcce8-0xccef,0xccf6 on irq 21
ide5 at 0xccd0-0xccd7,0xccde on irq 21
hde: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=77545/16/63, UDMA(100)
hdg: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=77545/16/63, UDMA(100)
hdi: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=77545/16/63, UDMA(100)
hdk: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=77545/16/63, UDMA(100)
hdc: ATAPI 40X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Partition check:
hde: [PTBL] [4865/255/63] hde1
hdg: [PTBL] [4865/255/63] hdg1
hdi:hdi: lost interrupt
hdi: lost interrupt
hdi: lost interrupt
PDC202XX: Primary channel reset.
ide_dmaproc: chipset supported ide_dma_lostirq func only: 13
hdi: lost interrupt
[PTBL] [4865/255/63] hdi1
hdk:hdk: lost interrupt
hdk: lost interrupt
hdk: lost interrupt
PDC202XX: Secondary channel reset.
ide_dmaproc: chipset supported ide_dma_lostirq func only: 13
hdk: lost interrupt
[PTBL] [4865/255/63] hdk1The first two drives get seen just fine, but hdi and hdk fall over. I cannot do anything with the array after booting.
I suspect it's an IRQ problem, but am not sure.
CPU0 CPU1 0: 52174 46311 IO-APIC-edge timer 1: 2 3 IO-APIC-edge keyboard 2: 0 0 XT-PIC cascade 15: 4 3 IO-APIC-edge ide1 16: 6510 6349 IO-APIC-level aic7xxx 20: 5429862 5429865 IO-APIC-level ide2, ide3 21: 0 0 IO-APIC-level ide4, ide5 22: 10682 10451 IO-APIC-level eth0 NMI: 0 0 LOC: 97554 98198 ERR: 0 MIS: 0
It's mystifying me, and my patience is growing short with this.
I have looked on google, but nothing pops up.
Can anyone help?
Jeremy -- Jeremy Worrells jworrells@xxxxxxxxxxxxx 801.270.8616
_______________________________________________ Ataraid-list@xxxxxxxxxx https://listman.redhat.com/mailman/listinfo/ataraid-list
_________________________________________________________________ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp.
