Hello everyone.
I have a problem. I have a callbycall number routet to our E1 Server.
If i Dial from my ISDN Phone to this callbycall number the call only
get acceptet if i press # key. Normal dial in and out works on our
server just if dial with call by call it did not work.
I Use
Sangoma A104 Card (Only 1 Port is Used)
Asterisk 1.8.9.3
Dahdi 2.6
chan_ss7 2.1.0
Wanpipe 3.5.25
dahdi systems.conf
#autogenerated by /usr/sbin/wancfg_dahdi do not hand edit
#autogenrated on 2012-03-02
#Dahdi Channels Configurations
#For detailed Dahdi options, view /etc/dahdi/system.conf.bak
loadzone=de
defaultzone=de
#Sangoma A104 port 1 [slot:3 bus:13 span:1] <wanpipe1>
span=1,0,0,ccs,hdb3,crc4
bchan=1-31
echocanceller=mg2,2-31
#hardhdlc=1
wanpipe1.conf
#================================================
# WANPIPE1 Configuration File
#================================================
#
# Date: Wed Dec 6 20:29:03 UTC 2006
#
# Note: This file was generated automatically
# by /usr/local/sbin/setup-sangoma program.
#
# If you want to edit this file, it is
# recommended that you use wancfg program
# to do so.
#================================================
# Sangoma Technologies Inc.
#================================================
[devices]
wanpipe1 = WAN_AFT_TE1, Comment
[interfaces]
w1g1 = wanpipe1, , TDM_VOICE, Comment
[wanpipe1]
CARD_TYPE = AFT
S514CPU = A
CommPort = PRI
AUTO_PCISLOT = NO
PCISLOT = 3
PCIBUS = 13
FE_MEDIA = E1
FE_LCODE = HDB3
FE_FRAME = CRC4
FE_LINE = 1
TE_CLOCK = MASTER
TE_REF_CLOCK = 0
TE_SIG_MODE = CCS
TE_HIGHIMPEDANCE = NO
TE_RX_SLEVEL = 430
HW_RJ45_PORT_MAP = DEFAULT
LBO = 120OH
FE_TXTRISTATE = NO
MTU = 1500
UDPPORT = 9000
TTL = 255
IGNORE_FRONT_END = NO
TDMV_SPAN = 1
TDMV_DCHAN = 0
TE_AIS_MAINTENANCE = NO #NO: defualt YES: Start port in AIS
Blue Alarm and keep line down
#wanpipemon -i w1g1 -c Ttx_ais_off to
disable AIS maintenance mode
#wanpipemon -i w1g1 -c Ttx_ais_on to enable AIS maintenance mode
TDMV_HW_DTMF = NO # YES: receive dtmf events from hardware
TDMV_HW_FAX_DETECT = NO # YES: receive fax 1100hz events from hardware
HWEC_OPERATION_MODE = OCT_NORMAL # OCT_NORMAL: echo cancelation
enabled with nlp (default)
# OCT_SPEECH: improves software tone detection by disabling
NLP (echo possible)
# OCT_NO_ECHO:disables echo cancelation but allows VQE/tone
functions.
HWEC_DTMF_REMOVAL = NO # NO: default YES: remove dtmf out of
incoming media (must have hwdtmf enabled)
HWEC_NOISE_REDUCTION = NO # NO: default YES: reduces noise on
the line - could break fax
HWEC_ACUSTIC_ECHO = NO # NO: default YES: enables acustic
echo cancelation
HWEC_NLP_DISABLE = NO # NO: default YES: guarantees
software tone detection (possible echo)
HWEC_TX_AUTO_GAIN = 0 # 0: disable -40-0: default tx audio
level to be maintained (-20 default)
HWEC_RX_AUTO_GAIN = 0 # 0: disable -40-0: default tx audio
level to be maintained (-20 default)
HWEC_TX_GAIN = 0 # 0: disable -24-24: db values to be
applied to tx signal
HWEC_RX_GAIN = 0 # 0: disable -24-24: db values to be
applied to tx signal
[w1g1]
ACTIVE_CH = ALL
TDMV_HWEC = NO
MTU = 8
ss7.conf
[linkset-siuc]
enabled => yes
enable_st => no
use_connect => no
hunting_policy => even_mru
context => ss7
language => de
t35 => 4000,st
subservice => auto
variant => ITU
[link-l1]
linkset => siuc
channels => 2-31
schannel => 1
firstcic => 1
enabled => yes
sltm => no
sls=0
echocancel => no
echocan_train => 350
echocan_taps => 128
[host-SS7-1]
if-1 => 10.1.40.71
enabled => yes
opc => 1601
dpc => siuc:300
links => l1:1 ;span 1 of dahdi/system.conf
;globaltitle => 0x00, 0x03, 0x01, 7773
ssn => 7
Anyone got an idea about this?
Greetings
Simon
|