hi i have problems with chan_ss7 to work with EWSD . i have tried many configuration with and without crc4, with different clock sources without success, i always get NOT_ALIGNED message i have also tried ss7 dump, but there wasn't any output many thanks for any help, and sorry for my english ;) ############status dmesg ADDRCONF(NETDEV_CHANGE): w1g1: link becomes ready wanpipe1: Global TDM Ring Resync wanpipe1: Card TDM Rsync Rx=0 Tx=2 wanpipe1: RAI alarm is OFF wanpipe1: OOF alarm is OFF mtrr: type mismatch for f9000000,800000 old: write-back new: write-combining voicegw*CLI> ss7 link status linkset siuc, link l1, schannel 1, sls 0, NOT_ALIGNED, rx: 0, tx: 4/4, sentseq/lastack: 127/127, total 4754816, 4754912v i am also getting this message WARNING[4390]: mtp.c:513 t2_timeout: MTP2 timer T2 timeout (failed to receive 'O', 'N', or 'E' after sending 'O'), initial alignment failed on link 'l1'. here are my configs #dahdi system.conf #autogenerated by /usr/sbin/wancfg_dahdi do not hand edit #autogenrated on 2009-06-03 #Dahdi Channels Configurations #For detailed Dahdi options, view /etc/dahdi/system.conf.bak loadzone=us defaultzone=us #Sangoma A108 port 1 [slot:4 bus:3 span:1] <wanpipe1> span=1,1,0,ccs,hdb3,crc4 #span=1,0,0,ccs,hdb3 bchan=1-31 wanpipe1.conf #================================================ # WANPIPE1 Configuration File #================================================ # # Date: Wed Dec 6 20:29:03 UTC 2006 # # Note: This file was generated automatically # by /usr/local/sbin/setup-sangoma program. # # If you want to edit this file, it is # recommended that you use wancfg program # to do so. #================================================ # Sangoma Technologies Inc. #================================================ [devices] wanpipe1 = WAN_AFT_TE1, Comment [interfaces] w1g1 = wanpipe1, , TDM_VOICE, Comment [wanpipe1] CARD_TYPE = AFT S514CPU = A CommPort = PRI AUTO_PCISLOT = NO PCISLOT = 4 PCIBUS = 3 FE_MEDIA = E1 FE_LCODE = HDB3 FE_FRAME = CRC4 FE_LINE = 1 TE_CLOCK = NORMAL TE_REF_CLOCK = 0 TE_SIG_MODE = CCS TE_HIGHIMPEDANCE = NO LBO = 120OH FE_TXTRISTATE = NO MTU = 1500 UDPPORT = 9000 TTL = 255 IGNORE_FRONT_END = NO TDMV_SPAN = 1 TDMV_DCHAN = 16 TDMV_HW_DTMF = YES TDMV_HW_FAX_DETECT = NO [w1g1] ACTIVE_CH = ALL TDMV_HWEC = YES ss7.conf [linkset-siuc] ; The linkset is enabled enabled => yes ; The end-of-pulsing (ST) is not used to determine when incoming address is complete enable_st => no ; Reply incoming call with CON rather than ACM and ANM use_connect => yes ; The CIC hunting policy (even_mru, odd_lru, seq_lth, seq_htl) is even CIC numbers, most recently used hunting_policy => even_mru ; Incoming calls are placed in the ss7 context in the asterisk dialplan context => ss7 ; The language for this context is da language => da ; The value and action for t35. Value is in msec, action is either st or timeout ; If you use overlapped dialling dial plan, you might choose: t35 => 4000,st t35 => 15000,timeout ; The subservice field: national (8), international (0), auto or decimal/hex value ; The auto means that the subservice is obtained from first received SLTM subservice => auto ; The host running the mtp3 service ; mtp3server => localhost [link-l1] ; This link belongs to linkset siuc linkset => siuc ; The speech/audio circuit channels on this link channels => 2-31 ; The signalling channel schannel => 1 ;yes i have signalling on channel 1, with libss7 was working (configs for libss7 are included lower)) ; To use the remote mtp3 service, use 'schannel => remote,16' ; The first CIC firstcic => 1 ;;i have also tried start with firstcic =>2 ; The link is enabled enabled => yes ; Echo cancellation ; echocancel can be one of: no, 31speech (enable only when transmission medium is 3.1Khz speech), allways echocancel => no ; echocan_train specifies training period, between 10 to 100 msec echocan_train => 350 ; echocan_taps specifies number of taps, 32, 64, 128 or 256 echocan_taps => 128 [host-voicegw] ; chan_ss7 auto-configures by matching the machines host name with the host-<name> ; section in the configuration file, in this case 'gentoo1'. The same ; configuration file can thus be used on several hosts. ; The host is enabled enabled => yes ; The point code for this SS7 signalling point is 0x8e0 ;opc => 0x8e0 ; 15389 dec opc => 0x3c1d ; The destination point (peer) code is 0x3fff for linkset siuc ;dpc => siuc:0x3fff ; 15880 dpc => siuc:0x3e08 ; Syntax: links => link-name:digium-connector-no ; The links on the host is 'l1', connected to span/connector #1 links => l1:1 ; The SCCP global title: translation-type, nature-of-address, numbering-plan, address globaltitle => 0x00, 0x04, 0x01, 4546931411 ssn => 7 ## [root at voicegw ~]# uname -a Linux voicegw 2.6.18-128.el5 #1 SMP Wed Dec 17 11:41:38 EST 2008 x86_64 x86_64 x86_64 GNU/Linux ################################### this is working configuration for linss7, it was good, but there were some problems with ss7 stack ##chan_dahdi.conf trunkgroup => 1,1 spanmap => 1,1 language=en context=ss7 switchtype=euroisdn pridialplan=unknown prilocaldialplan=national usecallerid=yes callwaiting=yes usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes canpark=yes cancallforward=yes callreturn=yes echocancel=yes echocancelwhenbridged=yes group=1 callgroup=1 pickupgroup=1 ss7_called_nai=dynamic ss7_calling_nai=dynamic ss7_internationalprefix = 00 ss7_nationalprefix = 0 ss7_subscriberprefix = ss7_unknownprefix = networkindicator=national_spare signalling = ss7 ss7type = itu linkset = 1 pointcode = 15389 adjpointcode = 15880 defaultdpc = 15880 cicbeginswith = 2 channel=2-31 sigchan = 1 ##system.conf span=1,1,0,ccs,hdb3,crc4 bchan=2-31 #echocanceller=mg2,2-31 mtp2=1