Hi,
I am having trouble with two issues here.
1. Is there any winpipe version that supports DAHDI?
2.
With zaptel installed, I can't get my channels configured:
root at localhost etc]# ztcfg -vv
Zaptel Version: 1.4.12.1
Echo Canceller: MG2
Configuration
======================
SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
Channel map:
Channel 01: Clear channel (Default) (Slaves: 01)
Channel 02: Clear channel (Default) (Slaves: 02)
Channel 03: Clear channel (Default) (Slaves: 03)
Channel 04: Clear channel (Default) (Slaves: 04)
Channel 05: Clear channel (Default) (Slaves: 05)
Channel 06: Clear channel (Default) (Slaves: 06)
Channel 07: Clear channel (Default) (Slaves: 07)
Channel 08: Clear channel (Default) (Slaves: 08)
Channel 09: Clear channel (Default) (Slaves: 09)
Channel 10: Clear channel (Default) (Slaves: 10)
Channel 11: Clear channel (Default) (Slaves: 11)
Channel 12: Clear channel (Default) (Slaves: 12)
Channel 13: Clear channel (Default) (Slaves: 13)
Channel 14: Clear channel (Default) (Slaves: 14)
Channel 15: Clear channel (Default) (Slaves: 15)
Channel 16: D-channel (Default) (Slaves: 16)
Channel 17: Clear channel (Default) (Slaves: 17)
Channel 18: Clear channel (Default) (Slaves: 18)
Channel 19: Clear channel (Default) (Slaves: 19)
Channel 20: Clear channel (Default) (Slaves: 20)
Channel 21: Clear channel (Default) (Slaves: 21)
Channel 22: Clear channel (Default) (Slaves: 22)
Channel 23: Clear channel (Default) (Slaves: 23)
Channel 24: Clear channel (Default) (Slaves: 24)
Channel 25: Clear channel (Default) (Slaves: 25)
Channel 26: Clear channel (Default) (Slaves: 26)
Channel 27: Clear channel (Default) (Slaves: 27)
Channel 28: Clear channel (Default) (Slaves: 28)
Channel 29: Clear channel (Default) (Slaves: 29)
Channel 30: Clear channel (Default) (Slaves: 30)
Channel 31: Clear channel (Default) (Slaves: 31)
31 channels to configure.
[root at localhost asterisk]# cat /proc/zaptel/1
Span 1: WPE1/0 "wanpipe1 card 0" (MASTER) HDB3/CCS/CRC4 RED
1 WPE1/0/1 Clear RED
2 WPE1/0/2 Clear RED
3 WPE1/0/3 Clear RED
4 WPE1/0/4 Clear RED
5 WPE1/0/5 Clear RED
6 WPE1/0/6 Clear RED
7 WPE1/0/7 Clear RED
8 WPE1/0/8 Clear RED
9 WPE1/0/9 Clear RED
10 WPE1/0/10 Clear RED
11 WPE1/0/11 Clear RED
12 WPE1/0/12 Clear RED
13 WPE1/0/13 Clear RED
14 WPE1/0/14 Clear RED
15 WPE1/0/15 Clear RED
16 WPE1/0/16 HDLCFCS RED
17 WPE1/0/17 Clear RED
18 WPE1/0/18 Clear RED
19 WPE1/0/19 Clear RED
20 WPE1/0/20 Clear RED
21 WPE1/0/21 Clear RED
22 WPE1/0/22 Clear RED
23 WPE1/0/23 Clear RED
24 WPE1/0/24 Clear RED
25 WPE1/0/25 Clear RED
26 WPE1/0/26 Clear RED
27 WPE1/0/27 Clear RED
28 WPE1/0/28 Clear RED
29 WPE1/0/29 Clear RED
30 WPE1/0/30 Clear RED
31 WPE1/0/31 Clear RED
ifconfig:
w1g1 Link encap:Point-to-Point Protocol
UP POINTOPOINT NOARP MTU:8 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:58 Memory:f8d30000-f8d31fff
[root at localhost asterisk]# wanrouter status
Devices currently active:
wanpipe1
Wanpipe Config:
Device name | Protocol Map | Adapter | IRQ | Slot/IO | If's | CLK | Baud
rate |
wanpipe1 | N/A | A101/1D/A102/2D/4/4D/8| 58 | 1 | 1 |
N/A | 0 |
Wanrouter Status:
Device name | Protocol | Station | Status |
wanpipe1 | AFT TE1 | N/A | Connecting |
Any suggestion or hint will be greatly appreciated.
Thanks,
Mark
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-ss7/attachments/20081005/c0955f7e/attachment.htm
|