Hello. You may consider the portable SS7 protocol analyzer/simulator from Utel Systems for Asterisk debugging. SS7 analyzers and simulators for both SS7oTDM (E1/T1) and SS7oIP are available. Other protocol analyzers and simulators for ISDN PRI, SIP, SIP-T, SIGTRAN, Megaco etc. are also available. More information: www.utelsystems.com Best regards, Frode -----Original Message----- From: asterisk-ss7-bounces@xxxxxxxxxxxxxxxx [mailto:asterisk-ss7-bounces@xxxxxxxxxxxxxxxx] On Behalf Of Ercan Y?cebas Sent: 23. mars 2007 14:15 To: asterisk-ss7@xxxxxxxxxxxxxxxx Subject: RE: ISUP Debugging HOWTO Hello Andreas Yesterday finally i find out, that this behaviour - sending or not sending ACM after IAM - can be controlled with the variable use_connect, it was on my system setted as "yes" and therefore my chan_ss7 don't sended out ACM, which caused that my provider sends me rigt a way a REL, because ACM is needed and can't be replaced just by CPG, at least not here in Switzerland :) I seen in the code, that the value of this variable in ss7.conf is controlling this behaviour. Now I changed the value and this issue is solved for me. Thank you so much for your interest BR Ercan -----Original Message----- From: asterisk-ss7-bounces@xxxxxxxxxxxxxxxx [mailto:asterisk-ss7-bounces@xxxxxxxxxxxxxxxx] On Behalf Of Anders Baekgaard Sent: Freitag, 23. M?rz 2007 10:03 To: asterisk-ss7@xxxxxxxxxxxxxxxx Subject: Re: ISUP Debugging HOWTO Hello Ercan, I've seen reports about the the ACM/CPG problem, but I've not been able to reproduce it. Please, can you send me the PDU dump together with the relevant part of your dial plan, and the asterisk debug log. Best regards Anders Baekgaard On Thursday 22 March 2007 21:35, Ercan Y?cebas wrote: > Dear Kristian > > It helped me too much, now i'm realy sure that my chan_ss7 doesn't send > ACM after an IAM. It just sending directly CPG Alerting. > > This behaviour isn't in ITU standarts and therefore the incumbend > telecom operator here in Switzerland rejects there calls and sends > inmediatelly an REL. chan_ss7 answers to that with an RLC as also > expected. > > So I have to find out now, under which conditions chan_ss7 wants to send > an ACM etc...... > > > Thanks again a lot > > BR > Ercan > > > > > -----Original Message----- > From: asterisk-ss7-bounces@xxxxxxxxxxxxxxxx > [mailto:asterisk-ss7-bounces@xxxxxxxxxxxxxxxx] On Behalf Of Kristian > Nielsen > Sent: Donnerstag, 22. M?rz 2007 13:03 > To: asterisk-ss7@xxxxxxxxxxxxxxxx > Subject: Re: [asterisk-ss7] ISUP Debugging HOWTO > > Ercan Y?cebas <ercan@xxxxxxxxxxxxxx> writes: > > I need to find out what is happening here with ss7 signaling. How can > > I > > > just debug the isup signalling messages? > > ss7 dump start isup-debug.log both msu > > See here for more info: > > http://voip-info.org/wiki/index.php?page=Asterisk+ss7+commands > > - Kristian. _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-ss7 mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-ss7 _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-ss7 mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-ss7
|