First of all, it looks like you are either loading chan_zap.so twice, or you have something else that has tried to open the zap channels (maybe chan_ss7.so?). So you need to get that straightened out. I would remove the contents of /usr/lib/asterisk/modules and do a make install from your asterisk-trunk directory again. Second, your lines in your zapata.conf that are supposed to be adjpointcode= look like they are set to djpointcode= instead (Unless that was a copy/paste error). That would be the reason it is failing at that point. Matthew Fredrickson ----- umar tarar <umar.tarar@xxxxxxxxx> wrote: > yes u r right, & i myself had discovered this prob, & i infact posted > two further posts after the one that u(Matt.) responded, but don't > know y did'nt those two posts get on to the asterisk-ss7 lists right > after my previouse post. ok here r those: > > ############post-1############ > lately i've discovered that after compiling asterisk-trunk, i dont > have any chan_zap.so file in my /usr/lib/asterisk/modules/, that is y > asterisk while running is unable to load the chan_zap.so & because of > it, it do not do anything about zap, ....am i right? > if yes then what should i do to correctly compile the asterisk-trunk > to get the chan_zap.so (i already have tried make & make install twice > but did'nt get chan_zap.so both times in my > /usr/lib/asterisk/modules/, though chan_zap.c is present in > asterisk-trunk folder) > ############################# > > ###########post-2############# > okay Matt.! now some how after fixing that chan_zap.so prob (by > rechecking once again all the three packages), now when i run the > asterisk with forcefully loading the chan_zap.so modules by loading it > into modules.conf , it gives the following error about djpointcode & > sigchan as; > > ------------CLI eror log----------------- > . > . > [ Oct 14 07:28:18 ] NOTICE[4070]: loader.c:793 load_modules: 1 modules > will be loaded. > == Registered application 'ZapSendKeypadFacility' > == Parsing '/etc/asterisk/zapata.conf': Found > [ Oct 14 07:28:18 ] ERROR[4070]: chan_zap.c:11272 linkset_addsigchan: > Unspecified adjpointcode! > . > . > . > res_features.so => (Call Features Resource) > == Parsing '/etc/asterisk/smdi.conf': Found > [ Oct 14 07:28:18 ] WARNING[4070]: res_smdi.c:726 load_module: No SMDI > interfaces are available to listen on, not starting SDMI listener. > [ Oct 14 07:28:18 ] WARNING[4070]: pbx.c:2818 > ast_register_application: Already have an application > 'ZapSendKeypadFacility' > == Parsing '/etc/asterisk/zapata.conf': Found > [ Oct 14 07:28:18 ] ERROR[4070]: chan_zap.c:11222 linkset_addsigchan: > Unable to open SS7 sigchan 16 (Device or resource busy) > . > . > . > ---------------------------------------------- > > and here r my zapata.conf & zaptel.conf > > -----------------zapata.conf-------------- > channels] > context=zapIncoming > switchtype=euroisdn > usecallerid=yes > hidecallerid=no > echocancel=yes > echocancelwhenbridged=yes > musiconhold=default > > signalling = ss7 > ss7type = itu > > linkset = 1 > > ;pointcode = 0x1680 > pointcode = 05760 > > ;djpointcode = 0x168a > djpointcode = 05770 > ;djpointcode = 05-10-10 > > ;defaultdpc = 0x168a > djpointcode = 05770 > ;defaultdpc = 05-10-10 > > networkindicator=national > cicbeginswith = 1 > sigchan = 16 ; First signaling channel > channel=>1-15,17-31 > > ;channel=>1-15 > ;cicbeginswith=17 > ;channel=>17-31 > ----------------------------------------------- > > ---------------zaptel.conf----------------- > pan=1,1,0,ccs,hdb3 > bchan=1-15,17-31 > dchan=16 > ----------------------------------------------- > > now i think the problem is quite identified, so plz suggest me what > should i do to solve this > ############################# > > so plz now respond according to having these two posts right after my > previous post (in which i've already mentioned, what the CLI error log > says abt zap --- keep in mind that chan_zap.so did'nt load > autometically rather i forcefully loaded it through 'load' command in > modules.conf) > > waitin for the responces > > > > On 10/14/06 , Matt Fredrickson < creslin@xxxxxxxxxx > wrote: It sounds > like chan_zap.so didn't load... You need to look at what happens when > you load asterisk, to see why chan_zap.so is not loading. > > Matthew Fredrickson
|