Re: X fails to start with intel card after latestkernel update

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]



On Thursday 15 October 2009 07:47:11 am pascal wrote:
> Hi
> In the last Xorg.0.log I can see that you removed the "vga=0x31a" part. But
> the vesa module is still loaded (and unloaded short after) just after the
>  intel module, and the output used is VGA1. I also have an 915 chipset
>  (though a 915GM) and upgraded to Xorg from testing to see if I could
>  reproduce your problem. Apart some serious performance regression (and
>  some freezes...) it works almost fine. I diff'ed my Xorg.0.log with yours
>  and I don't have the vesa module loaded. Also my output is set to LVDS1,
>  which I remember changed when I went to KMS some months ago (before that
>  the output was VGA1, if I record correctly). I also have a line saying "
>  (**) intel(0): Kernel mode setting active, disabling FBC. ", which doesn't
>  appear in your log. Makes me wonder if your kernel is really using KMS.
>  When booted, does the framebuffer display in native resolution ?
> I switched back to Xorg from [extra] for stability matters. [testing] being
> for ... well, testing.
> 

Pascal,

	Thank you for taking the time to help. I'm really stumped here. The funny 
thing is "Yes", even with all vga= lines removed, I get native resolution of 
what looks like 1280x1024 when the box boot. What happens is the box will boot 
and the first 20 or so lines is in 640x480, then magically the box switches to 
1280x1024. The actual resolution of the monitor is 1680x1050 when X starts 
(well when it used to start). I have never had this much trouble with X 
before.

	In answer to your second question "Yes" I have booted to runlevel 3 and tried 
to use startx -- same result. X tries to start then crashes. Here are some 
more hardware details in case that would help. The box is a dell gx280 with a 
P4-3.2GHz processor. The output of lspci is:

00:02.0 VGA compatible controller: Intel Corporation 82915G/GV/910GL 
Integrated Graphics Controller (rev 04) (prog-if 00 [VGA controller])                                                                                                      
        Subsystem: Dell Device 0179                                                                                     
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-           
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-            
        Latency: 0                                                                                                      
        Interrupt: pin A routed to IRQ 16                                                                               
        Region 0: Memory at dff00000 (32-bit, non-prefetchable) [size=512K]                                             
        Region 1: I/O ports at e898 [size=8]                                                                            
        Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M]                                                 
        Region 3: Memory at dfec0000 (32-bit, non-prefetchable) [size=256K]                                             
        Expansion ROM at <unassigned> [disabled]                                                                        
        Capabilities: [d0] Power Management version 2                                                                   
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)                              
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-                                                  
        Kernel driver in use: i915                                                                                      

00:02.1 Display controller: Intel Corporation 82915G Integrated Graphics 
Controller (rev 04)
        Subsystem: Dell Device 0179                                                         
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx- 
        Latency: 0                                                                                           
        Region 0: Memory at dff80000 (32-bit, non-prefetchable) [size=512K]                                  
        Capabilities: [d0] Power Management version 2                                                        
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)                   
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-                                       


Full output is here:

http://www.3111skyline.com/download/Archlinux/bugs/supersff/lspci.txt

dmidecode details are here:

http://www.3111skyline.com/download/Archlinux/bugs/supersff/dmidecode.txt

latest Xorg.0.log is here:

http://www.3111skyline.com/download/Archlinux/bugs/supersff/Xorg.0.log


If you have any other suggestions or ideas, please let me know. Thanks.

-- 
David C. Rankin, J.D.,P.E.
Rankin Law Firm, PLLC
510 Ochiltree Street
Nacogdoches, Texas 75961
Telephone: (936) 715-9333
Facsimile: (936) 715-9339
www.rankinlawfirm.com


[Index of Archives]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [Share Photos]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]
  Powered by Linux