Re: [PATCH v11] drm/amdgpu: add drm buddy support to amdgpu

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Am 29.03.22 um 21:18 schrieb Arunpravin Paneer Selvam:

On 29/03/22 9:30 pm, Arunpravin Paneer Selvam wrote:

On 29/03/22 4:54 pm, Christian König wrote:
Am 29.03.22 um 13:19 schrieb Arunpravin Paneer Selvam:
[SNIP]
+	pages_left = node->base.num_pages;
i = 0;
-	spin_lock(&mgr->lock);
    	while (pages_left) {
-		uint32_t alignment = tbo->page_alignment;
+		if (tbo->page_alignment)
+			min_page_size = tbo->page_alignment << PAGE_SHIFT;
+		else
+			min_page_size = mgr->default_page_size;
The handling here looks extremely awkward to me.

min_page_size should be determined outside of the loop, based on default_page_size, alignment and contiguous flag.
I kept min_page_size determine logic inside the loop for cases 2GiB+
requirements, Since now we are round up the size to the required
alignment, I modified the min_page_size determine logic outside of the
loop in v12. Please review.
Ah! So do we only have the loop so that each allocation isn't bigger
than 2GiB? If yes couldn't we instead add a max_alloc_size or something
similar?
yes we have the loop to limit the allocation not bigger than 2GiB, I
think we cannot avoid the loop since we need to allocate the remaining
pages if any, to complete the 2GiB+ size request. In other words, first
iteration we limit the max size to 2GiB and in the second iteration we
allocate the left over pages if any.
Hi Christian,

Here my understanding might be incorrect, should we limit the max size =
2GiB and skip all the remaining pages for a 2GiB+ request?

No, the total size can be bigger than 2GiB. Only the contained pages should be a maximum of 2GiB.

See drm_buddy_alloc_blocks() already has the loop you need inside of it, all you need to do is to restrict the maximum allocation order.

In other words you got this line here in drm_buddy_alloc_blocks:

order = fls(pages) - 1;

Which then would become:

oder = min(fls(pages), mm->max_order) - 1;

You then just need to give mm->max_order as parameter to drm_buddy_init() instead of trying to figure it out yourself. This would then also make the following BUG_ON() superfluous.

And btw: IIRC fls() uses only 32 bit! You should either use fls64() or directly ilog2() which optimizes and calls fls() or fls64() or constant log2 based on the data type.

Regards,
Christian.


Thanks,
Arun
BTW: I strongly suggest that you rename min_page_size to min_alloc_size.
Otherwise somebody could think that those numbers are in pages and not
bytes.
modified in v12
Then why do you drop the lock and grab it again inside the loop? And what is "i" actually good for?
modified the lock/unlock placement in v12.

"i" is to track when there is 2GiB+ contiguous allocation request, first
we allocate 2GiB (due to SG table limit) continuously and the remaining
pages in the next iteration, hence this request can't be a continuous.
To set the placement flag we make use of "i" value. In our case "i"
value becomes 2 and we don't set the below flag.
node->base.placement |= TTM_PL_FLAG_CONTIGUOUS;

If we don't get such requests, I will remove "i".
I'm not sure if that works.

As far as I can see drm_buddy_alloc_blocks() can allocate multiple
blocks at the same time, but i is only incremented when we loop.

So what you should do instead is to check if node->blocks just contain
exactly one element after the allocation but before the trim.
ok
+
+		/* Limit maximum size to 2GB due to SG table limitations */
+		pages = min(pages_left, 2UL << (30 - PAGE_SHIFT));
if (pages >= pages_per_node)
-			alignment = pages_per_node;
-
-		r = drm_mm_insert_node_in_range(mm, &node->mm_nodes[i], pages,
-						alignment, 0, place->fpfn,
-						lpfn, mode);
-		if (unlikely(r)) {
-			if (pages > pages_per_node) {
-				if (is_power_of_2(pages))
-					pages = pages / 2;
-				else
-					pages = rounddown_pow_of_two(pages);
-				continue;
-			}
-			goto error_free;
+			min_page_size = pages_per_node << PAGE_SHIFT;
+
+		if (!is_contiguous && !IS_ALIGNED(pages, min_page_size >> PAGE_SHIFT))
+			is_contiguous = 1;
+
+		if (is_contiguous) {
+			pages = roundup_pow_of_two(pages);
+			min_page_size = pages << PAGE_SHIFT;
+
+			if (pages > lpfn)
+				lpfn = pages;
    		}
- vis_usage += amdgpu_vram_mgr_vis_size(adev, &node->mm_nodes[i]);
-		amdgpu_vram_mgr_virt_start(&node->base, &node->mm_nodes[i]);
-		pages_left -= pages;
+		BUG_ON(min_page_size < mm->chunk_size);
+
+		mutex_lock(&mgr->lock);
+		r = drm_buddy_alloc_blocks(mm, (u64)place->fpfn << PAGE_SHIFT,
+					   (u64)lpfn << PAGE_SHIFT,
+					   (u64)pages << PAGE_SHIFT,
+					   min_page_size,
+					   &node->blocks,
+					   node->flags);
+		mutex_unlock(&mgr->lock);
+		if (unlikely(r))
+			goto error_free_blocks;
+
    		++i;
if (pages > pages_left)
-			pages = pages_left;
+			pages_left = 0;
+		else
+			pages_left -= pages;
    	}
-	spin_unlock(&mgr->lock);
- if (i == 1)
+	/* Free unused pages for contiguous allocation */
+	if (is_contiguous) {
Well that looks really odd, why is trimming not part of
drm_buddy_alloc_blocks() ?
we didn't place trim function part of drm_buddy_alloc_blocks since we
thought this function can be a generic one and it can be used by any
other application as well. For example, now we are using it for trimming
the last block in case of size non-alignment with min_page_size.
Good argument. Another thing I just realized is that we probably want to
double check if we only allocated one block before the trim.
ok
Thanks,
Christian.





[Index of Archives]     [Linux USB Devel]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux