Solve comments alignment problems on dc_link file
Signed-off-by: Melissa Wen <melissa.srw@xxxxxxxxx>
---
drivers/gpu/drm/amd/display/dc/core/dc_link.c | 25 +++++++++++--------
1 file changed, 15 insertions(+), 10 deletions(-)
diff --git a/drivers/gpu/drm/amd/display/dc/core/dc_link.c b/drivers/gpu/drm/amd/display/dc/core/dc_link.c
index 67cfff1586e9..f580b533db5f 100644
--- a/drivers/gpu/drm/amd/display/dc/core/dc_link.c
+++ b/drivers/gpu/drm/amd/display/dc/core/dc_link.c
@@ -64,11 +64,11 @@
enum {
PEAK_FACTOR_X1000 = 1006,
/*
- * Some receivers fail to train on first try and are good
- * on subsequent tries. 2 retries should be plenty. If we
- * don't have a successful training then we don't expect to
- * ever get one.
- */
+ * Some receivers fail to train on first try and are good
+ * on subsequent tries. 2 retries should be plenty. If we
+ * don't have a successful training then we don't expect to
+ * ever get one.
+ */
LINK_TRAINING_MAX_VERIFY_RETRY = 2
};
@@ -270,7 +270,8 @@ static enum ddc_transaction_type get_ddc_transaction_type(
case SIGNAL_TYPE_DISPLAY_PORT_MST:
/* MST does not use I2COverAux, but there is the
* SPECIAL use case for "immediate dwnstrm device
- * access" (EPR#370830). */
+ * access" (EPR#370830).
+ */
transaction_type = DDC_TRANSACTION_TYPE_I2C_OVER_AUX;
break;
@@ -369,7 +370,8 @@ bool dc_link_is_dp_sink_present(struct dc_link *link)
/* Open GPIO and set it to I2C mode */
/* Note: this GpioMode_Input will be converted
* to GpioConfigType_I2cAuxDualMode in GPIO component,
- * which indicates we need additional delay */
+ * which indicates we need additional delay
+ */
if (GPIO_RESULT_OK != dal_ddc_open(
ddc, GPIO_MODE_INPUT, GPIO_DDC_CONFIG_TYPE_MODE_I2C)) {
@@ -414,14 +416,16 @@ static enum signal_type link_detect_sink(
link->link_enc->id, link->link_id);
/* Internal digital encoder will detect only dongles
- * that require digital signal */
+ * that require digital signal
+ */
/* Detection mechanism is different
* for different native connectors.
* LVDS connector supports only LVDS signal;
* PCIE is a bus slot, the actual connector needs to be detected first;
* eDP connector supports only eDP signal;
- * HDMI should check straps for audio */
+ * HDMI should check straps for audio
+ */
/* PCIE detects the actual connector on add-on board */
@@ -432,7 +436,8 @@ static enum signal_type link_detect_sink(
switch (link->link_id.id) {
case CONNECTOR_ID_HDMI_TYPE_A: {
/* check audio support:
- * if native HDMI is not supported, switch to DVI */
+ * if native HDMI is not supported, switch to DVI
+ */
struct audio_support *aud_support = &link->dc->res_pool->audio_support;
if (!aud_support->hdmi_audio_native)
--
2.25.1
_______________________________________________
amd-gfx mailing list
amd-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/amd-gfx
