From: Nicholas Kazlauskas <nicholas.kazlauskas@xxxxxxx>
[Why]
If the cursor pos passed from DM is less than the plane_state->dst_rect
top left corner then the unsigned cursor pos wraps around to a large
positive number since cursor pos is a u32.
There was an attempt to guard against this in hubp1_cursor_set_position
by checking the src_x_offset and src_y_offset and offseting the
cursor hotspot within hubp1_cursor_set_position.
However, the cursor position itself is still being programmed
incorrectly as a large value.
This manifests itself visually as the cursor disappearing or containing
strange artifacts near the middle of the screen on raven.
[How]
Don't subtract the destination rect top left corner from the pos but
add it to the hotspot instead. This happens before the pos gets
passed into hubp1_cursor_set_position.
This achieves the same result but avoids the subtraction wrap around.
With this fix the original cursor programming logic can be used again.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@xxxxxxx>
Reviewed-by: Charlene Liu <Charlene.Liu@xxxxxxx>
Acked-by: Leo Li <sunpeng.li@xxxxxxx>
Acked-by: Murton Liu <Murton.Liu@xxxxxxx>
---
drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hubp.c | 23 ++--------------------
.../drm/amd/display/dc/dcn10/dcn10_hw_sequencer.c | 4 ++--
2 files changed, 4 insertions(+), 23 deletions(-)
diff --git a/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hubp.c b/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hubp.c
index 6838294..0ba68d4 100644
--- a/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hubp.c
+++ b/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hubp.c
@@ -1150,28 +1150,9 @@ void hubp1_cursor_set_position(
REG_UPDATE(CURSOR_CONTROL,
CURSOR_ENABLE, cur_en);
- //account for cases where we see negative offset relative to overlay plane
- if (src_x_offset < 0 && src_y_offset < 0) {
- REG_SET_2(CURSOR_POSITION, 0,
- CURSOR_X_POSITION, 0,
- CURSOR_Y_POSITION, 0);
- x_hotspot -= src_x_offset;
- y_hotspot -= src_y_offset;
- } else if (src_x_offset < 0) {
- REG_SET_2(CURSOR_POSITION, 0,
- CURSOR_X_POSITION, 0,
- CURSOR_Y_POSITION, pos->y);
- x_hotspot -= src_x_offset;
- } else if (src_y_offset < 0) {
- REG_SET_2(CURSOR_POSITION, 0,
+ REG_SET_2(CURSOR_POSITION, 0,
CURSOR_X_POSITION, pos->x,
- CURSOR_Y_POSITION, 0);
- y_hotspot -= src_y_offset;
- } else {
- REG_SET_2(CURSOR_POSITION, 0,
- CURSOR_X_POSITION, pos->x,
- CURSOR_Y_POSITION, pos->y);
- }
+ CURSOR_Y_POSITION, pos->y);
REG_SET_2(CURSOR_HOT_SPOT, 0,
CURSOR_HOT_SPOT_X, x_hotspot,
diff --git a/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.c b/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.c
index 8ba895c..d1a8f1c 100644
--- a/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.c
+++ b/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.c
@@ -2693,8 +2693,8 @@ static void dcn10_set_cursor_position(struct pipe_ctx *pipe_ctx)
.mirror = pipe_ctx->plane_state->horizontal_mirror
};
- pos_cpy.x -= pipe_ctx->plane_state->dst_rect.x;
- pos_cpy.y -= pipe_ctx->plane_state->dst_rect.y;
+ pos_cpy.x_hotspot += pipe_ctx->plane_state->dst_rect.x;
+ pos_cpy.y_hotspot += pipe_ctx->plane_state->dst_rect.y;
if (pipe_ctx->plane_state->address.type
== PLN_ADDR_TYPE_VIDEO_PROGRESSIVE)
--
2.7.4
_______________________________________________
amd-gfx mailing list
amd-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/amd-gfx
