Hi Christian,
I've been using a Sapphire RX 550 and a Sapphire RX 460 on a custom
armhf board that runs well with Linux 4.19.9 at least, but now
starting with Linux kernel 4.20, I'm having a gpu hang, right after
the console being displayed, but before entering in graphical mode,
when starting X session.
I'm only reporting this now, because there was a PCI commit for mvebu
that also entered for linux-4.20 that caused a kernel oops during
pci_map_rom call in amdgpu initialization code. I've reverted that
patch, but now amdgpu is hanging.
[ 24.801861] [drm:amdgpu_job_timedout [amdgpu]] *ERROR* ring gfx
timeout, signaled seq=2, emitted seq=3
02:00.0 VGA compatible controller: Advanced Micro Devices, Inc.
[AMD/ATI] Baffin [Polaris11] (rev ff) (prog-if 00 [VGA controller])
Subsystem: Sapphire Technology Limited Baffin [Radeon RX 560]
Flags: bus master, fast devsel, latency 0, IRQ 51
Memory at d0000000 (64-bit, prefetchable) [size=256M]
Memory at e0000000 (64-bit, prefetchable) [size=2M]
I/O ports at 10000 [size=256]
Memory at e0200000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at e0240000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: amdgpu
Kernel modules: amdgpu
dmesg follows in attachment.
Regards,
Luís
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.20.0-rc7-next3g (lpnm@ENIAC10) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #4 SMP Tue Dec 18 11:37:16 WET 2018
[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: PowerInno Armada Duo
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: UEFI not found.
[ 0.000000] cma: Reserved 16 MiB at 0x7f000000
[ 0.000000] On node 0 totalpages: 524288
[ 0.000000] Normal zone: 1728 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 196608 pages, LIFO batch:63
[ 0.000000] HighMem zone: 327680 pages, LIFO batch:63
[ 0.000000] random: get_random_bytes called from start_kernel+0xac/0x4b4 with crng_init=0
[ 0.000000] percpu: Embedded 18 pages/cpu @(ptrval) s41996 r8192 d23540 u73728
[ 0.000000] pcpu-alloc: s41996 r8192 d23540 u73728 alloc=18*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560
[ 0.000000] Kernel command line: root=/dev/sda2 rw rootfstype=ext4 rootwait console=ttyS0,115200n8
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 2044580K/2097152K available (11264K kernel code, 1037K rwdata, 2808K rodata, 1024K init, 333K bss, 36188K reserved, 16384K cma-reserved, 1294336K highmem)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0x(ptrval) - 0x(ptrval) (12256 kB)
.init : 0x(ptrval) - 0x(ptrval) (1024 kB)
.data : 0x(ptrval) - 0x(ptrval) (1038 kB)
.bss : 0x(ptrval) - 0x(ptrval) ( 334 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] ftrace: allocating 37273 entries in 73 pages
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] L2C-310 erratum 769419 enabled
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 D prefetch enabled, offset 1 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
[ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
[ 0.000007] sched_clock: 64 bits at 800MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.000017] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0xb881274fa3, max_idle_ns: 440795210636 ns
[ 0.000031] Switching to timer-based delay loop, resolution 1ns
[ 0.000192] Ignoring duplicate/late registration of read_current_timer delay
[ 0.000199] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.000416] Console: colour dummy device 80x30
[ 0.000438] Calibrating delay loop (skipped), value calculated using timer frequency.. 1600.00 BogoMIPS (lpj=8000000)
[ 0.000446] pid_max: default: 32768 minimum: 301
[ 0.000574] LSM: Security Framework initializing
[ 0.000579] Yama: becoming mindful.
[ 0.000593] AppArmor: AppArmor disabled by boot time parameter
[ 0.000633] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000639] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.001035] CPU: Testing write buffer coherency: ok
[ 0.001172] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.001399] Setting up static identity map for 0x100000 - 0x100060
[ 0.001470] mvebu-soc-id: MVEBU SoC ID=0x6828, Rev=0xA
[ 0.001541] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.001609] rcu: Hierarchical SRCU implementation.
[ 0.002693] EFI services will not be available.
[ 0.002769] smp: Bringing up secondary CPUs ...
[ 0.002961] Booting CPU 1
[ 0.003122] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.003182] smp: Brought up 1 node, 2 CPUs
[ 0.003188] SMP: Total of 2 processors activated (3200.00 BogoMIPS).
[ 0.003191] CPU: All CPU(s) started in SVC mode.
[ 0.003751] devtmpfs: initialized
[ 0.005415] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.005536] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.005544] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.006044] xor: measuring software checksum speed
[ 0.100074] arm4regs : 2482.000 MB/sec
[ 0.200073] 8regs : 1934.400 MB/sec
[ 0.300072] 32regs : 1985.200 MB/sec
[ 0.400073] neon : 1800.800 MB/sec
[ 0.400076] xor: using function: arm4regs (2482.000 MB/sec)
[ 0.400101] pinctrl core: initialized pinctrl subsystem
[ 0.400330] *************************************************************
[ 0.400333] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
[ 0.400336] ** **
[ 0.400338] ** IOMMU DebugFS SUPPORT HAS BEEN ENABLED IN THIS KERNEL **
[ 0.400341] ** **
[ 0.400343] ** This means that this kernel is built to expose internal **
[ 0.400346] ** IOMMU data structures, which may compromise security on **
[ 0.400348] ** your system. **
[ 0.400350] ** **
[ 0.400353] ** If you see this message and you are not debugging the **
[ 0.400355] ** kernel, report this immediately to your vendor! **
[ 0.400358] ** **
[ 0.400360] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
[ 0.400363] *************************************************************
[ 0.400473] DMI not present or invalid.
[ 0.400643] NET: Registered protocol family 16
[ 0.401952] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.402249] audit: initializing netlink subsys (disabled)
[ 0.402334] audit: type=2000 audit(0.400:1): state=initialized audit_enabled=0 res=1
[ 0.402596] cpuidle: using governor ladder
[ 0.402611] cpuidle: using governor menu
[ 0.402698] No ATAGs?
[ 0.402732] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.402738] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.402867] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
[ 0.402874] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
[ 0.402965] Serial: AMBA PL011 UART driver
[ 0.409679] cryptd: max_cpu_qlen set to 1000
[ 0.570222] raid6: int32x1 gen() 258 MB/s
[ 0.740074] raid6: int32x1 xor() 199 MB/s
[ 0.910181] raid6: int32x2 gen() 300 MB/s
[ 1.080077] raid6: int32x2 xor() 271 MB/s
[ 1.250185] raid6: int32x4 gen() 378 MB/s
[ 1.420143] raid6: int32x4 xor() 305 MB/s
[ 1.590113] raid6: int32x8 gen() 405 MB/s
[ 1.760136] raid6: int32x8 xor() 288 MB/s
[ 1.930096] raid6: neonx1 gen() 1198 MB/s
[ 2.100095] raid6: neonx1 xor() 1100 MB/s
[ 2.270119] raid6: neonx2 gen() 1295 MB/s
[ 2.440097] raid6: neonx2 xor() 1339 MB/s
[ 2.610119] raid6: neonx4 gen() 1349 MB/s
[ 2.780092] raid6: neonx4 xor() 1354 MB/s
[ 2.950090] raid6: neonx8 gen() 1040 MB/s
[ 3.120095] raid6: neonx8 xor() 1032 MB/s
[ 3.120099] raid6: using algorithm neonx4 gen() 1349 MB/s
[ 3.120102] raid6: .... xor() 1354 MB/s, rmw enabled
[ 3.120105] raid6: using neon recovery algorithm
[ 3.121308] vgaarb: loaded
[ 3.121506] SCSI subsystem initialized
[ 3.121582] libata version 3.00 loaded.
[ 3.121671] usbcore: registered new interface driver usbfs
[ 3.121692] usbcore: registered new interface driver hub
[ 3.121719] usbcore: registered new device driver usb
[ 3.121846] media: Linux media interface: v0.10
[ 3.121861] videodev: Linux video capture interface: v2.00
[ 3.121891] pps_core: LinuxPPS API ver. 1 registered
[ 3.121894] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@xxxxxxxx>
[ 3.121903] PTP clock support registered
[ 3.122457] clocksource: Switched to clocksource arm_global_timer
[ 3.185790] VFS: Disk quotas dquot_6.6.0
[ 3.185830] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.189994] NET: Registered protocol family 2
[ 3.190300] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 3.190317] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 3.190355] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 3.190418] TCP: Hash tables configured (established 8192 bind 8192)
[ 3.190472] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 3.190499] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 3.190654] NET: Registered protocol family 1
[ 3.190669] PCI: CLS 0 bytes, default 64
[ 3.191023] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[ 3.195279] Initialise system trusted keyrings
[ 3.195355] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[ 3.198126] zbud: loaded
[ 3.198989] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 3.199211] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[ 4.990493] Key type asymmetric registered
[ 4.990501] Asymmetric key parser 'x509' registered
[ 4.990535] bounce: pool size: 64 pages
[ 4.990565] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 4.990639] io scheduler noop registered
[ 4.990643] io scheduler deadline registered
[ 4.990740] io scheduler cfq registered (default)
[ 4.990745] io scheduler mq-deadline registered
[ 4.990748] io scheduler kyber registered
[ 4.991759] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
[ 4.993297] mv_xor f1060800.xor: Marvell shared XOR driver
[ 5.052997] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 5.053114] mv_xor f1060900.xor: Marvell shared XOR driver
[ 5.112997] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 5.113289] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 5.113978] printk: console [ttyS0] disabled
[ 5.134056] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 22, base_baud = 15625000) is a 16550A
[ 6.112795] printk: console [ttyS0] enabled
[ 6.117311] Serial: AMBA driver
[ 6.121185] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 6.130272] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 6.139623] scsi host0: ahci-mvebu
[ 6.143301] scsi host1: ahci-mvebu
[ 6.146804] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 41
[ 6.154753] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 41
[ 6.162843] ahci-mvebu f10e0000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 6.171913] ahci-mvebu f10e0000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 6.181290] scsi host2: ahci-mvebu
[ 6.184886] scsi host3: ahci-mvebu
[ 6.188382] ata3: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x100 irq 42
[ 6.196328] ata4: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x180 irq 42
[ 6.204746] libphy: Fixed MDIO Bus: probed
[ 6.209166] libphy: orion_mdio_bus: probed
[ 6.213897] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled
[ 6.222920] mvneta f1070000.ethernet eth0: Using device tree mac address 00:50:43:00:01:01
[ 6.231330] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.237910] ehci-pci: EHCI PCI platform driver
[ 6.242389] ehci-orion: EHCI orion driver
[ 6.246502] orion-ehci f1058000.usb: EHCI Host Controller
[ 6.251923] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[ 6.259614] orion-ehci f1058000.usb: irq 37, io mem 0xf1058000
[ 6.292465] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[ 6.298504] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.20
[ 6.306799] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.314042] usb usb1: Product: EHCI Host Controller
[ 6.318930] usb usb1: Manufacturer: Linux 4.20.0-rc7-next3g ehci_hcd
[ 6.326782] usb usb1: SerialNumber: f1058000.usb
[ 6.331667] hub 1-0:1.0: USB hub found
[ 6.335452] hub 1-0:1.0: 1 port detected
[ 6.339801] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 6.345147] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[ 6.352791] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
[ 6.362054] xhci-hcd f10f0000.usb3: irq 43, io mem 0xf10f0000
[ 6.367990] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.20
[ 6.376285] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.383529] usb usb2: Product: xHCI Host Controller
[ 6.388418] usb usb2: Manufacturer: Linux 4.20.0-rc7-next3g xhci-hcd
[ 6.396271] usb usb2: SerialNumber: f10f0000.usb3
[ 6.401213] hub 2-0:1.0: USB hub found
[ 6.404995] hub 2-0:1.0: 1 port detected
[ 6.409083] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 6.414419] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
[ 6.421929] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed
[ 6.428441] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 6.436626] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.20
[ 6.444925] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.452163] usb usb3: Product: xHCI Host Controller
[ 6.457056] usb usb3: Manufacturer: Linux 4.20.0-rc7-next3g xhci-hcd
[ 6.464908] usb usb3: SerialNumber: f10f0000.usb3
[ 6.469873] hub 3-0:1.0: USB hub found
[ 6.473650] hub 3-0:1.0: 1 port detected
[ 6.477818] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 6.483159] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[ 6.490797] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
[ 6.493680] ata2: SATA link down (SStatus 0 SControl 300)
[ 6.500063] xhci-hcd f10f8000.usb3: irq 44, io mem 0xf10f8000
[ 6.511364] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.20
[ 6.519661] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.526905] usb usb4: Product: xHCI Host Controller
[ 6.531792] usb usb4: Manufacturer: Linux 4.20.0-rc7-next3g xhci-hcd
[ 6.535852] ata3: SATA link down (SStatus 0 SControl 300)
[ 6.539643] usb usb4: SerialNumber: f10f8000.usb3
[ 6.545076] ata4: SATA link down (SStatus 0 SControl 300)
[ 6.555335] hub 4-0:1.0: USB hub found
[ 6.559111] hub 4-0:1.0: 1 port detected
[ 6.563205] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 6.568534] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[ 6.576099] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed
[ 6.582616] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[ 6.590850] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.20
[ 6.599144] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.606389] usb usb5: Product: xHCI Host Controller
[ 6.611277] usb usb5: Manufacturer: Linux 4.20.0-rc7-next3g xhci-hcd
[ 6.619129] usb usb5: SerialNumber: f10f8000.usb3
[ 6.624067] hub 5-0:1.0: USB hub found
[ 6.627837] hub 5-0:1.0: 1 port detected
[ 6.632002] usbcore: registered new interface driver uas
[ 6.637415] usbcore: registered new interface driver usb-storage
[ 6.643567] mousedev: PS/2 mouse device common for all mice
[ 6.649648] armada38x-rtc f10a3800.rtc: registered as rtc0
[ 6.655880] pca953x 0-0020: 0-0020 supply vcc not found, using dummy regulator
[ 6.663157] pca953x 0-0020: Linked as a consumer to regulator.0
[ 6.669691] GPIO line 501 (usb3-current-limit) hogged as input
[ 6.672471] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 6.675877] GPIO line 502 (usb3-power) hogged as output/high
[ 6.687450] ata1.00: supports DRM functions and may not be fully accessible
[ 6.687616] GPIO line 511 (usb-current-limit) hogged as input
[ 6.694441] ata1.00: ATA-9: Samsung SSD 850 EVO 120GB, EMT01B6Q, max UDMA/133
[ 6.700480] GPIO line 510 (usb-power) hogged as output/high
[ 6.707350] ata1.00: 234441648 sectors, multi 1: LBA48 NCQ (depth 32)
[ 6.720497] ata1.00: supports DRM functions and may not be fully accessible
[ 6.722473] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 6.734294] orion_wdt: Initial timeout 171 sec
[ 6.739016] sdhci: Secure Digital Host Controller Interface driver
[ 6.745230] sdhci: Copyright(c) Pierre Ossman
[ 6.745240] ata1.00: configured for UDMA/133
[ 6.749732] sdhci-pltfm: SDHCI platform and OF driver helper
[ 6.759818] scsi 0:0:0:0: Direct-Access ATA Samsung SSD 850 1B6Q PQ: 0 ANSI: 5
[ 6.768038] ledtrig-cpu: registered to indicate activity on CPUs
[ 6.768413] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/112 GiB)
[ 6.781613] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 6.781662] sd 0:0:0:0: [sda] Write Protect is off
[ 6.791752] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 6.791932] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.801284] random: fast init done
[ 6.804746] sda: sda1 sda2 sda3
[ 6.808816] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 6.824735] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 6.832623] NET: Registered protocol family 10
[ 6.837598] Segment Routing with IPv6
[ 6.841299] mip6: Mobile IPv6
[ 6.844307] NET: Registered protocol family 17
[ 6.848764] mpls_gso: MPLS GSO support
[ 6.852600] ThumbEE CPU extension supported.
[ 6.856881] Registering SWP/SWPB emulation handler
[ 6.865587] registered taskstats version 1
[ 6.869696] Loading compiled-in X.509 certificates
[ 6.874578] zswap: loaded using pool lzo/zbud
[ 6.879592] Btrfs loaded, crc32c=crc32c-generic
[ 6.884879] Key type encrypted registered
[ 6.888909] ima: No TPM chip found, activating TPM-bypass!
[ 6.894451] ima: Allocated hash algorithm: sha256
[ 6.900235] mvebu-pcie soc:pcie: /soc/pcie/pcie@1,0: reset gpio is active low
[ 6.907766] mvebu-pcie soc:pcie: /soc/pcie/pcie@2,0: reset gpio is active low
[ 6.932470] usb 4-1: new full-speed USB device number 2 using xhci-hcd
[ 6.956978] usb 1-1: New USB device found, idVendor=0bda, idProduct=5411, bcdDevice= 1.17
[ 6.965188] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6.972346] usb 1-1: Product: 4-Port USB 2.0 Hub
[ 6.976983] usb 1-1: Manufacturer: Generic
[ 6.982168] hub 1-1:1.0: USB hub found
[ 6.986977] hub 1-1:1.0: 4 ports detected
[ 7.113021] usb 4-1: New USB device found, idVendor=0d8c, idProduct=000c, bcdDevice= 1.00
[ 7.121228] usb 4-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 7.128389] usb 4-1: Product: C-Media USB Headphone Set
[ 7.152563] mvebu-pcie soc:pcie: PCI host bridge to bus 0000:00
[ 7.158500] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 7.164010] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xefffffff]
[ 7.170901] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 7.177249] pci 0000:00:01.0: [11ab:6828] type 01 class 0x060400
[ 7.177401] pci 0000:00:02.0: [11ab:6828] type 01 class 0x060400
[ 7.178034] PCI: bus0: Fast back to back transfers disabled
[ 7.183633] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 7.191657] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 7.199749] pci 0000:01:00.0: [1ade:3038] type 00 class 0x040000
[ 7.199771] pci 0000:01:00.0: reg 0x10: [mem 0x40000000-0x40000fff]
[ 7.199950] pci 0000:00:01.0: ASPM: current common clock configuration is broken, reconfiguring
[ 7.263041] PCI: bus1: Fast back to back transfers enabled
[ 7.268544] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 7.268623] pci 0000:02:00.0: [1002:67ff] type 00 class 0x030000
[ 7.268673] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x0fffffff 64bit pref]
[ 7.268686] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x001fffff 64bit pref]
[ 7.268695] pci 0000:02:00.0: reg 0x20: [io 0x0000-0x00ff]
[ 7.268704] pci 0000:02:00.0: reg 0x24: [mem 0x00000000-0x0003ffff]
[ 7.268713] pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
[ 7.268725] pci 0000:02:00.0: enabling Extended Tags
[ 7.273835] pci 0000:02:00.0: supports D1 D2
[ 7.273839] pci 0000:02:00.0: PME# supported from D1 D2 D3hot D3cold
[ 7.273891] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:02.0 (capable of 63.008 Gb/s with 8 GT/s x8 link)
[ 7.287922] pci 0000:02:00.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none
[ 7.296333] pci 0000:02:00.1: [1002:aae0] type 00 class 0x040300
[ 7.296369] pci 0000:02:00.1: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
[ 7.296409] pci 0000:02:00.1: enabling Extended Tags
[ 7.301467] pci 0000:02:00.1: supports D1 D2
[ 7.301619] pci 0000:00:02.0: ASPM: current common clock configuration is broken, reconfiguring
[ 7.312467] usb 1-1.1: new low-speed USB device number 3 using orion-ehci
[ 7.333073] PCI: bus2: Fast back to back transfers disabled
[ 7.338666] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 7.338694] pci 0000:00:02.0: BAR 8: assigned [mem 0xd0000000-0xe7ffffff]
[ 7.345514] pci 0000:00:01.0: BAR 8: assigned [mem 0xe8000000-0xe80fffff]
[ 7.352321] pci 0000:00:02.0: BAR 7: assigned [io 0x10000-0x10fff]
[ 7.358625] pci 0000:01:00.0: BAR 0: assigned [mem 0xe8000000-0xe8000fff]
[ 7.365448] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 7.370425] pci 0000:00:01.0: bridge window [mem 0xe8000000-0xe80fffff]
[ 7.377257] pci 0000:02:00.0: BAR 0: assigned [mem 0xd0000000-0xdfffffff 64bit pref]
[ 7.385041] pci 0000:02:00.0: BAR 2: assigned [mem 0xe0000000-0xe01fffff 64bit pref]
[ 7.392820] pci 0000:02:00.0: BAR 5: assigned [mem 0xe0200000-0xe023ffff]
[ 7.399625] pci 0000:02:00.0: BAR 6: assigned [mem 0xe0240000-0xe025ffff pref]
[ 7.406872] pci 0000:02:00.1: BAR 0: assigned [mem 0xe0260000-0xe0263fff 64bit]
[ 7.414211] pci 0000:02:00.0: BAR 4: assigned [io 0x10000-0x100ff]
[ 7.420497] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 7.425479] pci 0000:00:02.0: bridge window [io 0x10000-0x10fff]
[ 7.431761] pci 0000:00:02.0: bridge window [mem 0xd0000000-0xe7ffffff]
[ 7.438625] pcieport 0000:00:01.0: enabling device (0140 -> 0142)
[ 7.444797] pcieport 0000:00:02.0: enabling device (0140 -> 0143)
[ 7.450995] pci 0000:02:00.1: Linked as a consumer to 0000:02:00.0
[ 7.457412] sr_init: No PMIC hook to init smartreflex
[ 7.478531] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 7.486240] VFS: Mounted root (ext4 filesystem) on device 8:2.
[ 7.494491] Freeing unused kernel memory: 1024K
[ 7.502667] Run /sbin/init as init process
[ 7.559491] usb 1-1.1: New USB device found, idVendor=145f, idProduct=01d3, bcdDevice= 3.11
[ 7.567890] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 7.575238] usb 1-1.1: Product: Trust Wireless TouchKB
[ 7.580397] usb 1-1.1: Manufacturer: Trust
[ 7.595538] systemd[1]: System time before build time, advancing clock.
[ 7.627572] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 7.649217] systemd[1]: Detected architecture arm.
[ 7.682480] usb 1-1.2: new high-speed USB device number 4 using orion-ehci
[ 7.692750] systemd[1]: Set hostname to <picolo>.
[ 7.770208] systemd-fstab-generator[214]: Checking was requested for "/", but it is not a device.
[ 7.834107] usb 1-1.2: New USB device found, idVendor=0bda, idProduct=8179, bcdDevice= 0.00
[ 7.842556] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7.849896] usb 1-1.2: Product: 802.11n NIC
[ 7.854096] usb 1-1.2: Manufacturer: Realtek
[ 7.858378] usb 1-1.2: SerialNumber: 00E04C0001
[ 7.941810] random: systemd: uninitialized urandom read (16 bytes read)
[ 7.949067] systemd[1]: Created slice System Slice.
[ 7.972481] usb 1-1.3: new high-speed USB device number 5 using orion-ehci
[ 7.982790] random: systemd: uninitialized urandom read (16 bytes read)
[ 7.989531] systemd[1]: Listening on Journal Audit Socket.
[ 8.022537] random: systemd: uninitialized urandom read (16 bytes read)
[ 8.029599] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 8.062770] systemd[1]: Listening on Journal Socket.
[ 8.093447] systemd[1]: Detaching egress BPF program from cgroup failed: Invalid argument
[ 8.102716] systemd[1]: Mounting Kernel Debug File System...
[ 8.123732] usb 1-1.3: New USB device found, idVendor=0781, idProduct=5595, bcdDevice= 1.00
[ 8.132111] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 8.139457] usb 1-1.3: Product: Ultra USB 3.0
[ 8.143837] usb 1-1.3: Manufacturer: SanDisk
[ 8.148120] usb 1-1.3: SerialNumber: 4C531001590825112463
[ 8.149152] systemd[1]: Detaching egress BPF program from cgroup failed: Invalid argument
[ 8.162218] usb-storage 1-1.3:1.0: USB Mass Storage device detected
[ 8.172704] scsi host4: usb-storage 1-1.3:1.0
[ 8.691340] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[ 9.193793] scsi 4:0:0:0: Direct-Access SanDisk Ultra USB 3.0 1.00 PQ: 0 ANSI: 6
[ 9.194355] sd 4:0:0:0: Attached scsi generic sg1 type 0
[ 9.194875] sd 4:0:0:0: [sdb] 121307136 512-byte logical blocks: (62.1 GB/57.8 GiB)
[ 9.196247] sd 4:0:0:0: [sdb] Write Protect is off
[ 9.196251] sd 4:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 9.196869] sd 4:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 9.205792] sdb: sdb1 sdb2 sdb3
[ 9.208528] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 9.495201] systemd-journald[243]: Received request to flush runtime journal from PID 1
[ 9.500732] systemd-journald[243]: File /var/log/journal/b031e9b6d79d46d78bcd2ae487848e34/system.journal corrupted or uncleanly shut down, renaming and replacing.
[ 9.875137] SMI PCIe driver 0000:01:00.0: enabling device (0000 -> 0002)
[ 9.875148] SMI PCIe driver 0000:01:00.0: card detected: DVBSky T9580 V3
[ 9.891866] hidraw: raw HID events driver (C) Jiri Kosina
[ 9.950668] usbcore: registered new interface driver usbhid
[ 9.950672] usbhid: USB HID core driver
[ 9.981417] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 10.022866] dvbdev: DVB: registering new adapter (SMI_DVB)
[ 10.150903] i2c i2c-1: Added multiplexed i2c bus 3
[ 10.150910] si2168 1-0064: Silicon Labs Si2168-B40 successfully identified
[ 10.150914] si2168 1-0064: firmware version: B 4.0.2
[ 10.167673] si2157 3-0060: Silicon Labs Si2147/2148/2157/2158 successfully attached
[ 10.210296] SMI PCIe driver 0000:01:00.0: DVB: registering adapter 0 frontend 0 (Silicon Labs Si2168)...
[ 10.220712] SMI PCIe driver 0000:01:00.0: DVBSky T9580 V3 port 0 MAC: 00:18:33:34:85:51
[ 10.233830] dvbdev: DVB: registering new adapter (SMI_DVB)
[ 10.269512] i2c i2c-2: Added multiplexed i2c bus 4
[ 10.474406] snd_hda_intel 0000:02:00.1: enabling device (0140 -> 0142)
[ 10.474417] snd_hda_intel 0000:02:00.1: Force to snoop mode by module option
[ 10.510668] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/platform/soc/soc:pcie/pci0000:00/0000:00:02.0/0000:02:00.1/sound/card0/input0
[ 10.510752] input: HDA ATI HDMI HDMI/DP,pcm=7 as /devices/platform/soc/soc:pcie/pci0000:00/0000:00:02.0/0000:02:00.1/sound/card0/input1
[ 10.510820] input: HDA ATI HDMI HDMI/DP,pcm=8 as /devices/platform/soc/soc:pcie/pci0000:00/0000:00:02.0/0000:02:00.1/sound/card0/input2
[ 10.510886] input: HDA ATI HDMI HDMI/DP,pcm=9 as /devices/platform/soc/soc:pcie/pci0000:00/0000:00:02.0/0000:02:00.1/sound/card0/input3
[ 10.510954] input: HDA ATI HDMI HDMI/DP,pcm=10 as /devices/platform/soc/soc:pcie/pci0000:00/0000:00:02.0/0000:02:00.1/sound/card0/input4
[ 10.517062] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 10.523031] ts2020 4-0060: Montage Technology TS2022 successfully identified
[ 10.535158] lib80211: common routines for IEEE802.11 drivers
[ 10.535162] lib80211_crypt: registered algorithm 'NULL'
[ 10.536154] usbcore: registered new interface driver snd-usb-audio
[ 10.543958] r8188eu: module is from the staging directory, the quality is unknown, you have been warned.
[ 10.552803] SMI PCIe driver 0000:01:00.0: DVB: registering adapter 1 frontend 0 (Montage Technology M88DS3103)...
[ 10.559125] SMI PCIe driver 0000:01:00.0: DVBSky T9580 V3 port 1 MAC: 00:18:33:54:85:52
[ 10.579104] Chip Version Info: CHIP_8188E_Normal_Chip_TSMC_D_CUT_1T1R_RomVer(0)
[ 10.610237] Adding 7905276k swap on /dev/sda3. Priority:-2 extents:1 across:7905276k SSFS
[ 10.648178] input: C-Media USB Headphone Set as /devices/platform/soc/soc:internal-regs/f10f8000.usb3/usb4/4-1/4-1:1.3/0003:0D8C:000C.0001/input/input6
[ 10.653144] Registered IR keymap rc-dvbsky
[ 10.653224] rc rc0: IR (DVBSky T9580 V3) as /devices/platform/soc/soc:pcie/pci0000:00/0000:00:01.0/0000:01:00.0/rc/rc0
[ 10.653426] input: IR (DVBSky T9580 V3) as /devices/platform/soc/soc:pcie/pci0000:00/0000:00:01.0/0000:01:00.0/rc/rc0/input5
[ 10.688484] usbcore: registered new interface driver r8188eu
[ 10.712833] hid-generic 0003:0D8C:000C.0001: input,hidraw0: USB HID v1.00 Device [C-Media USB Headphone Set ] on usb-f10f8000.usb3-1/input3
[ 10.713332] input: Trust Trust Wireless TouchKB as /devices/platform/soc/soc:internal-regs/f1058000.usb/usb1/1-1/1-1.1/1-1.1:1.0/0003:145F:01D3.0002/input/input7
[ 10.782960] hid-generic 0003:145F:01D3.0002: input,hidraw1: USB HID v1.10 Keyboard [Trust Trust Wireless TouchKB] on usb-f1058000.usb-1.1/input0
[ 10.783948] input: Trust Trust Wireless TouchKB Mouse as /devices/platform/soc/soc:internal-regs/f1058000.usb/usb1/1-1/1-1.1/1-1.1:1.1/0003:145F:01D3.0003/input/input8
[ 10.784234] input: Trust Trust Wireless TouchKB System Control as /devices/platform/soc/soc:internal-regs/f1058000.usb/usb1/1-1/1-1.1/1-1.1:1.1/0003:145F:01D3.0003/input/input9
[ 10.836282] [drm] amdgpu kernel modesetting enabled.
[ 10.836427] amdgpu 0000:02:00.0: enabling device (0140 -> 0143)
[ 10.836973] [drm] initializing kernel modesetting (POLARIS11 0x1002:0x67FF 0x1DA2:0xE367 0xFF).
[ 10.836986] [drm] register mmio base: 0xE0200000
[ 10.836988] [drm] register mmio size: 262144
[ 10.837029] [drm] add ip block number 0 <vi_common>
[ 10.837032] [drm] add ip block number 1 <gmc_v8_0>
[ 10.837034] [drm] add ip block number 2 <tonga_ih>
[ 10.837035] [drm] add ip block number 3 <gfx_v8_0>
[ 10.837037] [drm] add ip block number 4 <sdma_v3_0>
[ 10.837039] [drm] add ip block number 5 <powerplay>
[ 10.837042] [drm] add ip block number 6 <dm>
[ 10.837044] [drm] add ip block number 7 <uvd_v6_0>
[ 10.837045] [drm] add ip block number 8 <vce_v3_0>
[ 10.837063] [drm] UVD is enabled in VM mode
[ 10.837065] [drm] UVD ENC is enabled in VM mode
[ 10.837069] [drm] VCE enabled in VM mode
[ 10.963255] input: Trust Trust Wireless TouchKB Consumer Control as /devices/platform/soc/soc:internal-regs/f1058000.usb/usb1/1-1/1-1.1/1-1.1:1.1/0003:145F:01D3.0003/input/input10
[ 10.963335] input: Trust Trust Wireless TouchKB as /devices/platform/soc/soc:internal-regs/f1058000.usb/usb1/1-1/1-1.1/1-1.1:1.1/0003:145F:01D3.0003/input/input11
[ 10.972525] hid-generic 0003:145F:01D3.0003: input,hiddev0,hidraw2: USB HID v1.10 Mouse [Trust Trust Wireless TouchKB] on usb-f1058000.usb-1.1/input1
[ 11.056045] ATOM BIOS: 113-367BF-U41
[ 11.056076] [drm] GPU posting now...
[ 11.206140] [drm] vm size is 64 GB, 2 levels, block size is 10-bit, fragment size is 9-bit
[ 11.207212] amdgpu 0000:02:00.0: VRAM: 4096M 0x000000F400000000 - 0x000000F4FFFFFFFF (4096M used)
[ 11.207218] amdgpu 0000:02:00.0: GART: 256M 0x000000FF00000000 - 0x000000FF0FFFFFFF
[ 11.207224] [drm] Detected VRAM RAM=4096M, BAR=256M
[ 11.207227] [drm] RAM width 128bits GDDR5
[ 11.207689] [TTM] Zone kernel: Available graphics memory: 375634 kiB
[ 11.207693] [TTM] Zone highmem: Available graphics memory: 1030994 kiB
[ 11.207695] [TTM] Initializing pool allocator
[ 11.207717] [drm] amdgpu: 4096M of VRAM memory ready
[ 11.207721] [drm] amdgpu: 1510M of GTT memory ready.
[ 11.207787] [drm] GART: num cpu pages 65536, num gpu pages 65536
[ 11.208529] [drm] PCIE GART of 256M enabled (table at 0x000000F400000000).
[ 11.230285] [drm] Chained IB support enabled!
[ 11.280098] r8188eu 1-1.2:1.0 wlx7c8bca0fc623: renamed from wlan0
[ 11.384846] [drm] Found UVD firmware Version: 1.130 Family ID: 16
[ 12.243671] [drm] Found VCE firmware Version: 52.4 Binary ID: 3
[ 12.414150] [drm] DM_PPLIB: values for Engine clock
[ 12.414155] [drm] DM_PPLIB: 214000
[ 12.414157] [drm] DM_PPLIB: 335000
[ 12.414159] [drm] DM_PPLIB: 503000
[ 12.414160] [drm] DM_PPLIB: 697000
[ 12.414161] [drm] DM_PPLIB: 874000
[ 12.414163] [drm] DM_PPLIB: 1019000
[ 12.414164] [drm] DM_PPLIB: 1043000
[ 12.414165] [drm] DM_PPLIB: 1071000
[ 12.414168] [drm] DM_PPLIB: Validation clocks:
[ 12.414170] [drm] DM_PPLIB: engine_max_clock: 107100
[ 12.414172] [drm] DM_PPLIB: memory_max_clock: 150000
[ 12.414173] [drm] DM_PPLIB: level : 8
[ 12.414178] [drm] DM_PPLIB: values for Memory clock
[ 12.414180] [drm] DM_PPLIB: 300000
[ 12.414181] [drm] DM_PPLIB: 625000
[ 12.414182] [drm] DM_PPLIB: 1500000
[ 12.414184] [drm] DM_PPLIB: Validation clocks:
[ 12.414185] [drm] DM_PPLIB: engine_max_clock: 107100
[ 12.414187] [drm] DM_PPLIB: memory_max_clock: 150000
[ 12.414188] [drm] DM_PPLIB: level : 8
[ 12.417380] [drm] Display Core initialized with v3.1.68!
[ 12.793616] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 12.793620] [drm] Driver supports precise vblank timestamp query.
[ 12.822124] [drm] UVD and UVD ENC initialized successfully.
[ 12.875116] random: crng init done
[ 12.875121] random: 7 urandom warning(s) missed due to ratelimiting
[ 12.931733] [drm] VCE initialized successfully.
[ 12.935451] [drm] fb mappable at 0xD0528000
[ 12.935455] [drm] vram apper at 0xD0000000
[ 12.935457] [drm] size 1228800
[ 12.935459] [drm] fb depth is 24
[ 12.935460] [drm] pitch is 2560
[ 12.961634] Console: switching to colour frame buffer device 80x30
[ 12.989607] amdgpu 0000:02:00.0: fb0: amdgpudrmfb frame buffer device
[ 13.024465] [drm] Initialized amdgpu 3.27.0 20150101 for 0000:02:00.0 on minor 0
[ 13.504565] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.509245] mvneta f1070000.ethernet eth0: PHY [f1072004.mdio-mii:00] driver [Marvell 88E1510]
[ 13.509680] mvneta f1070000.ethernet eth0: configuring for phy/rgmii-id link mode
[ 13.510155] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.532260] IPv6: ADDRCONF(NETDEV_UP): wlx7c8bca0fc623: link is not ready
[ 14.307027] IPv6: ADDRCONF(NETDEV_UP): wlx7c8bca0fc623: link is not ready
[ 14.490356] IPv6: ADDRCONF(NETDEV_UP): wlx7c8bca0fc623: link is not ready
[ 24.801861] [drm:amdgpu_job_timedout [amdgpu]] *ERROR* ring gfx timeout, signaled seq=2, emitted seq=3
[ 24.811203] [drm] GPU recovery disabled.
[ 25.987116] R8188EU: assoc success
[ 26.012439] IPv6: ADDRCONF(NETDEV_CHANGE): wlx7c8bca0fc623: link becomes ready
_______________________________________________
amd-gfx mailing list
amd-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/amd-gfx
