On 07-05-19, 08:54, Pierre-Louis Bossart wrote:
> On 5/7/19 12:19 AM, Vinod Koul wrote:
> > On 06-05-19, 11:46, Pierre-Louis Bossart wrote:
> > > On 5/6/19 11:22 AM, Vinod Koul wrote:
> > > > On 06-05-19, 17:19, Greg KH wrote:
> > > > > On Mon, May 06, 2019 at 09:42:35AM -0500, Pierre-Louis Bossart wrote:
> > > > > > > > +
> > > > > > > > +int sdw_sysfs_slave_init(struct sdw_slave *slave)
> > > > > > > > +{
> > > > > > > > + struct sdw_slave_sysfs *sysfs;
> > > > > > > > + unsigned int src_dpns, sink_dpns, i, j;
> > > > > > > > + int err;
> > > > > > > > +
> > > > > > > > + if (slave->sysfs) {
> > > > > > > > + dev_err(&slave->dev, "SDW Slave sysfs is already initialized\n");
> > > > > > > > + err = -EIO;
> > > > > > > > + goto err_ret;
> > > > > > > > + }
> > > > > > > > +
> > > > > > > > + sysfs = kzalloc(sizeof(*sysfs), GFP_KERNEL);
> > > > > > >
> > > > > > > Same question as patch 1, why a new device?
> > > > > >
> > > > > > yes it's the same open. In this case, the slave devices are defined at a
> > > > > > different level so it's also confusing to create a device to represent the
> > > > > > slave properties. The code works but I am not sure the initial directions
> > > > > > are correct.
> > > > >
> > > > > You can just make a subdir for your attributes by using the attribute
> > > > > group name, if a subdirectory is needed just to keep things a bit more
> > > > > organized.
> > > >
> > > > The key here is 'a subdir' which is not the case here. We did discuss
> > > > this in the initial patches for SoundWire which had sysfs :)
> > > >
> > > > The way MIPI disco spec organized properties, we have dp0 and dpN
> > > > properties each of them requires to have a subdir of their own and that
> > > > was the reason why I coded it to be creating a device.
> > >
> > > Vinod, the question was not for dp0 and dpN, it's fine to have
> > > subdirectories there, but rather why we need separate devices for the master
> > > and slave properties.
> >
> > Slave does not have a separate device. IIRC the properties for Slave are
> > in /sys/bus/soundwire/device/<slave>/...
>
> I am not sure this is correct
>
> ACPI defines the slaves devices under
> /sys/bus/acpi/PRP0001, e.g.
Yes the bus will create 'soundwire slave' device type (In acpi case
created from ACPI walk) and we do link the ACPI as the firmware node.
This is 'not' created for properties but for soundwire representation of
slave devices. This is the one code driver attaches to.
> /sys/bus/acpi/devices/PRP00001:00/device:17# ls
Yes this would the companion ACPI device
> adr mipi-sdw-dp-5-sink-subproperties
> intel-endpoint-descriptor-0 mipi-sdw-dp-6-source-subproperties
> intel-endpoint-descriptor-1 mipi-sdw-dp-7-sink-subproperties
> mipi-sdw-dp-0-subproperties mipi-sdw-dp-8-source-subproperties
> mipi-sdw-dp-1-sink-subproperties path
> mipi-sdw-dp-1-source-subproperties physical_node
> mipi-sdw-dp-2-sink-subproperties power
> mipi-sdw-dp-2-source-subproperties subsystem
> mipi-sdw-dp-3-sink-subproperties uevent
> mipi-sdw-dp-4-source-subproperties
>
> but the sysfs for slaves is shown as
> /sys/bus/acpi/devices/PRP00001:00/int-sdw.0/sdw:0:25d:700:0:0# ls
> bank_delay_support master_count sink_ports
> ch_prep_timeout mipi_revision source_ports
> clk_stop_mode1 modalias src-dp2
> clk_stop_timeout p15_behave src-dp4
> dp0 paging_support subsystem
> driver power test_mode_capable
> firmware_node reset_behave uevent
> hda_reg simple_clk_stop_capable wake_capable
> high_PHY_capable sink-dp1
> index_reg sink-dp3
>
> and in sys/bus/soundwire/devices/sdw:0:25d:700:0:0# ls
I think both are same nodes. Since the SoundWire slave is a child of
master it appears under int-sdw.0 as well
> bank_delay_support master_count sink_ports
> ch_prep_timeout mipi_revision source_ports
> clk_stop_mode1 modalias src-dp2
> clk_stop_timeout p15_behave src-dp4
> dp0 paging_support subsystem
> driver power test_mode_capable
> firmware_node reset_behave uevent
> hda_reg simple_clk_stop_capable wake_capable
> high_PHY_capable sink-dp1
> index_reg sink-dp3
>
> So I would think we *do* create a new device for each slave instead of using
> the one that's already exposed by ACPI.
>
> >
> > For master yes we can skip the device creation, it was done for
> > consistency sake of having these properties ties into sys/bus/soundwire/
> >
> > I don't mind if they are shown up in respective device node (PCI/platform
> > etc) /sys/bus/foo/device/<>
> >
> > But for creating subdirectories you would need the new dpX devices.
>
> yes, that's agreed.
--
~Vinod
_______________________________________________
Alsa-devel mailing list
Alsa-devel@xxxxxxxxxxxxxxxx
https://mailman.alsa-project.org/mailman/listinfo/alsa-devel
