From: Philipp Zabel <p.zabel@xxxxxxxxxxxxxx> According to the ssm2603 data sheet (control register sequencing), the digital core should be activated only after all necessary bits in the power register are enabled, and a delay determined by the decoupling capacitor on the VMID pin has passed. If the digital core is activated too early, or even before the ADC is powered up, audible artifacts appear at the beginning of the recorded signal. The digital core is also needed for playback, so when recording starts it may already be enabled. This means we cannot get the power sequence correct when we want to be able to start recording after playback. As a workaround put the MIC mute switch into the DAPM routes. This way we can keep the recording disabled until the MIC Bias has settled and thus get rid of audible artifacts. Signed-off-by: Philipp Zabel <p.zabel@xxxxxxxxxxxxxx> m.felsch@xxxxxxxxxxxxxx: adapt commit message m.felsch@xxxxxxxxxxxxxx: drop of configuration as mentioned by Mark: https://patchwork.kernel.org/patch/10407449/ Signed-off-by: Marco Felsch <m.felsch@xxxxxxxxxxxxxx> --- Changelog: v2: - drop OF timeout configuration - adapt commit message sound/soc/codecs/ssm2602.c | 30 ++++++++++++++++++++++++++++-- 1 file changed, 28 insertions(+), 2 deletions(-) diff --git a/sound/soc/codecs/ssm2602.c b/sound/soc/codecs/ssm2602.c index 580ab8916854..fa042b340c6d 100644 --- a/sound/soc/codecs/ssm2602.c +++ b/sound/soc/codecs/ssm2602.c @@ -12,6 +12,7 @@ * Bugs: Enter bugs at http://blackfin.uclinux.org/ */ +#include <linux/delay.h> #include <linux/module.h> #include <linux/regmap.h> #include <linux/slab.h> @@ -97,7 +98,6 @@ SOC_SINGLE_TLV("Sidetone Playback Volume", SSM2602_APANA, 6, 3, 1, SOC_SINGLE("Mic Boost (+20dB)", SSM2602_APANA, 0, 1, 0), SOC_SINGLE("Mic Boost2 (+20dB)", SSM2602_APANA, 8, 1, 0), -SOC_SINGLE("Mic Switch", SSM2602_APANA, 1, 1, 1), }; /* Output Mixer */ @@ -107,10 +107,31 @@ SOC_DAPM_SINGLE("HiFi Playback Switch", SSM2602_APANA, 4, 1, 0), SOC_DAPM_SINGLE("Mic Sidetone Switch", SSM2602_APANA, 5, 1, 0), }; +static const struct snd_kcontrol_new mic_ctl = + SOC_DAPM_SINGLE("Switch", SSM2602_APANA, 1, 1, 1); + /* Input mux */ static const struct snd_kcontrol_new ssm2602_input_mux_controls = SOC_DAPM_ENUM("Input Select", ssm2602_enum[0]); +static int ssm2602_mic_switch_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + /* + * According to the ssm2603 data sheet (control register sequencing), + * the digital core should be activated only after all necessary bits + * in the power register are enabled, and a delay determined by the + * decoupling capacitor on the VMID pin has passed. If the digital core + * is activated too early, or even before the ADC is powered up, audible + * artifacts appear at the beginning and end of the recorded signal. + * + * In practice, audible artifacts disappear well over 500 ms. + */ + msleep(500); + + return 0; +} + static const struct snd_soc_dapm_widget ssm260x_dapm_widgets[] = { SND_SOC_DAPM_DAC("DAC", "HiFi Playback", SSM2602_PWR, 3, 1), SND_SOC_DAPM_ADC("ADC", "HiFi Capture", SSM2602_PWR, 2, 1), @@ -132,6 +153,9 @@ SND_SOC_DAPM_MIXER("Output Mixer", SSM2602_PWR, 4, 1, SND_SOC_DAPM_MUX("Input Mux", SND_SOC_NOPM, 0, 0, &ssm2602_input_mux_controls), SND_SOC_DAPM_MICBIAS("Mic Bias", SSM2602_PWR, 1, 1), +SND_SOC_DAPM_SWITCH_E("Mic Switch", SSM2602_APANA, 1, 1, &mic_ctl, + ssm2602_mic_switch_event, SND_SOC_DAPM_PRE_PMU), + SND_SOC_DAPM_OUTPUT("LHPOUT"), SND_SOC_DAPM_OUTPUT("RHPOUT"), SND_SOC_DAPM_INPUT("MICIN"), @@ -164,9 +188,11 @@ static const struct snd_soc_dapm_route ssm2602_routes[] = { {"LHPOUT", NULL, "Output Mixer"}, {"Input Mux", "Line", "Line Input"}, - {"Input Mux", "Mic", "Mic Bias"}, + {"Input Mux", "Mic", "Mic Switch"}, {"ADC", NULL, "Input Mux"}, + {"Mic Switch", NULL, "Mic Bias"}, + {"Mic Bias", NULL, "MICIN"}, }; -- 2.20.1 _______________________________________________ Alsa-devel mailing list Alsa-devel@xxxxxxxxxxxxxxxx http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
