On Tue, 30 Oct 2018 13:04:33 +0100,
Timo Wischer wrote:
>
> Best regards
> Timo Wischer
> Engineering Software Base (ADITG/ESB)
>
> Tel. +49 5121 49 6938
> On 10/30/18 11:49, Takashi Iwai wrote:
>
> On Tue, 30 Oct 2018 11:39:38 +0100,
> <twischer@xxxxxxxxxxxxxx> wrote:
>
> From: Laxmi Devi <Laxmi.Devi@xxxxxxxxxxxx>
>
> These changes are required due to the kernel commit 07b7acb51d283d8469696c906b91f1882696a4d4
> ("ASoC: rsnd: update pointer more accurate")
>
> Issue is that snd_pcm_wait() goes back to waiting because the hw_ptr
> is not period aligned. Therefore snd_pcm_wait() will block for a longer
> time as required.
>
> With these rcar driver changes the exact position of the dma is returned.
> During snd_pcm_start they read hw_ptr as reference, and this hw_ptr
> is now not period aligned, and is a little ahead over the period while it
> is read. Therefore when the avail is calculated during snd_pcm_wait(),
> it is missing the avail_min by a few frames.
> Consider the below example:
>
> Considering the application is trying to write 0x120 frames and the
> period_size = 0x60, avail_min = 0x120 and buffersize = 0x360 :
>
> rsnd_pointer=0x12c -> dma pointer at the end of second write during
> snd_pcm_dmix_start().
> Since another 0x120 buffer is available, application writes 0x120 and goes
> to snd_pcm_wait().
> It is woken up after 3 snd_pcm_period_elapsed() to see rsnd_pointer=0x248.
> So hw_ptr = new_slave_hw_ptr - reference_slave_hw_ptr = 0x248 - 0x12c = 0x11c.
> It needs 4 more frames to be able to write. And so it goes back to waiting.
>
> But since 3 snd_pcm_period_elapsed(), 3 periods should be available and it
> should have been able to write.
> If rsnd_pointer during the start was 0x120 which is 3 periods
> then 0x248 - 0x120 = 128 it could go on with write.
>
> Signed-off-by: Laxmi Devi <Laxmi.Devi@xxxxxxxxxxxx>
> ---
>
> On 10/29/18 16:54, Takashi Iwai wrote:
> The problem is that aligning the start essentially imposes an
> artificial long latency, and changes the behavior out of sudden.
>
> Now, we are only align the salve_hw_ptr which also solves our delay issue.
> But this change should not increase the latency because the write position
> is given by slave_appl_ptr.
> Do you see any other drawbacks?
>
> How does this work? I thought hwptr is synced to the actual slave
> value soon later in anyway?
>
> The slave_hw_ptr is initialized in reset_slave_ptr() and updated in
> snd_pcm_dmix_sync_ptr() with
>
> dmix->slave_hw_ptr = *dmix->spcm->hw.ptr;
>
> The hw_ptr will be incremented in snd_pcm_dmix_sync_ptr() by adding the diff
> between the last slave_hw_ptr and the current slave_hw_ptr. Due to the
> alignment of the slave_hw_ptr on startup (in reset_slave_ptr()) the offset
> between the slave_hw_ptr and hw_ptr is a multiple of slave_period.
Yes, and is this correct? Suppose you start a stream at the position
one sample before the next period (psize * N + (psize-1)). Then
slave_hw_ptr is psize * N. At the next moment, the dpcm->hw.ptr
reaches to psize * (N+1), and snd_pcm_dmix_sync_ptr() gets called.
Then slave_hw_ptr will be updated to psize * (N+1) although only one
sample has been processed?
> The
> following slave_hw_ptr will be always x * period_size + y where x is always
> incremented for each snd_pcm_period_elapsed() call. y can be sometimes 0 but
> also contain some frames due to the delay between the DMA interrupt till
> reading the current DMA position.
>
> The diff between the salve_hw_ptr will be continuously added to hw_ptr.
> Sometimes the diff can be < period_size but anyway the hw_ptr follows the same
> interval as the salve_hw_ptr:
>
> * 1 * period_size + y1
> * 2 * period_size + y2
> * 3 * period_size + y3
> * ...
>
> y can differ between the snd_pcm_dmix_sync_ptr() calls. But it is never <0.
> Therefore the application can always write one period if it writes all chunks
> in periods.
The update timing is right, but what about the first samples?
thanks,
Takashi
>
> Best regards
>
> Timo
>
> thanks,
>
> Takashi
>
> Best regards
>
> Timo
>
> diff --git a/src/pcm/pcm_dmix.c b/src/pcm/pcm_dmix.c
> index a6a8f3a..eaa0b0f 100644
> --- a/src/pcm/pcm_dmix.c
> +++ b/src/pcm/pcm_dmix.c
> @@ -560,6 +560,8 @@ static int snd_pcm_dmix_hwsync(snd_pcm_t *pcm)
> static void reset_slave_ptr(snd_pcm_t *pcm, snd_pcm_direct_t *dmix)
> {
> dmix->slave_appl_ptr = dmix->slave_hw_ptr = *dmix->spcm->hw.ptr;
> + dmix->slave_hw_ptr = ((dmix->slave_hw_ptr / dmix->slave_period_size)
> + * dmix->slave_period_size);
> if (pcm->buffer_size > pcm->period_size * 2)
> return;
> /* If we have too litte periods, better to align the start position
> --
> 2.7.4
>
>
_______________________________________________
Alsa-devel mailing list
Alsa-devel@xxxxxxxxxxxxxxxx
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
