Dear Mark (cc'ing ALSA-user, ALSA-devel) Thank you for your tutorial http://www.pogo.org.uk/~mark/trx/streaming-desktop-audio.html I found it helpful and clearly-written (although missing a "}" brace and I think it should be "-P" instead of "-p"...). I got as far as trying the 'alsaloop' example. It seems very finicky, sometimes I am able to play a test.wav cleanly through the loopback device, and sometimes there are a lot of crackles and I get errors like playback hw:0: change avail_min=2968 playback hw:0: change avail_min=2972 playback hw:0: change avail_min=2976 underrun for playback hw:0 last write before 9.8370ms, queued 10.0000ms/0.0000ms -> missing -0.1630ms expected 10.0000ms, processing 0.1910ms, max missing 0.0443ms last wake 0.0350ms, last check 0.0350ms, avail_min 32.0000ms max buf 40.0000ms, pfilled 0.0000ms, cfilled 10.0000ms job started before 0.0110ms For 'aplay' invocations where there are errors, it generally never recovers; the whole (10 second) wav file is played with crackles and errors being printed. I tried to figure out if this is due to some different rate settings being chosen at random with each 'aplay' invocation, but all the alsaloop debugging output looks the same between working and non-working runs of aplay (except for the above underrun errors). I also tried various settings for -A and -S in 'alsaloop', but nothing would alleviate this problem. The only thing that fixes it is to change the latency '-t' setting to a higher value than the default 10ms. However this seems like a bad solution, given that it is able (50% of the time) to play a whole sound file at the lower latency with no errors; I would rather have it recover from the underruns when they happen, than increase the latency for every invocation. Enabling realtime via the Arch Wiki info (a bit tricky as I had to edit some of the files by hand) didn't change this behavior. I also encountered a problem when trying to make alsaloop output to a dmix device. I wanted to have it output to dmix so that I could use my audio normally while experimenting with alsaloop. I got a "Poll FD initialization failed." error: playback plug:hw0mix/capture hubcap sync type: CAPTRATESHIFT New pitch for playback plug:hw0mix/capture hubcap: 1.00000000 (min/max samples = 0/0) underrun for playback plug:hw0mix last write before 19.7440ms, queued -1.0000ms/-1.0000ms -> missing -1.0000ms expected 10.0000ms, processing 0.0290ms, max missing 0.0000ms last wake 1539883911239.1819ms, last check 19.6460ms, avail_min 2.5000ms max buf 250.0000ms, pfilled 0.0000ms, cfilled 0.0000ms job started before 0.0310ms Poll FD initialization failed. Is this error understood? I would have thought that enough others would also have been wanting to use alsaloop in such a simple configuration, to warrant a better error message. I'm somewhat confused by the alsaloop manual page, my version says it is from "5 Aug 2010" but it has glaring errors, it says "-B" is a synonym for "--buffer" but alsaloop tells me "alsaloop: invalid option -- 'B'". Also it says that I can use "-c" to set both channels and rate. Are these typos really unfixed for eight years? Here are the commands I used: $ alsaloop -C hubcap -P hw:0 -v -v -U |& tee alsaloloop.out ... $ aplay -v test.wav |& tee aplay.out ... $ cat /proc/asound/version Advanced Linux Sound Architecture Driver Version k4.14.71-1-lts. The earlier version of this email had output files attached, but they caused the message to be held for "moderator approval". Here are some HTTP versions of the same files: alsaloop.out: http://ix.io/1pUj aplay.out: http://ix.io/1pUk asound-remote (the config): http://ix.io/1pUl I think I'll investigate network audio with JACK next but I wanted to share my experiences in case there is something I'm doing wrong here, or in case there are bugs that can be fixed in ALSA. Thank you, Frederick _______________________________________________ Alsa-devel mailing list Alsa-devel@xxxxxxxxxxxxxxxx http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
