On Thu, 30 Mar 2017 13:42:09 +0200,
Ville Syrjälä wrote:
>
> On Wed, Mar 29, 2017 at 09:16:36PM +0000, Pandiyan, Dhinakaran wrote:
> > On Wed, 2017-03-29 at 11:50 +0300, Ville Syrjälä wrote:
> > > On Tue, Mar 07, 2017 at 04:12:52PM -0800, Dhinakaran Pandiyan wrote:
> > > > According to BSpec, "The CD clock frequency must be at least twice the
> > > > frequency of the Azalia BCLK." and BCLK is configured to 96 MHz by
> > > > default. This check is needed because BXT and GLK support cdclk
> > > > frequencies less than 192 MHz.
> > > >
> > > > Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@xxxxxxxxx>
> > > > ---
> > > > drivers/gpu/drm/i915/intel_cdclk.c | 12 ++++++++++++
> > > > 1 file changed, 12 insertions(+)
> > > >
> > > > diff --git a/drivers/gpu/drm/i915/intel_cdclk.c b/drivers/gpu/drm/i915/intel_cdclk.c
> > > > index e8c1181..7b1ac1d 100644
> > > > --- a/drivers/gpu/drm/i915/intel_cdclk.c
> > > > +++ b/drivers/gpu/drm/i915/intel_cdclk.c
> > > > @@ -1458,6 +1458,18 @@ static int bdw_adjust_min_pipe_pixel_rate(struct intel_crtc_state *crtc_state,
> > > > pixel_rate = max(432000, pixel_rate);
> > > > }
> > > >
> > > > + /* According to BSpec, "The CD clock frequency must be at least twice
> > > > + * the frequency of the Azalia BCLK." and BCLK is 96 MHz by default.
> > > > + * The check for GLK has to be adjusted as the platform can output
> > > > + * two pixels per clock.
> > > > + */
> > > > + if (crtc_state->has_audio) {
> > > > + if (IS_GEMINILAKE(dev_priv))
> > > > + pixel_rate = max(2 * 2 * 96000, pixel_rate);
> > >
> > > BTW that x2 factor for GLK looks wrong. It should be /2.
> > >
> > > https://bugs.freedesktop.org/show_bug.cgi?id=100439
> > >
> >
> > BSpec[1] says cdclk needs to be > 2*96 MHz (azalia bclk). To set a cdclk
> > > 192 MHz on GLK, we need to pass in max_pixclk = 2*192 MHz. But with a
> > factor of /2, we can end up picking 158.4 MHz or 79.2 MHz for cdclk,
> > which are lower than 192 MHz.
> >
> >
> > static int glk_calc_cdclk(int max_pixclk)
> > {
> > if (max_pixclk > 2 * 158400)
> > return 316800;
> > else if (max_pixclk > 2 * 79200)
> > return 158400;
> > else
> > return 79200;
> > }
> >
> > [1] Geminilake Clocks
> > "158.4 MHz CD (cannot be used when audio is enabled and Azalia BCLK is
> > 96 MHz)
> > 316.8 MHz CD
> > 79.2 MHz CD (exclusively for resolutions up to 1080p in low power single
> > pipe eDP/MIPI configurations, no audio support)"
>
> Argh. So it's really about the cdclk freq vs. bclk. Apparently the fact
> that the pipe can output two pixels per clock doesn't extend to the HDA
> side. OK, then the code looks correct.
>
> But how do we know the bclk is really 96Mhz? Or are we just making a
> worst case estimate here? Base on the hda spec I think bclk should typically
> be 24 MHz, but of course the hda spec is so old that it probably has
> little to do with today's realities. I guess ideally we'd like the audio
> driver to tell us what the frequency is, or we'd dig that up from
> somewhere ourselves.
>
> Hmm. AUD_FREQ_CNTRL seems to have something. 96 vs. 48 MHz. But I'm not sure
> we could trust that at boot time. Not sure if the audio driver will make
> its own choice if BCLK somewhere. Can any alsa folks help us?
Well, I'm not sure which BCLK is referred in this context, but if it's
about HD-audio (aka Azalia) BCLK, it's always 24MHz. It's the
specification, AFAIK.
Takashi
_______________________________________________
Alsa-devel mailing list
Alsa-devel@xxxxxxxxxxxxxxxx
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
