The patch
ASoC: cs35l33: Add device tree bindings file for cs35l33
has been applied to the asoc tree at
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
>From 28bbb33250ad8680c5cbf366770fdd9966b2a793 Mon Sep 17 00:00:00 2001
From: Paul Handrigan <Paul.Handrigan@xxxxxxxxxx>
Date: Mon, 20 Jun 2016 11:45:19 -0500
Subject: [PATCH] ASoC: cs35l33: Add device tree bindings file for cs35l33
Add device tree bindings file for the cs35l33 8V boosted
class D amplifier.
Signed-off-by: Paul Handrigan <Paul.Handrigan@xxxxxxxxxx>
Signed-off-by: Mark Brown <broonie@xxxxxxxxxx>
---
.../devicetree/bindings/sound/cs35l33.txt | 118 +++++++++++++++++++++
1 file changed, 118 insertions(+)
create mode 100644 Documentation/devicetree/bindings/sound/cs35l33.txt
diff --git a/Documentation/devicetree/bindings/sound/cs35l33.txt b/Documentation/devicetree/bindings/sound/cs35l33.txt
new file mode 100644
index 000000000000..bea6de7f8658
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/cs35l33.txt
@@ -0,0 +1,118 @@
+CS35L33 Speaker Amplifier
+
+Required properties:
+
+ - compatible : "cirrus,cs35l33"
+
+ - reg : the I2C address of the device for I2C
+
+ - VA-supply, VP-supply : power supplies for the device,
+ as covered in
+ Documentation/devicetree/bindings/regulator/regulator.txt.
+
+Optional properties:
+
+ - reset-gpios : gpio used to reset the amplifier
+
+ - interrupt-parent : Specifies the phandle of the interrupt controller to
+ which the IRQs from CS35L33 are delivered to.
+ - interrupts : IRQ line info CS35L33.
+ (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+ for further information relating to interrupt properties)
+
+ - cirrus,boost-ctl : Booster voltage use to supply the amp. If the value is
+ 0, then VBST = VP. If greater than 0, the boost voltage will be 3300mV with
+ a value of 1 and will increase at a step size of 100mV until a maximum of
+ 8000mV.
+
+ - cirrus,ramp-rate : On power up, it affects the time from when the power
+ up sequence begins to the time the audio reaches a full-scale output.
+ On power down, it affects the time from when the power-down sequence
+ begins to when the amplifier disables the PWM outputs. If this property
+ is not set then soft ramping will be disabled and ramp time would be
+ 20ms. If this property is set to 0,1,2,3 then ramp times would be 40ms,
+ 60ms,100ms,175ms respectively for 48KHz sample rate.
+
+ - cirrus,boost-ipk : The maximum current allowed for the boost converter.
+ The range starts at 1850000uA and goes to a maximum of 3600000uA
+ with a step size of 15625uA. The default is 2500000uA.
+
+ - cirrus,imon-adc-scale : Configures the scaling of data bits from the IMON
+ ADC data word. This property can be set as a value of 0 for bits 15 down
+ to 0, 6 for 21 down to 6, 7, for 22 down to 7, 8 for 23 down to 8.
+
+ - cirrus,hg-algo : Parameters for internal Class H/G algorithm that
+ controls the amplifier supplies.
+
+ - cirrus,mem-depth : Memory depth for the Class H/G algorithm measured in
+ LRCLK cycles. If this property is set to 0, 1, 2, or 3 then the memory
+ depths will be 1, 4, 8, 16 LRCLK cycles. The default is 16 LRCLK cycles.
+
+ cirrus,release-rate : The number of consecutive LRCLK periods before
+ allowing release condition tracking updates. The number of LRCLK periods
+ start at 3 to a maximum of 255.
+
+ - cirrus,ldo-thld : Configures the signal threshold at which the PWM output
+ stage enters LDO operation. Starts as a default value of 50mV for a value
+ of 1 and increases with a step size of 50mV to a maximum of 750mV (value of
+ 0xF).
+
+ - cirrus,ldo-path-disable : This is a boolean property. If present, the H/G
+ algorithm uses the max detection path. If not present, the LDO
+ detection path is used.
+
+ - cirrus,ldo-entry-delay : The LDO entry delay in milliseconds before the H/G
+ algorithm switches to the LDO voltage. This property can be set to values
+ from 0 to 7 for delays of 5ms, 10ms, 50ms, 100ms, 200ms, 500ms, 1000ms.
+ The default is 100ms.
+
+ - cirrus,vp-hg-auto : This is a boolean property. When set, class H/G VPhg
+ automatic updating is enabled.
+
+ - cirrus,vp-hg : Class H/G algorithm VPhg. Controls the H/G algorithm's
+ reference to the VP voltage for when to start generating a boosted VBST.
+ The reference voltage starts at 3000mV with a value of 0x3 and is increased
+ by 100mV per step to a maximum of 5500mV.
+
+ - cirrus,vp-hg-rate : The rate (number of LRCLK periods) at which the VPhg is
+ allowed to increase to a higher voltage when using VPhg automatic
+ tracking. This property can be set to values from 0 to 3 with rates of 128
+ periods, 2048 periods, 32768 periods, and 524288 periods.
+ The default is 32768 periods.
+
+ - cirrus,vp-hg-va : VA calculation reference for automatic VPhg tracking
+ using VPMON. This property can be set to values from 0 to 6 starting at
+ 1800mV with a step size of 50mV up to a maximum value of 1750mV.
+ Default is 1800mV.
+
+Example:
+
+cs35l33: cs35l33@40 {
+ compatible = "cirrus,cs35l33";
+ reg = <0x40>;
+
+ VA-supply = <&ldo5_reg>;
+ VP-supply = <&ldo5_reg>;
+
+ interrupt-parent = <&gpio8>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+ reset-gpios = <&cs47l91 34 0>;
+
+ cirrus,ramp-rate = <0x0>;
+ cirrus,boost-ctl = <0x30>; /* VBST = 8000mV */
+ cirrus,boost-ipk = <0xE0>; /* 3600mA */
+ cirrus,imon-adc-scale = <0> /* Bits 15 down to 0 */
+
+ cirrus,hg-algo {
+ cirrus,mem-depth = <0x3>;
+ cirrus,release-rate = <0x3>;
+ cirrus,ldo-thld = <0x1>;
+ cirrus,ldo-path-disable = <0x0>;
+ cirrus,ldo-entry-delay=<0x4>;
+ cirrus,vp-hg-auto;
+ cirrus,vp-hg=<0xF>;
+ cirrus,vp-hg-rate=<0x2>;
+ cirrus,vp-hg-va=<0x0>;
+ };
+};
--
2.8.1
_______________________________________________
Alsa-devel mailing list
Alsa-devel@xxxxxxxxxxxxxxxx
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
