[PATCH v6 2/2] ASoC: cs35l33: Add device tree bindings file for cs35l33

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Paul Handrigan <Paul.Handrigan@xxxxxxxxxx>

Add device tree bindings file for the cs35l33 8V boosted
class D amplifier.

Signed-off-by: Paul Handrigan <Paul.Handrigan@xxxxxxxxxx>
---
 .../devicetree/bindings/sound/cs35l33.txt          | 114 +++++++++++++++++++++
 1 file changed, 114 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/sound/cs35l33.txt

diff --git a/Documentation/devicetree/bindings/sound/cs35l33.txt b/Documentation/devicetree/bindings/sound/cs35l33.txt
new file mode 100644
index 0000000..01fa8fd
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/cs35l33.txt
@@ -0,0 +1,114 @@
+CS35L33 Speaker Amplifier
+
+Required properties:
+
+  - compatible : "cirrus,cs35l33"
+
+  - reg : the I2C address of the device for I2C
+
+  - VA-supply, VP-supply : power supplies for the device,
+    as covered in
+    Documentation/devicetree/bindings/regulator/regulator.txt.
+
+Optional properties:
+
+  - reset-gpios : gpio used to reset the amplifier
+
+  - interrupt-parent : Specifies the phandle of the interrupt controller to
+    which the IRQs from CS35L33 are delivered to.
+ -  interrupts : IRQ line info CS35L33.
+    (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+    for further information relating to interrupt properties)
+
+  - boost-ctl : Booster voltage use to supply the amp. If the value is
+    0, then VBST = VP. If greater than 0, the boost voltage will be 3300mV with
+    a value of 1 and will increase at a step size of 100mV until a maximum of
+    8000mV.
+
+  - ramp-rate : On power up, it affects the time from when the power
+    up sequence begins to the time the audio reaches a full-scale output.
+    On power down, it affects the time from when the power-down sequence
+    begins to when the amplifier disables the PWM outputs. If this property
+    is not set then soft ramping will be disabled and ramp time would be
+    20ms. If this property is set to 0,1,2,3 then ramp times would be 40ms,
+    60ms,100ms,175ms respectively for 48KHz sample rate.
+
+  - boost-ipk : The maximum current allowed for the boost converter.
+    The range starts at 1850mA (0xF0) and goes to a maximum of 3600mA (0xE0)
+    with a step size of 15.625mA. The default is 2500mA (0x90).
+
+  - hg-algo : Parameters for internal Class H/G algorithm that
+    controls the amplifier supplies.
+
+  - mem-depth : Memory depth for the Class H/G algorithm measured in LRCLK
+    cycles. If this property is set to 0, 1, 2, or 3 then the memory depths
+    will be 1, 4, 8, 16 LRCLK cycles.  The default is 16 LRCLK cycles.
+
+    release-rate : The number of consecutive LRCLK periods before allowing
+    release condition tracking updates. The number of LRCLK periods start
+    at 3 to a maximum of 255.
+
+  - ldo-thld : Configures the signal threshold at which the PWM output stage
+    enters LDO operation. Starts as a default value of 50mV for a value of 1
+    and increases with a step size of 50mV to a maximum of 750mV (value of
+    0xF).
+
+  - ldo-path-disable : This is a boolean property. If present, the H/G
+    algorithm uses the max detection path.  If not present, the LDO
+    detection path is used.
+
+  - ldo-entry-delay : The LDO entry delay in milliseconds before the H/G
+    algorithm switches to the LDO voltage.  This property can be set to values
+    from 0 to 7 for delays of 5ms, 10ms, 50ms, 100ms, 200ms, 500ms, 1000ms.
+    The default is 100ms.
+
+  - vp-hg-auto : This is a boolean property.  When set, class H/G VPhg
+    automatic updating is enabled.
+
+  - vp-hg :  Class H/G algorithm VPhg.  Controls the H/G algorithm's
+    reference to the VP voltage for when to start generating a boosted VBST.
+    The reference voltage starts at 3000mV with a value of 0x3 and is increased
+    by 100mV per step to a maximum of 5500mV.
+
+  - vp-hg-rate : The rate (number of LRCLK periods) at which the VPhg is
+    allowed to increase to a higher voltage when using VPhg automatic
+    tracking. This property can be set to values from 0 to 3 with rates of 128
+    periods, 2048 periods, 32768 periods, and 524288 periods.
+    The default is 32768 periods.
+
+  - vp-hg-va : VA calculation reference for automatic VPhg tracking using VPMON.
+    This property can be set to values from 0 to 6 starting at 1800mV with a
+    step size of 50mV up to a maximum value of 1750mV.  Default is 1800mV.
+
+
+Example:
+
+cs35l33: cs35l33@40 {
+	compatible = "cirrus,cs35l33";
+	reg = <0x40>;
+
+	VA-supply = <&ldo5_reg>;
+	VP-supply = <&ldo5_reg>;
+
+	interrupt-parent = <&gpio8>;
+	interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+	reset-gpios = <&cs47l91 34 0>;
+
+	ramp-rate = <0x0>;
+	boost-ctl = <0x30>;  /* VBST = 8000mV */
+	boost-ipk = <0xE0>; /* 3600mA */
+
+	hg-algo {
+		mem-depth = <0x3>;
+		release-rate = <0x3>;
+		hd-rm = <0xA>;
+		ldo-thld = <0x1>;
+		ldo-path-disable = <0x0>;
+		ldo-entry-delay=<0x4>;
+		vp-hg-auto;
+		vp-hg=<0xF>;
+		vp-hg-rate=<0x2>;
+		vp-hg-va=<0x0>;
+	};
+};
-- 
1.9.1

_______________________________________________
Alsa-devel mailing list
Alsa-devel@xxxxxxxxxxxxxxxx
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel



[Index of Archives]     [ALSA User]     [Linux Audio Users]     [Kernel Archive]     [Asterisk PBX]     [Photo Sharing]     [Linux Sound]     [Video 4 Linux]     [Gimp]     [Yosemite News]

  Powered by Linux