On 5/4/16 8:21 PM, Paulo Sergio wrote:
Hi list,
I've been trying to make Lenovo Yoga 2 (Model 1051F) sound work on
Android-x86/ Linux. [1]
Based on already discussed info from Christian Hartmann with members
(see [2] and [3] ) of this list and some efforts (basically patch pxa2xx
with Mika Westerberg changes, set the correct gpio int values {246 for
reset / 405 for ldoena and 342 for irq_gpio} and set LDO1 vcc suppliers)
we could have wm5102 initialized through spi / regmap (arizona code on
drivers/mfd) and register the DAI's.
I also ported a machine driver code from a kernel Lenovo made available
for a similar hardware (Lenovo yoga 2 1050 - uses the same baytrail
Z3745 and wolfson wm5102 audio) [4]
There are quite a few references in the machine driver to concepts
related to Clovertrail+ and early versions of Baytrail. I am fairly
convinced the mentions of 'BYT_COMMS_BT' or 'modem mixing' are no longer
supported with the DPCM platform driver/firmware you used.
To enable this codec it would be simpler to start with a newer machine
driver derived from the bytcr_rt5640 one, with just a basic SSP0-aif1
link for starters (+ MCLK). Better yet, do this work with a MinnowBoard
and an WM5102 eval board and test all this with more control on how the
hardware is setup.
If you stick to working directly on the Lenovo device, make sure you use
all the DSP controls set in the UCM files used for baytrail/baytrail-CR
(see github.com/plbossart/UCM).
Although machine driver is registered, we still don't have sound. Tried
some mixer settings / routes used on raspberry pi, but none help.
Application (in this case alsa / Android players) returns a "Device or
resource busy" when trying to ioctl pcm device:
04-30 13:05:07.877 1784 2078 E audio_hw_primary: out_write: error -1 - cannot prepare channel: Device or resource busy
# This is raised here (external/tinyalsa/pcm.c):
if (ioctl(pcm->fd, SNDRV_PCM_IOCTL_PREPARE) < 0)
return oops(pcm, errno, "cannot prepare channel");
Note: As pointed here [5] had to change the acpi_ipc_irq_index to 0 on
sound/soc/intel/atom/sst/sst_acpi.c because this is the 1st ACPI entry
listed on DSDT
I'm also trying to use a fw version that uses SSP0 [6] instead of SSP2
used as default - but no sound with both
I'd like some help from you in order to make this work. I've collect
several info which can be found here [7]
- /proc/asound/cards
- /proc/interrupts
- amixer controls list
- dmesg
- DSDT file (decoded with iasl)
Source code with changes made so far is available on github [8]
Any hint is appreciated
Thanks,
Paulo Sérgio Travaglia (pstglia)
[1] - https://groups.google.com/forum/#!forum/android-x86
[2] - http://www.spinics.net/lists/linux-acpi/msg58680.html
[3] - https://goo.gl/vBKOeI
[4] - http://goo.gl/zriwbw
[5] - https://bugzilla.kernel.org/show_bug.cgi?id=86581
[6] - http://thread.gmane.org/gmane.linux.alsa.devel/134554/focus=140634
[7]
- https://drive.google.com/folderview?id=0BxO6THtB865fWjVHLTFfV25ORjQ&usp=sharing
[8] - https://github.com/pstglia/linux
_______________________________________________
Alsa-devel mailing list
Alsa-devel@xxxxxxxxxxxxxxxx
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
