2010/6/14 Colin Guthrie <gmane@xxxxxxxxxxxxxx>
> 'Twas brillig, and Raymond Yau at 14/06/10 13:36 did gyre and gimble:
> > 2010/6/14 James Courtier-Dutton <james.dutton@xxxxxxxxx>
> >
> >> On 14 June 2010 11:22, Colin Guthrie <gmane@xxxxxxxxxxxxxx> wrote:
> >>> 'Twas brillig, and James Courtier-Dutton at 14/06/10 09:56 did gyre and
> >>> gimble:
> >>>> If you use "alsamixer", dB values are shown so it is easy to find the
> >>>> 0dB "sweet spot".
> >>>> I think it is pulse audio that hides this information when it combines
> >>>> two alsa mixer controls into one pulseaudio control.
> >>>
> >>> But it doesn't hide it. It's shown very clearly in the volume control
> >>> GUIs as the Base Volume.
> >>>
> >>> Do you really think that most users look at the sliders to find the 0dB
> >>> point? Does gnome-alsa-mixer (the old one) expose this information? No.
> >>> Does kmix? No. So the vast, vast majority of users do not know where
> the
> >>> 0dB point is unless they use alsamixer.... and even if the user is
> >>> advanced enough to use alsamixer, then I'd still say a proportion of
> >>> users are just looking at how far up the slider is rather than looking
> >>> specifically for 0dB.
> >>>
> >>> So I'd argue the exact opposite of your claim. That with the base
> volume
> >>> clearly presented in the GUI, the h/w 0dB spot is much, much more
> >>> obvious to the vast majority of users.
> >>>
> >>> I really think this is a vast improvement over a complex balancing act
> >>> of getting two different sliders setup to get distortion free audio!
> >>>
> >>> Col
> >>
> >> One has very different problems with capture than one does with
> playback.
> >> With capture it is important to identify which are analog controls
> >> (applied to the analog part of the circuit) and which are digital
> >> controls (applied to the digital part of the circuit)
> >> So, for capture one might wish to adjust the analog control so that
> >> the signal going into the ADC is a suitable level, but once the signal
> >> is digital, one should really not adjust it further, and just record
> >> what you have.
> >> If one was to combine these two capture controls in one PA control, it
> >> would just be wrong.
> >>
> >>
> > The AC97 recording from line-in problem seem not related to capture gain
> > since you can set capture volume to 0dB
> >
> > The HDA 's "PCM" softvol plugin is different from AC97 "PCM" Playback
> volume
> >
> > But you can change the softvol plugin to add gain to emulate the clipping
> in
> > software side if PA developers did not have ac97 sound card ( clipping
> occur
> > in hardware side )
> >
> > /usr/share/alsa/cards/HDA-Intel.conf
> >
> > HDA-Intel.pcm.front.0 {
> > @args [ CARD ]
> > @args.CARD {
> > type string
> > }
> > type softvol
> > slave.pcm {
> > type hw
> > card $CARD
> > }
> > control {
> > name "PCM Playback Volume"
> > card $CARD
> > }
> > + min_dB -46.5
> > + max_dB 12.0
> > + resolution 32
> > }
>
> I've made this change on my system and while previously my UI had no
> "Base Volume" displayed (because all my "h/w" (I include softvol in
> that) controls had their dB value >0.
>
as your card has no h/w gain, > 0dB , but the gain in softvol plugin is a
software gain (i.e. in the red region in PA "s volume scale
how can base_volume display in gnome volume control (unamplified) ?
BTW , -46.5dB to 0dB of softvol plugin is software atten ( not h/w atten )
>
> Now that this change is live, I have a base volume present in my GUI (at
> around the 64% mark with the cubic scale we've already discussed). When
> I set my volume ot the base volume, the h/w controls are all set to 0dB
> which is exactly as expected.
>
>
> I fail to see the point here? The base volume is clearly exposed to the
> as the recommended point on the scale at which no clipping occurs.
>
> I really don't get where your complaint is.
>
> Col
>
>
>
>
_______________________________________________
Alsa-devel mailing list
Alsa-devel@xxxxxxxxxxxxxxxx
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
