On Mon, May 24, 2010 at 09:08:52PM +0200, Pedro Ferreira wrote: > [ 518.740319] ehci_hcd 0000:00:1d.0: port 1 remote wakeup > [ 518.740356] usb usb2: usb resume > [ 518.740362] ehci_hcd 0000:00:1d.0: resume root hub > [ 518.770443] hub 2-0:1.0: hub_resume > [ 518.770566] ehci_hcd 0000:00:1d.0: GetStatus port 1 status 001005 > POWER sig=se0 PE CONNECT > [ 518.770573] hub 2-0:1.0: port 1: status 0503 change 0004 > [ 518.770654] hub 2-0:1.0: state 7 ports 3 chg 0002 evt 0000 > [ 518.770668] ehci_hcd 0000:00:1d.0: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT > [ 518.783066] usb 2-1: usb wakeup-resume > [ 518.783079] usb 2-1: finish resume > [ 518.783360] hub 2-1:1.0: hub_resume > [ 518.783875] hub 2-1:1.0: port 4: status 0101 change 0001 > [ 518.886614] ehci_hcd 0000:00:1d.0: reused qh f2b276c0 schedule > [ 518.886620] usb 2-1: link qh256-0001/f2b276c0 start 2 [1/0 us] > [ 518.886631] hub 2-0:1.0: resume on port 1, status 0 > [ 518.886636] hub 2-0:1.0: port 1, status 0503, change 0004, 480 Mb/s > [ 518.886642] hub 2-1:1.0: state 7 ports 8 chg 0010 evt 0000 > [ 518.886870] hub 2-1:1.0: port 4, status 0101, change 0000, 12 Mb/s > [ 518.958563] usb 2-1.4: new full speed USB device using ehci_hcd and address 9 > [ 519.049620] usb 2-1.4: ep0 maxpacket = 8 > [ 519.051086] usb 2-1.4: skipped 5 descriptors after interface > [ 519.051092] usb 2-1.4: skipped 1 descriptor after endpoint > [ 519.051096] usb 2-1.4: skipped 1 descriptor after endpoint > [ 519.051342] usb 2-1.4: default language 0x0409 > [ 519.051831] usb 2-1.4: udev 9, busnum 2, minor = 136 > [ 519.051836] usb 2-1.4: New USB device found, idVendor=0944, idProduct=0020 > [ 519.051841] usb 2-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 > [ 519.051845] usb 2-1.4: Product: KP3 > [ 519.051848] usb 2-1.4: Manufacturer: KORG INC. > [ 519.051986] usb 2-1.4: usb_probe_device > [ 519.051991] usb 2-1.4: configuration #1 chosen from 1 choice > [ 519.052155] usb 2-1.4: adding 2-1.4:1.0 (config #1, interface 0) > [ 519.052233] snd-usb-audio 2-1.4:1.0: usb_probe_interface > [ 519.052243] snd-usb-audio 2-1.4:1.0: usb_probe_interface - got id The audio features of this device are enabled at this point, at it seems the driver doesn't seem to complain. > [ 519.053360] usb 2-1.4: adding 2-1.4:1.1 (config #1, interface 1) > [ 519.053434] usb-storage 2-1.4:1.1: usb_probe_interface > [ 519.053447] usb-storage 2-1.4:1.1: usb_probe_interface - got id > [ 519.053644] scsi13 : SCSI emulation for USB Mass Storage devices > [ 519.053788] usb-storage: device found at 9 > [ 519.053793] usb-storage: waiting for device to settle before scanning > [ 524.039157] usb-storage: device scan complete > [ 524.040207] scsi 13:0:0:0: Direct-Access GENERIC KORG KP3 R/W > 0010 PQ: 0 ANSI: 2 > [ 524.042624] sd 13:0:0:0: Attached scsi generic sg2 type 0 > [ 524.048735] sd 13:0:0:0: [sdb] Attached SCSI removable disk > [ 526.268550] snd-usb-audio 2-1.4:1.0: forced unbind And here, the device is disconnected from USB, but I doubt that is related to the driver stack. The only thing I can currently think of is that the device draws too much power at this point, and a voltage brown-out causes the device to reset. Can you try a powered hub, or is this device powered by an external supply anyway? Did you successfully use it on the _same_ hardware under Windows? Daniel _______________________________________________ Alsa-devel mailing list Alsa-devel@xxxxxxxxxxxxxxxx http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
