On Monday 22 March 2010 18:19:28 ext Mark Brown wrote: > > Yes, but it also means, that the change will be not visible at all. > > I mean, if we did not update the reg_cache (when we should not write to > > the HW), than that change will be gone. > > So you will only be able to change the gain on the output, when the path > > is active? > > No, the control will have to take care of only writing to the chip when > it knows it's safe to do so. Now I start to understand what you are actually trying to say. > > Also, I think, if we can somehow prevent the gain change on the HW, when > > the associated DAPM widget is not active, we would still have the > > problem of the DAPM_MIXER. That operates from the cache, and if the > > cache has no 0 for the gain, than that will be written to the chip. > > Once again, the cache is operating below the controls transparently to > them. If the controls haven't written a value to the chip then the > write won't have gone to the register cache either and so other parts of > the system won't be affected. As far as the control layer is concerned > the register cache and the hardware are identical - I'm not sure why you > believe that they are separate. OK. I know that the concept is that the cache should be equal to the actual register content. What I'm doing is kind of misuse the fact, that the upper layers are only reading from the cache. So I intentionally 'lie' (in a controlled manner) to the control and DAPM layer about the HW status to achieve my goal. Or I can put it like I made an abstraction at the lower level. Your proposal is to make about similar abstraction, but in higher level, so the cache will actually equals to the HW status. And you are right, that this shall be handled in the core in the future for the benefit of other codecs. > Please take a look at the old PGA code I mentioned, it implements this > without any problem. The control suppresses the write unless the > widget is powered, storing the value separately. If the widget is > powered down then the registers aren't referred to at all when the > control is accessed. I did, and I did looked at that when I started to work with the twl4030 codec. It turned out not that simple for these outputs. I ended up with custom handled volume controls (stereo and one mono). > > I'm not saying that other codecs could not use some generic way (in a > > way, that you have described) to make their amps muted when they are not > > needed. What I'm saying, is that I don't see a generic way which can > > handle the TWL codec. > > Could you please be more specific about what you believe is going on > with TWL4030 here? It would really help if you could be more specific > about how you see the register cache getting updated. In any ways the output gains has to be handled with custom code no matter if the core has support for binding the volume controls to DAPM widget or not. The root of the problem is how the amplifiers are working: bit 4-5: Gain 0x0 - power down (mute) 0x1 - 6dB 0x2 - 0dB 0x3 - -6dB I don't have separate power bit. I can not just invert the range. I need to do the following: If 0 is coming, than I write that (mute, power down) If 2, than write two For 1 I write 3 For 3 I write 1 This gives nice gain range for the user space. 0x0 - power down (mute) 0x1 - -6dB 0x2 - 0dB 0x3 - 6dB When I have done these there were no other way, but to have my own custom calls to handle the situation, and going for DAPM PGA would also mean that I actually need to duplicate the PGA code partially in the twl4030 codec. Yes, this is a workaround, or a controlled hack to achieve what I believe is a good thing for this codec, and since I did not found a way to handle these particular registers in the core (in a way that it would have been beneficial for others as well), this was the result. I have thought about the things, that you wrote, and you are right, if the register for controlling the gain is 'sane', than there is no problem to have generic core level handling such situations. When my time allows, I can take a look at that. Thanks for taking the v2 patch! Thank you, Péter _______________________________________________ Alsa-devel mailing list Alsa-devel@xxxxxxxxxxxxxxxx http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
