From: Barry Song <barry.song@xxxxxxxxxx> Some of the Blackfin options don't directly follow the kconfig options they depend on, so kconfig is unable to display the proper tree. So sort the options such they expand/collapse properly. Signed-off-by: Barry Song <barry.song@xxxxxxxxxx> Signed-off-by: Mike Frysinger <vapier@xxxxxxxxxx> --- sound/soc/blackfin/Kconfig | 98 ++++++++++++++++++++++---------------------- 1 files changed, 49 insertions(+), 49 deletions(-) diff --git a/sound/soc/blackfin/Kconfig b/sound/soc/blackfin/Kconfig index ac927ff..f91dcb1 100644 --- a/sound/soc/blackfin/Kconfig +++ b/sound/soc/blackfin/Kconfig @@ -7,15 +7,6 @@ config SND_BF5XX_I2S mode (supports single stereo In/Out). You will also need to select the audio interfaces to support below. -config SND_BF5XX_TDM - tristate "SoC I2S(TDM mode) Audio for the ADI BF5xx chip" - depends on (BLACKFIN && SND_SOC) - help - Say Y or M if you want to add support for codecs attached to - the Blackfin SPORT (synchronous serial ports) interface in TDM - mode. - You will also need to select the audio interfaces to support below. - config SND_BF5XX_SOC_SSM2602 tristate "SoC SSM2602 Audio support for BF52x ezkit" depends on SND_BF5XX_I2S @@ -41,6 +32,31 @@ config SND_BFIN_AD73311_SE Enter the GPIO used to control AD73311's SE pin. Acceptable values are 0 to 7 +config SND_BF5XX_TDM + tristate "SoC I2S(TDM mode) Audio for the ADI BF5xx chip" + depends on (BLACKFIN && SND_SOC) + help + Say Y or M if you want to add support for codecs attached to + the Blackfin SPORT (synchronous serial ports) interface in TDM + mode. + You will also need to select the audio interfaces to support below. + +config SND_BF5XX_SOC_AD1836 + tristate "SoC AD1836 Audio support for BF5xx" + depends on SND_BF5XX_TDM + select SND_BF5XX_SOC_TDM + select SND_SOC_AD1836 + help + Say Y if you want to add support for SoC audio on BF5xx STAMP/EZKIT. + +config SND_BF5XX_SOC_AD1938 + tristate "SoC AD1938 Audio support for Blackfin" + depends on SND_BF5XX_TDM + select SND_BF5XX_SOC_TDM + select SND_SOC_AD1938 + help + Say Y if you want to add support for AD1938 codec on Blackfin. + config SND_BF5XX_AC97 tristate "SoC AC97 Audio for the ADI BF5xx chip" depends on BLACKFIN @@ -71,6 +87,30 @@ config SND_BF5XX_MULTICHAN_SUPPORT Say y if you want AC97 driver to support up to 5.1 channel audio. this mode will consume much more memory for DMA. +config SND_BF5XX_HAVE_COLD_RESET + bool "BOARD has COLD Reset GPIO" + depends on SND_BF5XX_AC97 + default y if BFIN548_EZKIT + default n if !BFIN548_EZKIT + +config SND_BF5XX_RESET_GPIO_NUM + int "Set a GPIO for cold reset" + depends on SND_BF5XX_HAVE_COLD_RESET + range 0 159 + default 19 if BFIN548_EZKIT + default 5 if BFIN537_STAMP + default 0 + help + Set the correct GPIO for RESET the sound chip. + +config SND_BF5XX_SOC_AD1980 + tristate "SoC AD1980/1 Audio support for BF5xx" + depends on SND_BF5XX_AC97 + select SND_BF5XX_SOC_AC97 + select SND_SOC_AD1980 + help + Say Y if you want to add support for SoC audio on BF5xx STAMP/EZKIT. + config SND_BF5XX_SOC_SPORT tristate @@ -88,30 +128,6 @@ config SND_BF5XX_SOC_AC97 select SND_SOC_AC97_BUS select SND_BF5XX_SOC_SPORT -config SND_BF5XX_SOC_AD1836 - tristate "SoC AD1836 Audio support for BF5xx" - depends on SND_BF5XX_TDM - select SND_BF5XX_SOC_TDM - select SND_SOC_AD1836 - help - Say Y if you want to add support for SoC audio on BF5xx STAMP/EZKIT. - -config SND_BF5XX_SOC_AD1980 - tristate "SoC AD1980/1 Audio support for BF5xx" - depends on SND_BF5XX_AC97 - select SND_BF5XX_SOC_AC97 - select SND_SOC_AD1980 - help - Say Y if you want to add support for SoC audio on BF5xx STAMP/EZKIT. - -config SND_BF5XX_SOC_AD1938 - tristate "SoC AD1938 Audio support for Blackfin" - depends on SND_BF5XX_TDM - select SND_BF5XX_SOC_TDM - select SND_SOC_AD1938 - help - Say Y if you want to add support for AD1938 codec on Blackfin. - config SND_BF5XX_SPORT_NUM int "Set a SPORT for Sound chip" depends on (SND_BF5XX_I2S || SND_BF5XX_AC97 || SND_BF5XX_TDM) @@ -120,19 +136,3 @@ config SND_BF5XX_SPORT_NUM default 0 help Set the correct SPORT for sound chip. - -config SND_BF5XX_HAVE_COLD_RESET - bool "BOARD has COLD Reset GPIO" - depends on SND_BF5XX_AC97 - default y if BFIN548_EZKIT - default n if !BFIN548_EZKIT - -config SND_BF5XX_RESET_GPIO_NUM - int "Set a GPIO for cold reset" - depends on SND_BF5XX_HAVE_COLD_RESET - range 0 159 - default 19 if BFIN548_EZKIT - default 5 if BFIN537_STAMP - default 0 - help - Set the correct GPIO for RESET the sound chip. -- 1.6.5.rc2 _______________________________________________ Alsa-devel mailing list Alsa-devel@xxxxxxxxxxxxxxxx http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
