On Tuesday 14 April 2009 14:20:04 Nikula Jarkko (Nokia-D/Helsinki) wrote:
> On Tue, 14 Apr 2009 12:34:33 +0200
>
> I meant something like this below integrating your FWID(0) and temp_fmt
> from my earlier commit da6320becf31c40b60d4b1dc6b339c9a766b671c so that
> SND_SOC_DAIFMT_DSP_B | SND_SOC_DAIFMT_NB_NF will produce correct format.
>
> I tested this only with Beagle McBSP3 and oscilloscope but I like to verify
> it with real codecs as well :-)
>
>
> Jarkko
>
> diff --git a/sound/soc/omap/omap-mcbsp.c b/sound/soc/omap/omap-mcbsp.c
> index d6882be..c40ea21 100644
> --- a/sound/soc/omap/omap-mcbsp.c
> +++ b/sound/soc/omap/omap-mcbsp.c
> @@ -272,7 +272,7 @@ static int omap_mcbsp_dai_hw_params(struct
> snd_pcm_substream *substream, break;
> case SND_SOC_DAIFMT_DSP_B:
> regs->srgr2 |= FPER(wlen * channels - 1);
> - regs->srgr1 |= FWID(wlen * channels - 2);
> + regs->srgr1 |= FWID(0);
> break;
> }
>
> @@ -291,6 +291,7 @@ static int omap_mcbsp_dai_set_dai_fmt(struct
> snd_soc_dai *cpu_dai, {
> struct omap_mcbsp_data *mcbsp_data = to_mcbsp(cpu_dai->private_data);
> struct omap_mcbsp_reg_cfg *regs = &mcbsp_data->regs;
> + unsigned int temp_fmt = fmt;
>
> if (mcbsp_data->configured)
> return 0;
> @@ -317,6 +318,8 @@ static int omap_mcbsp_dai_set_dai_fmt(struct
> snd_soc_dai *cpu_dai, /* 0-bit data delay */
> regs->rcr2 |= RDATDLY(0);
> regs->xcr2 |= XDATDLY(0);
> + /* Invert bit clock and FS polarity configuration */
> + temp_fmt ^= SND_SOC_DAIFMT_IB_IF;
> break;
> default:
> /* Unsupported data format */
> @@ -340,7 +343,7 @@ static int omap_mcbsp_dai_set_dai_fmt(struct
> snd_soc_dai *cpu_dai, }
>
> /* Set bit clock (CLKX/CLKR) and FS polarities */
> - switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
> + switch (temp_fmt & SND_SOC_DAIFMT_INV_MASK) {
> case SND_SOC_DAIFMT_NB_NF:
> /*
> * Normal BCLK + FS.
In case of the osk5912 board with tlv320aic32 codec, than you need to
configure it like this?
snd_soc_dai_set_fmt(cpu_dai,
SND_SOC_DAIFMT_DSP_B |
SND_SOC_DAIFMT_IB_NF | /* invert bclk + nor frm */
SND_SOC_DAIFMT_CBM_CFM);
Btw, what does:
inverted bclk
normal bclk
inverted frm
normal frm
actually means?
Is it so that it is:
inverted bclk:
sample is driven on the rising edge, sampled on the falling edge
normal bclk:
sample is driven on the falling edge, sampled on the rising edge
inverted frm:
FS is active high
normal frm:
FS is active low
--
Péter
_______________________________________________
Alsa-devel mailing list
Alsa-devel@xxxxxxxxxxxxxxxx
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
