On Sat, Jan 10, 2009 at 10:39:05PM +0100, Stefanie wrote:
> Hello!
>
> I have problems with the sound chip of my notebook. It is a Medion akoya
> WIM 2220. Actually, there is a driver for the chip, but somehow, I can't
> get it to work. I'm desperate and don't know what to do.
>
> My friend helped my to gather the following information:
>
> This is from lspci:
>
> 00:1b.0 0403: 8086:284b (rev 04)
>
> 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio
> Controller (rev 04)
> Subsystem: Wistron Corp. Device 4085
> Flags: fast devsel, IRQ 22
> Memory at fa200000 (64-bit, non-prefetchable) [size=16K]
> Capabilities: [50] Power Management version 2
> Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+
> Count=1/1 Enable-
> Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00
> Capabilities: [100] Virtual Channel <?>
> Capabilities: [130] Root Complex Link <?>
> Kernel modules: snd-hda-intelk <?>
>
> I have found this in my syslog while trying to load snd-hda-intel:
>
> Jan 10 21:30:16 Mescalin HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22
> (level, low) -> IRQ 22
> Jan 10 21:30:16 Mescalin HDA Intel 0000:00:1b.0: setting latency timer to 64
> Jan 10 21:30:16 Mescalin hda_codec: Unknown model for ALC268, trying
> auto-probe from BIOS...
> Jan 10 21:30:16 Mescalin hda_codec: Cannot set up configuration from
> BIOS. Using base mode...
> Jan 10 21:30:16 Mescalin SPDIF already defined
> Jan 10 21:30:16 Mescalin HDA Intel 0000:00:1b.0: PCI INT A disabled
> Jan 10 21:30:16 Mescalin HDA Intel: probe of 0000:00:1b.0 failed with
> error -16
Hi Stefanie,
There are some pre-defined models for ALC268:
static const char *alc268_models[ALC268_MODEL_LAST] = {
[ALC267_QUANTA_IL1] = "quanta-il1",
[ALC268_3ST] = "3stack",
[ALC268_TOSHIBA] = "toshiba",
[ALC268_ACER] = "acer",
[ALC268_ACER_DMIC] = "acer-dmic",
[ALC268_ACER_ASPIRE_ONE] = "acer-aspire",
[ALC268_DELL] = "dell",
[ALC268_ZEPTO] = "zepto",
#ifdef CONFIG_SND_DEBUG
[ALC268_TEST] = "test",
#endif
[ALC268_AUTO] = "auto",
};
You can try them with commands like
modprobe snd-hda-intel model=3stack
and report the one works for you, so that we integrate this knowledge
into future kernel versions.
You are also welcome to provide your hardware information by running
http://www.alsa-project.org/alsa-info.sh
and upload the data collected by it.
Thanks,
Fengguang
_______________________________________________
Alsa-devel mailing list
Alsa-devel@xxxxxxxxxxxxxxxx
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
