On Thu, Dec 07, 2023 at 04:29:29PM -0600, Pierre-Louis Bossart wrote: > +Addressing restrictions > +----------------------- > + > +The Device Number specified in the Header follows the SoundWire > +definitions, and broadcast and group addressing are > +permitted. However, in reality it is very unlikely that the exact same > +binary data needs to be provided to the two different Peripheral > +devices. The Linux implementation only allows for transfers to a > +single device at a time. For the firmware download case it seems likely that this won't always be the case, but it's definitely a thing that could be done incrementally. > +Regmap use > +~~~~~~~~~~ > +Existing codec drivers rely on regmap to download firmware to > +Peripherals, so at a high-level it would seem natural to combine BRA > +and regmap. The regmap layer could check if BRA is available or not, > +and use a regular read-write command channel in the latter case. > +However, the regmap layer does not have information on latency or how > +critical a BRA transfer is. It would make more sense to let the codec > +driver make decisions (wait, timeout, fallback to regular > +read/writes). These don't seem like insurmountable obstacles - they feel more like a copy break kind of situation where we can infer things from the pattern of transactions, and there's always the possibility of adding some calls to give regmap more high level information about the overall state of the device. One of the expected usage patterns with cache only mode is to build up a final register state then let the cache code work out the optimal pattern to actually write that out. > +In addition, the hardware may lose context and ask for the firmware to > +be downloaded again. The firmware is not however a fixed definition, > +the SDCA definition allows the hardware to request an updated firmware > +or a different coefficient table to deal with specific environment > +conditions. In other words, traditional regmap cache management is not > +good enough, the Peripheral driver is required track hardware > +notifications and react accordingly. I might be missing something but those requests for redownload sound like things that would occur regardless of the mechanism used to perform the I/O? > +Concurrency between BRA and regular read/write > +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ > +The existing 'nread/nwrite' API already relies on a notion of start > +address and number of bytes, so it would be possible to extend this > +API with a 'hint' requesting BPT/BRA be used. > +However BRA transfers could be quite long, and the use of a single > +mutex for regular read/write and BRA is a show-stopper. Independent > +operation of the control/command and BRA transfers is a fundamental > +requirement, e.g. to change the volume level with the existing regmap > +interface while downloading firmware. > +This places the burden on the codec driver to verify that there is no > +concurrent access to the same address with the command/control > +protocol and the BRA protocol. This makes me feel very nervous about robustness. I do note that regmap has an async interface which is currently only used for SPI and really only by the Cirrus DSPs (plus opportunisticly by rbtree cache sync), the original usage was to fill the pipleine of SPI controllers so we can ideally push data entirely from interrupt. TBH that was done before SMP became standard and it's a lot less clear in this day and age that this is actually helpful, the overhead of cross core synchronisation likely obliterates any benefit. There's sufficently few users that we could make API changes readily to fit better. > +One possible strategy to speed-up all initialization tasks would be to > +start a BRA transfer for firmware download, then deal with all the > +"regular" read/writes in parallel with the command channel, and last > +to wait for the BRA transfers to complete. This would allow for a > +degree of overlap instead of a purely sequential solution. As a > +results, the BRA API must support async transfers and expose a > +separate wait function. This feels a lot like it could map onto the regmap async interface, it would need a bit of a rework (mainly that currently they provide ordering guarantees with respect to both each other and sync I/O) but those could be removed with some care) but it's got the "here's a list of I/O, here's another call to ensure it's all actually happened" thing. It sounds very much like how I was thinking of the async API when I was writing it and the initial users. It's this bit that really got me thinking it could fit well into regmap. > +Error handling > +~~~~~~~~~~~~~~ > + > +The expected response to a 'bra_message' and follow-up behavior may > +vary: > + > + (1) A Peripheral driver may want to receive an immediate -EBUSY > + response if the BRA protocol is not available at a given time. > + > + (2) A Peripheral driver may want to wait until a timeout for the > + on-going transfer to be handled > + > + (3) A Peripheral driver may want to wait until existing BRA > + transfers complete or deal with BRA as a background task when > + audio transfers stop. In this case, there would be no timeout, > + and the operation may not happen if the platform is suspended. Option 3 would be a jump for regmap.
Attachment:
signature.asc
Description: PGP signature
