RE: [EXTERNAL] Re: [PATCH v3] ASoC: tas2781: Add tas2781 driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 

--- Begin Message --- 
Hi Brown
Thanks for your comments. You will rework and upstream immediately.
DT document has been already prepared, once the code has been upstream successfully, DT document will be done soon.

As to the comment on global mode, the mode is used for downloading the dsp firmware in multiple devices cases, all the 
devices can share the same generic i2c address in order to download the firmware simultaneously to save downloading firmware time consumption.
I will add the comment for this part in the code.

As to the comment on page changing, this code only handles book changing, no extra code for page changing, 
all the page changings are handled automatically by the kernel system.

-----Original Message-----
From: Mark Brown <broonie@xxxxxxxxxx> 
Sent: Wednesday, March 8, 2023 4:48 AM
To: Kevin Lu <luminlong@xxxxxxx>
Cc: lgirdwood@xxxxxxxxx; perex@xxxxxxxx; pierre-louis.bossart@xxxxxxxxxxxxxxx; tiwai@xxxxxxxx; Lu, Kevin <kevin-lu@xxxxxx>; Ding, Shenghao <shenghao-ding@xxxxxx>; alsa-devel@xxxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx
Subject: [EXTERNAL] Re: [PATCH v3] ASoC: tas2781: Add tas2781 driver

On Mon, Feb 27, 2023 at 11:38:11PM +0800, Kevin Lu wrote:
> Create tas2781 driver.

Quite a few comments below, a lot of them are fairly simple stylistic ones rather than substantial things but there are a few bigger things.
A lot of the bigger comments are essentially that the driver is doing more work than it needs to be and could either stop doing things that seem redundant or use generic functionality.

The bulk of the code looks good though.

> 
> ---
> Changes in v3:
>  - fixed issues reported-by: kernel test robot <lkp@xxxxxxxxx>
>  - correct all the inconsistent indenting warnings
>  - correct uninitialized symbol 'pwr_state'
>  - correct unsigned 'val' is never less than zero
>  - correct 'tas_dev' could be null
> 
> Signed-off-by: Kevin Lu <luminlong@xxxxxxx>

Your signoff needs to go before the ---, tooling will remove anything after the --- but your signoff needs to stay.

>  snd-soc-tas2562-objs := tas2562.o
>  snd-soc-tas2764-objs := tas2764.o
>  snd-soc-tas2780-objs := tas2780.o
> +snd-soc-tas2781-objs :=	tas2781-i2c.o tas2781-dsp.o
>  # Mux

Please keep the blank line in the file.

> --- /dev/null
> +++ b/sound/soc/codecs/tas2781-dsp.c
> @@ -0,0 +1,2261 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * ALSA SoC Texas Instruments TAS2781 Audio Smart Amplifier
> + *

Please make the entire comment block a C++ one so things look more intentional.

> +static const unsigned char crc8_lookup_table[CRC8_TABLE_SIZE] = {
> +	0x00, 0x4D, 0x9A, 0xD7, 0x79, 0x34, 0xE3, 0xAE,
> +	0xF2, 0xBF, 0x68, 0x25, 0x8B, 0xC6, 0x11, 0x5C,

Should the driver be using one of the crc8_populate_() functions here?

> +	ret = check_yram(&crc_data, book, page, reg, len);
> +	dev_info(tasdevice->dev,
> +		"isYRAM: Bk 0x%02x, Pg 0x%02x, Rg 0x%02x\n",
> +		book, page, reg);
> +	dev_info(tasdevice->dev,
> +		"isYRAM: crc_data.mnLen 0x%x, len 0x%x, nResult %d\n",
> +		crc_data.len, len, ret);

There's a lot of logging in this firmware load code which should at least be reduced to dbg level if not vdbg, it's pretty loud and it looks like at least some of it can be triggered after initial boot.

> +/* max. length of the alsa mixer control name */
> +#define MAX_CONTROL_NAME		(48)

This should be coming from the ALSA headers.


> +{
> +	struct tasdevice_priv *tas_dev =
> +		(struct tasdevice_priv *)pContext;

The kernel doesn't gennerally use hungarian notation (I see a bunch of it in the driver, n_result and p_tasdevice for example), and if there's a need to cast away from void that usually means something's gone wrong
- it looks unneeded here so you can just remove the cast.

> +	if (config_offset + 4 > (int)config_size) {
> +		dev_err(tas_dev->dev,
> +			"add config: Out of memory\n");

This isn't OOM though?

> +	cfg_info->blk_data = kcalloc(
> +		cfg_info->nblocks, sizeof(struct tasdev_blk_data *),
> +		GFP_KERNEL);
> +	if (!cfg_info->blk_data) {
> +		dev_err(tas_dev->dev,
> +			"add config: blk_data alloc failed!\n");

No need to log failures to allocate, the kernel is already pretty loud when it runs out of memory.

> +static int tas2781_digital_getvol(struct snd_kcontrol *kcontrol,
> +       struct snd_ctl_elem_value *ucontrol)

> +	/* Read the primary device as the whole */
> +	ret = tasdevice_dev_read(tas_dev, 0, mc->reg, &val);
> +	if (ret) {
> +		dev_err(tas_dev->dev,
> +		"%s, get digital vol error\n",
> +		__func__);
> +		goto out;

Your regmap looked like it already had paging support so I'm not clear why this is a custom control - can't you just use the standard ASoC helpers, the regmap paging support will work for paged register maps?

> +	}
> +	val = (val > mc->max) ? mc->max : val;
> +	val = mc->invert ? mc->max - val : val;

Please write normal conditional statements, they're easier to read than the ternery opreator.

> +static int tas2781_digital_putvol(struct snd_kcontrol *kcontrol,
> +	struct snd_ctl_elem_value *ucontrol) {
> +	struct snd_soc_component *codec
> +		= snd_soc_kcontrol_component(kcontrol);
> +	struct tasdevice_priv *tas_dev =
> +		snd_soc_component_get_drvdata(codec);
> +	struct soc_mixer_control *mc =
> +		(struct soc_mixer_control *)kcontrol->private_value;
> +	int val;
> +	int i, ret = 0;

Please run the mixer-test selftest on a card with this device, it'll tell you that this function doesn't return 1 on value changes so doesn't generate events for changes.  Similar issues with a lot of other custom controls.

> +static const struct snd_kcontrol_new tas2781_snd_controls[] = {
> +	SOC_SINGLE_RANGE_EXT_TLV("Amp Gain Volume", TAS2781_AMP_LEVEL,
> +		1, 0, 20, 0, tas2781_amp_getvol,
> +		tas2781_amp_putvol, amp_vol_tlv),
> +	SOC_SINGLE_RANGE_EXT_TLV("Digital Volume Control", TAS2781_DVC_LVL,
> +		0, 0, 200, 1, tas2781_digital_getvol,
> +		tas2781_digital_putvol, dvc_tlv),

Control names for volumes should end with Volume, see control-names.rst.

> +static int tasdevice_info_programs(struct snd_kcontrol *kcontrol,
> +			struct snd_ctl_elem_info *uinfo)
> +{
> +	struct snd_soc_component *codec
> +		= snd_soc_kcontrol_component(kcontrol);
> +	struct tasdevice_priv *p_tasdevice =
> +		snd_soc_component_get_drvdata(codec);
> +	struct tasdevice_fw *tas_fw = p_tasdevice->fmw;
> +
> +	uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
> +	/* Codec Lock Hold*/
> +	mutex_lock(&p_tasdevice->codec_lock);
> +	uinfo->count = 1;
> +	uinfo->value.integer.min = 0;
> +	uinfo->value.integer.max = (int)tas_fw->n_programs;
> +	/* Codec Lock Release*/
> +	mutex_unlock(&p_tasdevice->codec_lock);

Why does this need a lock - what might be changing?  The casting is suspicious too.

> +static void tasdevice_rca_ready(const struct firmware *fmw,
> +	void *context)
> +{

> +	mutex_lock(&tas_dev->codec_lock);
> +	rca = &(tas_dev->rcabin);
> +	fw_hdr = &(rca->fw_hdr);
> +	if (unlikely(!fmw) || unlikely(!fmw->data)) {

If you're not in a *very* hot path it's seldom useful to annotate with
likely() or unlikely().

> +static void tasdevice_enable_irq(
> +	struct tasdevice_priv *tas_dev, bool enable) {
> +	if (enable) {
> +		if (tas_dev->irq_info.is_irq_enable)
> +			return;
> +		if (gpio_is_valid(tas_dev->irq_info.irq_gpio))
> +			enable_irq(tas_dev->irq_info.irq);
> +		tas_dev->irq_info.is_irq_enable = true;

The driver shouldn't need to care if the interrupt is implemented with something that can also be a GPIO, and indeed I can't see anything that actually looks at the GPIO other than these checks.  The check for double enalbes also seems suspicious, I don't think it's needed but...

> +	} else {
> +		if (gpio_is_valid(tas_dev->irq_info.irq_gpio))
> +			disable_irq_nosync(tas_dev->irq_info.irq);

...it's certainly not matched in the disable path.  In general it looks like this function is just redundant and could be replaced by
enable_irq()/disable_irq() calls in the callers, though I'm not sure it's needed at all.

> +static void tasdevice_set_power_state(
> +	struct tasdevice_priv *tas_dev, int state) {
> +	switch (state) {
> +	case 0:
> +		schedule_delayed_work(&tas_dev->tuning_switch_wrk,
> +			msecs_to_jiffies(20));
> +		break;
> +	default:
> +		if (!(tas_dev->pstream || tas_dev->cstream)) {
> +			if (tas_dev->irq_work_func)
> +				tasdevice_enable_irq(tas_dev, false);
> +			tasdevice_select_cfg_blk(tas_dev,
> +				tas_dev->rcabin.profile_cfg_id,
> +				TASDEVICE_BIN_BLK_PRE_SHUTDOWN);
> +		}
> +		break;
> +	}

It's really not clear what thisis supposed to do - what are the two power states here?

> +static int tasdevice_dapm_event(struct snd_soc_dapm_widget *w,
> +			struct snd_kcontrol *kcontrol, int event) {
> +	struct snd_soc_component *codec = snd_soc_dapm_to_component(w->dapm);
> +	struct tasdevice_priv *tas_dev = snd_soc_component_get_drvdata(codec);
> +	int stream;
> +
> +	/* Codec Lock Hold */
> +	mutex_lock(&tas_dev->codec_lock);
> +	stream = strcmp(w->name, "SPK") ? SNDRV_PCM_STREAM_PLAYBACK :
> +		SNDRV_PCM_STREAM_CAPTURE;
> +
> +	switch (event) {
> +	case SND_SOC_DAPM_POST_PMU:
> +		dev_info(tas_dev->dev, "SND_SOC_DAPM_POST_PMU\n");

dev_info() on DAPM events is going to be way too noisy, there's a lot of logging in the core so you can probably just remove this.

> +	case SND_SOC_DAPM_PRE_PMD:
> +		dev_info(tas_dev->dev, "SND_SOC_DAPM_PRE_PMD\n");
> +		/* stop DSP only when both playback and capture streams
> +		 * are deactivated
> +		 */
> +		if (stream == SNDRV_PCM_STREAM_PLAYBACK)
> +			tas_dev->pstream = 0;
> +		else
> +			tas_dev->cstream = 0;
> +		if (tas_dev->pstream != 0 || tas_dev->cstream != 0)
> +			goto out;

It would probably be easier to have a supply widget that feeds both the ASI and speaker widgets, that way DAPM will reference count for you and the driver can just handle the event without these checks.

> +static int tasdevice_hw_params(struct snd_pcm_substream *substream,
> +	struct snd_pcm_hw_params *params, struct snd_soc_dai *dai) {
> +	struct tasdevice_priv *tas_dev = snd_soc_dai_get_drvdata(dai);
> +	unsigned int fsrate;
> +	unsigned int slot_width;
> +	int bclk_rate;
> +	int rc = 0;
> +
> +	dev_info(tas_dev->dev, "%s: %s\n",
> +		__func__, substream->stream == SNDRV_PCM_STREAM_PLAYBACK ?
> +		"Playback":"Capture");

Again, too much logging.  The driver should be silent during normal operation - some logging on boot or error is fine but userspace shouldn't be able to spam the logs and hide other information.

> +static int tasdevice_set_dai_sysclk(struct snd_soc_dai *codec_dai,
> +	int clk_id, unsigned int freq, int dir) {
> +	struct tasdevice_priv *tas_dev = snd_soc_dai_get_drvdata(codec_dai);
> +
> +	dev_info(tas_dev->dev,
> +		"%s: clk_id = %d, freq = %u, CLK direction %s\n",
> +		__func__, clk_id, freq,
> +		dir == TASDEVICE_CLK_DIR_OUT ? "OUT":"IN");
> +
> +	return 0;
> +}

You can just remove this, it doesn't do anything except log.

> +static void tasdevice_codec_remove(
> +	struct snd_soc_component *codec)
> +{

Weird indentation here.

> +static void irq_work_routine(struct work_struct *pWork) {
> +	struct tasdevice_priv *tas_dev =
> +		container_of(pWork, struct tasdevice_priv,
> +		irq_info.irq_work.work);
> +
> +	mutex_lock(&tas_dev->codec_lock);
> +	if (tas_dev->runtime_suspend) {
> +		dev_info(tas_dev->dev, "%s, Runtime Suspended\n", __func__);
> +		goto end;
> +	}
> +	/*Logical Layer IRQ function, return is ignored*/
> +	if (tas_dev->irq_work_func)
> +		tas_dev->irq_work_func(tas_dev);
> +	else
> +		dev_info(tas_dev->dev,
> +			"%s, irq_work_func is NULL\n", __func__);
> +end:
> +	mutex_unlock(&tas_dev->codec_lock);
> +}

There is only one function that's ever assigned for the irq_work_func, just inline it and don't bother with the pointer in the driver structure - that should be a lot simpler.

> +static void tas2781_irq_work_func(struct tasdevice_priv *tas_dev) {
> +	int rc = 0;
> +	unsigned int reg_val = 0, array_size = 0, i = 0, ndev = 0;
> +	unsigned int int_reg_array[] = {
> +		TAS2781_REG_INT_LTCH0,
> +		TAS2781_REG_INT_LTCH1,
> +		TAS2781_REG_INT_LTCH1_0,
> +		TAS2781_REG_INT_LTCH2,
> +		TAS2781_REG_INT_LTCH3,
> +		TAS2781_REG_INT_LTCH4};
> +
> +	tasdevice_enable_irq(tas_dev, false);

It needs to be a lot clearer what will reenable the interrupt - some comments would help, I see there's some interlock with tuning_switch_routine() but I'm not clear what that does...

> +	array_size = ARRAY_SIZE(int_reg_array);
> +
> +	for (ndev = 0; ndev < tas_dev->ndev; ndev++) {
> +		for (i = 0; i < array_size; i++) {
> +			rc = tasdevice_dev_read(tas_dev,
> +				ndev, int_reg_array[i], &reg_val);
> +			if (!rc)
> +				dev_info(tas_dev->dev,
> +					"INT STATUS REG 0x%04x=0x%02x\n",
> +					int_reg_array[i], reg_val);
> +			else
> +				dev_err(tas_dev->dev,
> +					"Read Reg 0x%04x error(rc=%d)\n",
> +					int_reg_array[i], rc);
> +		}
> +	}
> +}

...and this seems to just read the interrupt status registers and log the results so do we even need to enable the interrupt?

> +static int tasdevice_parse_dt(struct tasdevice_priv *tas_dev) {
> +	struct device_node *np = tas_dev->dev->of_node;
> +	int rc = 0, i = 0, ndev = 0;
> +	unsigned int dev_addrs[max_chn];
> +	struct i2c_client *client = (struct i2c_client *)tas_dev->client;

If you're adding DT bindings you need to send a DT bindings document.

> +static int tasdevice_change_chn_book(struct tasdevice_priv *tas_dev,
> +	enum channel chn, int book)
> +{

As I said earlier the regmap uses ranges so I'm not clear why there's open coding of page changing?

> +static void tas2781_set_global_mode(struct tasdevice_priv *tas_dev) {
> +	int i = 0;
> +	int ret = 0;

What's all this global mode stuff about?  It's not clear from the code.

> +	mutex_init(&tas_dev->codec_lock);
> +	ret = devm_snd_soc_register_component(tas_dev->dev,
> +		&soc_codec_driver_tasdevice,
> +		tasdevice_dai_driver, ARRAY_SIZE(tasdevice_dai_driver));
> +	if (ret)
> +		dev_err(tas_dev->dev, "%s: codec register error:0x%08x\n",
> +			__func__, ret);
> +
> +	INIT_DELAYED_WORK(&tas_dev->irq_info.irq_work, irq_work_routine);
> +	tas_dev->irq_info.is_irq_enable = false;

Shouldn't this happen before we register with the core?

> +static int tasdevice_pm_suspend(struct device *dev) {
> +	struct tasdevice_priv *tas_dev = dev_get_drvdata(dev);
> +
> +	mutex_lock(&tas_dev->codec_lock);
> +	tas_dev->runtime_suspend = true;
> +
> +	if (tas_dev->irq_work_func) {
> +		if (delayed_work_pending(&tas_dev->irq_info.irq_work)) {
> +			dev_dbg(tas_dev->dev, "cancel IRQ work\n");
> +			cancel_delayed_work_sync(&tas_dev->irq_info.irq_work);
> +		}
> +	}

Just cancelling the work unconditionally should do the right thing, though given that there's no configuration done for the device it's unclear why we're implementing runtime suspend at all?

> +static int tasdevice_i2c_probe(struct i2c_client *i2c,
> +	const struct i2c_device_id *id)
> +{
> +	struct tasdevice_priv *tas_dev = NULL;
> +	int ret = 0;
> +
> +	if (!i2c_check_functionality(i2c->adapter, I2C_FUNC_I2C)) {
> +		dev_err(&i2c->dev,
> +			"%s: I2C check failed\n", __func__);
> +		ret = -ENODEV;
> +		goto out;
> +	}

Why the functionality check?

--- End Message ---
[Index of Archives]     [ALSA User]     [Linux Audio Users]     [Pulse Audio]     [Kernel Archive]     [Asterisk PBX]     [Photo Sharing]     [Linux Sound]     [Video 4 Linux]     [Gimp]     [Yosemite News]

  Powered by Linux