After further investigation, I realize that the total number of elements
in array is not enough to store all of related messages from device.
This commit refines meter array and message parser.
In terms of channel identifier, register DSP models are classified to
two categories:
1. the target of output is selectable
828mk2, 896hd, and Traveler are in the category. They transfer messages
with channel identifier between 0x00 and 0x13 for input meters,
therefore 20 elements are needed to store.
On the other hand, they transfer messages with channel identifier for one
pair of output meters. The selection is done by asynchronous write
transaction to offset 0x'ffff'f000'0b2c. The table for relationship
between written value and available identifiers is below:
============= ===============
written value identifier pair
============= ===============
0x00000b00 0x80/0x81
0x00000b01 0x82/0x83
... ...
0x00000b0b 0x96/0x97
... ...
0x00000b10 0xa0/0xa1
... ...
0x00000b3f 0xfe/0xff
... ...
greater 0xfe/0xff
============= ===============
Actually in the above three models, 0x96/0x97 pair is the maximum. Thus
the number of available output meter is 24.
2. all of output is available
8 pre, Ultralite, Audio Express, and 4 pre are in the category. They
transfer messages for output meters without any selection. The table for
available identifier for each direction is below:
============== ========= ==========
model input output
============== ========= ==========
8 pre 0x00-0x0f 0x82-0x8d
Ultralite 0x00-0x09 0x82-0x8f
Audio Express 0x00-0x09 0x80-0x8d
4 pre 0x00-0x09 0x80-0x8d
============== ========= ==========
Some of available identifiers might not be used for actual output meters.
Anyway, 24 plus 24 elements accommodate the input/output meters.
I note that isochronous packet from V3HD/V4HD deliver no message.
Notification by asynchronous transaction to registered address seems to be
used for the purpose as well as for change of mixer parameter.
Signed-off-by: Takashi Sakamoto <o-takashi@xxxxxxxxxxxxx>
---
include/uapi/sound/firewire.h | 5 ++++-
.../motu/motu-register-dsp-message-parser.c | 14 +++++++++-----
2 files changed, 13 insertions(+), 6 deletions(-)
diff --git a/include/uapi/sound/firewire.h b/include/uapi/sound/firewire.h
index e52a97b3ceaa..68eb0e43c052 100644
--- a/include/uapi/sound/firewire.h
+++ b/include/uapi/sound/firewire.h
@@ -141,7 +141,10 @@ struct snd_firewire_tascam_state {
* up to 12.
*/
-#define SNDRV_FIREWIRE_MOTU_REGISTER_DSP_METER_COUNT 40
+#define SNDRV_FIREWIRE_MOTU_REGISTER_DSP_METER_INPUT_COUNT 24
+#define SNDRV_FIREWIRE_MOTU_REGISTER_DSP_METER_OUTPUT_COUNT 24
+#define SNDRV_FIREWIRE_MOTU_REGISTER_DSP_METER_COUNT \
+ (SNDRV_FIREWIRE_MOTU_REGISTER_DSP_METER_INPUT_COUNT + SNDRV_FIREWIRE_MOTU_REGISTER_DSP_METER_OUTPUT_COUNT)
/**
* struct snd_firewire_motu_register_dsp_meter - the container for meter information in DSP
diff --git a/sound/firewire/motu/motu-register-dsp-message-parser.c b/sound/firewire/motu/motu-register-dsp-message-parser.c
index cbc06b3b70f6..0c587567540f 100644
--- a/sound/firewire/motu/motu-register-dsp-message-parser.c
+++ b/sound/firewire/motu/motu-register-dsp-message-parser.c
@@ -335,11 +335,15 @@ void snd_motu_register_dsp_message_parser_parse(struct snd_motu *motu, const str
else
pos = b[MSG_METER_IDX_POS_4PRE_AE];
- if (pos < 0x80)
- pos &= 0x1f;
- else
- pos = (pos & 0x1f) + 20;
- parser->meter.data[pos] = val;
+ if (pos < SNDRV_FIREWIRE_MOTU_REGISTER_DSP_METER_INPUT_COUNT) {
+ parser->meter.data[pos] = val;
+ } else if (pos >= 0x80) {
+ pos -= (0x80 - SNDRV_FIREWIRE_MOTU_REGISTER_DSP_METER_INPUT_COUNT);
+
+ if (pos < SNDRV_FIREWIRE_MOTU_REGISTER_DSP_METER_COUNT)
+ parser->meter.data[pos] = val;
+ }
+
// The message for meter is interruptible to the series of other
// types of messages. Don't cache it.
fallthrough;
--
2.30.2
