It appears that on boot, nothing gets set, but if I reload the module
it works:
ben@mythfrontend:~$ cat /proc/asound/card0/codec#1
Codec: Generic 1095 SI1390 HDMI
Address: 1
Vendor Id: 0x10951390
Subsystem Id: 0xffffffff
Revision Id: 0x100000
No Modem Function Group found
Default PCM:
rates [0x0]:
bits [0x0]:
formats [0x0]:
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x02 [Audio Output] wcaps 0x6211: Stereo Digital
Converter: stream=0, channel=0
Digital: Enabled Copyright GenLevel
Digital category: 0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
bits [0x1e]: 16 20 24 32
formats [0x5]: PCM AC3
Node 0x03 [Pin Complex] wcaps 0x40738d: Stereo Digital Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0894: OUT Detect R/L
Pin Default 0x98460010: [Fixed] SPDIF Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Connection: 1
0x02
ben@mythfrontend:~$
The unmuting looks like it's working too (Amp-Out vals: [0x00 0x00]).
I'm still not getting any sound though - my amp just says
"Detecting...".
Is the GPIO line significant? As far as I can tell from the docs, that
just means there are no GPIOs.
Ben
On 9 Mar 2008, at 00:10, Ben Firshman wrote:
> This is on 1.0.16. Forgive me if I appear clueless, I have only been
> working on this for the past few hours.
>
> In an attempt to get HDMI audio working on the AppleTV, I have added
> this line to the presets in patch_atihdmi.c:
>
> { .id = 0x10951390, .name = "SI1390 HDMI", .patch = patch_atihdmi },
>
> The device is detected fine:
>
> ben@mythfrontend:~$ aplay -l
> **** List of PLAYBACK Hardware Devices ****
> card 0: Intel [HDA Intel], device 0: ALC882 Analog [ALC882 Analog]
> Subdevices: 1/1
> Subdevice #0: subdevice #0
> card 0: Intel [HDA Intel], device 1: ALC882 Digital [ALC882 Digital]
> Subdevices: 1/1
> Subdevice #0: subdevice #0
> card 0: Intel [HDA Intel], device 3: ATI HDMI [ATI HDMI]
> Subdevices: 1/1
> Subdevice #0: subdevice #0
> ben@mythfrontend:~$
>
> and I can send audio to the device, but it doesn't work. I presume
> this because this is doing nothing:
>
> static struct hda_verb atihdmi_basic_init[] = {
> /* enable digital output on pin widget */
> { 0x03, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT },
> {} /* terminator */
> };
>
> ben@mythfrontend:~$ cat /proc/asound/card0/codec#1
> Codec: Generic 1095 SI1390 HDMI
> Address: 1
> Vendor Id: 0x10951390
> Subsystem Id: 0xffffffff
> Revision Id: 0x100000
> No Modem Function Group found
> Default PCM:
> rates [0x0]:
> bits [0x0]:
> formats [0x0]:
> Default Amp-In caps: N/A
> Default Amp-Out caps: N/A
> GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
> Node 0x02 [Audio Output] wcaps 0x6211: Stereo Digital
> Converter: stream=0, channel=0
> Digital:
> Digital category: 0x0
> PCM:
> rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
> bits [0x1e]: 16 20 24 32
> formats [0x5]: PCM AC3
> Node 0x03 [Pin Complex] wcaps 0x40738d: Stereo Digital Amp-Out
> Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
> Amp-Out vals: [0x80 0x80]
> Pincap 0x0894: OUT Detect R/L
> Pin Default 0x98460010: [Fixed] SPDIF Out at Int HDMI
> Conn = Digital, Color = Unknown
> DefAssociation = 0x1, Sequence = 0x0
> Pin-ctls: 0x00:
> Unsolicited: tag=00, enabled=0
> Connection: 1
> 0x02
>
> "Pin-ctls: 0x00:" should be reading "Pin-ctls: 0x40: OUT" should it
> not? What is wrong?
>
> Thanks
>
> Ben
>
> _______________________________________________
> Alsa-devel mailing list
> Alsa-devel@xxxxxxxxxxxxxxxx
> http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
_______________________________________________
Alsa-devel mailing list
Alsa-devel@xxxxxxxxxxxxxxxx
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
