[PATCH v2 12/12] extcon: arizona: Drop the arizona extcon driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



The codec drivers for arizona codecs now take care of jack-detect
handling themselves; and drivers/mfd/arizona-core.c no longer
instantiates a "arizona-extcon" child-device for these.

This means that the "arizona-extcon" driver is no longer needed
(there are no longer any devices for it to bind to), so it can
be dropped.

Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx>
---
 MAINTAINERS                     |    1 -
 drivers/extcon/Kconfig          |    8 -
 drivers/extcon/Makefile         |    1 -
 drivers/extcon/extcon-arizona.c | 1816 -------------------------------
 4 files changed, 1826 deletions(-)
 delete mode 100644 drivers/extcon/extcon-arizona.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 66b56928cc47..9ded82d53c18 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -19255,7 +19255,6 @@ F:	Documentation/devicetree/bindings/sound/wlf,arizona.yaml
 F:	Documentation/hwmon/wm83??.rst
 F:	arch/arm/mach-s3c/mach-crag6410*
 F:	drivers/clk/clk-wm83*.c
-F:	drivers/extcon/extcon-arizona.c
 F:	drivers/gpio/gpio-*wm*.c
 F:	drivers/gpio/gpio-arizona.c
 F:	drivers/hwmon/wm83??-hwmon.c
diff --git a/drivers/extcon/Kconfig b/drivers/extcon/Kconfig
index af58ebca2bf6..e3db936becfd 100644
--- a/drivers/extcon/Kconfig
+++ b/drivers/extcon/Kconfig
@@ -21,14 +21,6 @@ config EXTCON_ADC_JACK
 	help
 	  Say Y here to enable extcon device driver based on ADC values.
 
-config EXTCON_ARIZONA
-	tristate "Wolfson Arizona EXTCON support"
-	depends on MFD_ARIZONA && INPUT && SND_SOC
-	help
-	  Say Y here to enable support for external accessory detection
-	  with Wolfson Arizona devices. These are audio CODECs with
-	  advanced audio accessory detection support.
-
 config EXTCON_AXP288
 	tristate "X-Power AXP288 EXTCON support"
 	depends on MFD_AXP20X && USB_SUPPORT && X86 && ACPI
diff --git a/drivers/extcon/Makefile b/drivers/extcon/Makefile
index fe10a1b7d18b..1b390d934ca9 100644
--- a/drivers/extcon/Makefile
+++ b/drivers/extcon/Makefile
@@ -6,7 +6,6 @@
 obj-$(CONFIG_EXTCON)		+= extcon-core.o
 extcon-core-objs		+= extcon.o devres.o
 obj-$(CONFIG_EXTCON_ADC_JACK)	+= extcon-adc-jack.o
-obj-$(CONFIG_EXTCON_ARIZONA)	+= extcon-arizona.o
 obj-$(CONFIG_EXTCON_AXP288)	+= extcon-axp288.o
 obj-$(CONFIG_EXTCON_FSA9480)	+= extcon-fsa9480.o
 obj-$(CONFIG_EXTCON_GPIO)	+= extcon-gpio.o
diff --git a/drivers/extcon/extcon-arizona.c b/drivers/extcon/extcon-arizona.c
deleted file mode 100644
index aae82db542a5..000000000000
--- a/drivers/extcon/extcon-arizona.c
+++ /dev/null
@@ -1,1816 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * extcon-arizona.c - Extcon driver Wolfson Arizona devices
- *
- *  Copyright (C) 2012-2014 Wolfson Microelectronics plc
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/i2c.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/err.h>
-#include <linux/gpio/consumer.h>
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/platform_device.h>
-#include <linux/pm_runtime.h>
-#include <linux/property.h>
-#include <linux/regulator/consumer.h>
-#include <linux/extcon-provider.h>
-
-#include <sound/soc.h>
-
-#include <linux/mfd/arizona/core.h>
-#include <linux/mfd/arizona/pdata.h>
-#include <linux/mfd/arizona/registers.h>
-#include <dt-bindings/mfd/arizona.h>
-
-#define ARIZONA_MAX_MICD_RANGE 8
-
-#define ARIZONA_MICD_CLAMP_MODE_JDL      0x4
-#define ARIZONA_MICD_CLAMP_MODE_JDH      0x5
-#define ARIZONA_MICD_CLAMP_MODE_JDL_GP5H 0x9
-#define ARIZONA_MICD_CLAMP_MODE_JDH_GP5H 0xb
-
-#define ARIZONA_TST_CAP_DEFAULT 0x3
-#define ARIZONA_TST_CAP_CLAMP   0x1
-
-#define ARIZONA_HPDET_MAX 10000
-
-#define HPDET_DEBOUNCE 500
-#define DEFAULT_MICD_TIMEOUT 2000
-
-#define ARIZONA_HPDET_WAIT_COUNT 15
-#define ARIZONA_HPDET_WAIT_DELAY_MS 20
-
-#define QUICK_HEADPHONE_MAX_OHM 3
-#define MICROPHONE_MIN_OHM      1257
-#define MICROPHONE_MAX_OHM      30000
-
-#define MICD_DBTIME_TWO_READINGS 2
-#define MICD_DBTIME_FOUR_READINGS 4
-
-#define MICD_LVL_1_TO_7 (ARIZONA_MICD_LVL_1 | ARIZONA_MICD_LVL_2 | \
-			 ARIZONA_MICD_LVL_3 | ARIZONA_MICD_LVL_4 | \
-			 ARIZONA_MICD_LVL_5 | ARIZONA_MICD_LVL_6 | \
-			 ARIZONA_MICD_LVL_7)
-
-#define MICD_LVL_0_TO_7 (ARIZONA_MICD_LVL_0 | MICD_LVL_1_TO_7)
-
-#define MICD_LVL_0_TO_8 (MICD_LVL_0_TO_7 | ARIZONA_MICD_LVL_8)
-
-struct arizona_extcon_info {
-	struct device *dev;
-	struct arizona *arizona;
-	struct mutex lock;
-	struct regulator *micvdd;
-	struct input_dev *input;
-
-	u16 last_jackdet;
-
-	int micd_mode;
-	const struct arizona_micd_config *micd_modes;
-	int micd_num_modes;
-
-	const struct arizona_micd_range *micd_ranges;
-	int num_micd_ranges;
-
-	bool micd_reva;
-	bool micd_clamp;
-
-	struct delayed_work hpdet_work;
-	struct delayed_work micd_detect_work;
-	struct delayed_work micd_timeout_work;
-
-	bool hpdet_active;
-	bool hpdet_done;
-	bool hpdet_retried;
-
-	int num_hpdet_res;
-	unsigned int hpdet_res[3];
-
-	bool mic;
-	bool detecting;
-	int jack_flips;
-
-	int hpdet_ip_version;
-
-	struct extcon_dev *edev;
-
-	struct gpio_desc *micd_pol_gpio;
-};
-
-static const struct arizona_micd_config micd_default_modes[] = {
-	{ ARIZONA_ACCDET_SRC, 1, 0 },
-	{ 0,                  2, 1 },
-};
-
-static const struct arizona_micd_range micd_default_ranges[] = {
-	{ .max =  11, .key = BTN_0 },
-	{ .max =  28, .key = BTN_1 },
-	{ .max =  54, .key = BTN_2 },
-	{ .max = 100, .key = BTN_3 },
-	{ .max = 186, .key = BTN_4 },
-	{ .max = 430, .key = BTN_5 },
-};
-
-/* The number of levels in arizona_micd_levels valid for button thresholds */
-#define ARIZONA_NUM_MICD_BUTTON_LEVELS 64
-
-static const int arizona_micd_levels[] = {
-	3, 6, 8, 11, 13, 16, 18, 21, 23, 26, 28, 31, 34, 36, 39, 41, 44, 46,
-	49, 52, 54, 57, 60, 62, 65, 67, 70, 73, 75, 78, 81, 83, 89, 94, 100,
-	105, 111, 116, 122, 127, 139, 150, 161, 173, 186, 196, 209, 220, 245,
-	270, 295, 321, 348, 375, 402, 430, 489, 550, 614, 681, 752, 903, 1071,
-	1257, 30000,
-};
-
-static const unsigned int arizona_cable[] = {
-	EXTCON_MECHANICAL,
-	EXTCON_JACK_MICROPHONE,
-	EXTCON_JACK_HEADPHONE,
-	EXTCON_JACK_LINE_OUT,
-	EXTCON_NONE,
-};
-
-static void arizona_start_hpdet_acc_id(struct arizona_extcon_info *info);
-
-static void arizona_extcon_hp_clamp(struct arizona_extcon_info *info,
-				    bool clamp)
-{
-	struct arizona *arizona = info->arizona;
-	unsigned int mask = 0, val = 0;
-	unsigned int cap_sel = 0;
-	int ret;
-
-	switch (arizona->type) {
-	case WM8998:
-	case WM1814:
-		mask = 0;
-		break;
-	case WM5110:
-	case WM8280:
-		mask = ARIZONA_HP1L_SHRTO | ARIZONA_HP1L_FLWR |
-		       ARIZONA_HP1L_SHRTI;
-		if (clamp) {
-			val = ARIZONA_HP1L_SHRTO;
-			cap_sel = ARIZONA_TST_CAP_CLAMP;
-		} else {
-			val = ARIZONA_HP1L_FLWR | ARIZONA_HP1L_SHRTI;
-			cap_sel = ARIZONA_TST_CAP_DEFAULT;
-		}
-
-		ret = regmap_update_bits(arizona->regmap,
-					 ARIZONA_HP_TEST_CTRL_1,
-					 ARIZONA_HP1_TST_CAP_SEL_MASK,
-					 cap_sel);
-		if (ret != 0)
-			dev_warn(arizona->dev,
-				 "Failed to set TST_CAP_SEL: %d\n", ret);
-		break;
-	default:
-		mask = ARIZONA_RMV_SHRT_HP1L;
-		if (clamp)
-			val = ARIZONA_RMV_SHRT_HP1L;
-		break;
-	}
-
-	snd_soc_dapm_mutex_lock(arizona->dapm);
-
-	arizona->hpdet_clamp = clamp;
-
-	/* Keep the HP output stages disabled while doing the clamp */
-	if (clamp) {
-		ret = regmap_update_bits(arizona->regmap,
-					 ARIZONA_OUTPUT_ENABLES_1,
-					 ARIZONA_OUT1L_ENA |
-					 ARIZONA_OUT1R_ENA, 0);
-		if (ret != 0)
-			dev_warn(arizona->dev,
-				"Failed to disable headphone outputs: %d\n",
-				 ret);
-	}
-
-	if (mask) {
-		ret = regmap_update_bits(arizona->regmap, ARIZONA_HP_CTRL_1L,
-					 mask, val);
-		if (ret != 0)
-			dev_warn(arizona->dev, "Failed to do clamp: %d\n",
-				 ret);
-
-		ret = regmap_update_bits(arizona->regmap, ARIZONA_HP_CTRL_1R,
-					 mask, val);
-		if (ret != 0)
-			dev_warn(arizona->dev, "Failed to do clamp: %d\n",
-				 ret);
-	}
-
-	/* Restore the desired state while not doing the clamp */
-	if (!clamp) {
-		ret = regmap_update_bits(arizona->regmap,
-					 ARIZONA_OUTPUT_ENABLES_1,
-					 ARIZONA_OUT1L_ENA |
-					 ARIZONA_OUT1R_ENA, arizona->hp_ena);
-		if (ret != 0)
-			dev_warn(arizona->dev,
-				 "Failed to restore headphone outputs: %d\n",
-				 ret);
-	}
-
-	snd_soc_dapm_mutex_unlock(arizona->dapm);
-}
-
-static void arizona_extcon_set_mode(struct arizona_extcon_info *info, int mode)
-{
-	struct arizona *arizona = info->arizona;
-
-	mode %= info->micd_num_modes;
-
-	gpiod_set_value_cansleep(info->micd_pol_gpio,
-				 info->micd_modes[mode].gpio);
-
-	regmap_update_bits(arizona->regmap, ARIZONA_MIC_DETECT_1,
-			   ARIZONA_MICD_BIAS_SRC_MASK,
-			   info->micd_modes[mode].bias <<
-			   ARIZONA_MICD_BIAS_SRC_SHIFT);
-	regmap_update_bits(arizona->regmap, ARIZONA_ACCESSORY_DETECT_MODE_1,
-			   ARIZONA_ACCDET_SRC, info->micd_modes[mode].src);
-
-	info->micd_mode = mode;
-
-	dev_dbg(arizona->dev, "Set jack polarity to %d\n", mode);
-}
-
-static const char *arizona_extcon_get_micbias(struct arizona_extcon_info *info)
-{
-	switch (info->micd_modes[0].bias) {
-	case 1:
-		return "MICBIAS1";
-	case 2:
-		return "MICBIAS2";
-	case 3:
-		return "MICBIAS3";
-	default:
-		return "MICVDD";
-	}
-}
-
-static void arizona_extcon_pulse_micbias(struct arizona_extcon_info *info)
-{
-	struct arizona *arizona = info->arizona;
-	const char *widget = arizona_extcon_get_micbias(info);
-	struct snd_soc_dapm_context *dapm = arizona->dapm;
-	struct snd_soc_component *component = snd_soc_dapm_to_component(dapm);
-	int ret;
-
-	ret = snd_soc_component_force_enable_pin(component, widget);
-	if (ret != 0)
-		dev_warn(arizona->dev, "Failed to enable %s: %d\n",
-			 widget, ret);
-
-	snd_soc_dapm_sync(dapm);
-
-	if (!arizona->pdata.micd_force_micbias) {
-		ret = snd_soc_component_disable_pin(component, widget);
-		if (ret != 0)
-			dev_warn(arizona->dev, "Failed to disable %s: %d\n",
-				 widget, ret);
-
-		snd_soc_dapm_sync(dapm);
-	}
-}
-
-static void arizona_start_mic(struct arizona_extcon_info *info)
-{
-	struct arizona *arizona = info->arizona;
-	bool change;
-	int ret;
-	unsigned int mode;
-
-	/* Microphone detection can't use idle mode */
-	pm_runtime_get(info->dev);
-
-	if (info->detecting) {
-		ret = regulator_allow_bypass(info->micvdd, false);
-		if (ret != 0) {
-			dev_err(arizona->dev,
-				"Failed to regulate MICVDD: %d\n",
-				ret);
-		}
-	}
-
-	ret = regulator_enable(info->micvdd);
-	if (ret != 0) {
-		dev_err(arizona->dev, "Failed to enable MICVDD: %d\n",
-			ret);
-	}
-
-	if (info->micd_reva) {
-		const struct reg_sequence reva[] = {
-			{ 0x80,  0x3 },
-			{ 0x294, 0x0 },
-			{ 0x80,  0x0 },
-		};
-
-		regmap_multi_reg_write(arizona->regmap, reva, ARRAY_SIZE(reva));
-	}
-
-	if (info->detecting && arizona->pdata.micd_software_compare)
-		mode = ARIZONA_ACCDET_MODE_ADC;
-	else
-		mode = ARIZONA_ACCDET_MODE_MIC;
-
-	regmap_update_bits(arizona->regmap,
-			   ARIZONA_ACCESSORY_DETECT_MODE_1,
-			   ARIZONA_ACCDET_MODE_MASK, mode);
-
-	arizona_extcon_pulse_micbias(info);
-
-	ret = regmap_update_bits_check(arizona->regmap, ARIZONA_MIC_DETECT_1,
-				       ARIZONA_MICD_ENA, ARIZONA_MICD_ENA,
-				       &change);
-	if (ret < 0) {
-		dev_err(arizona->dev, "Failed to enable micd: %d\n", ret);
-	} else if (!change) {
-		regulator_disable(info->micvdd);
-		pm_runtime_put_autosuspend(info->dev);
-	}
-}
-
-static void arizona_stop_mic(struct arizona_extcon_info *info)
-{
-	struct arizona *arizona = info->arizona;
-	const char *widget = arizona_extcon_get_micbias(info);
-	struct snd_soc_dapm_context *dapm = arizona->dapm;
-	struct snd_soc_component *component = snd_soc_dapm_to_component(dapm);
-	bool change = false;
-	int ret;
-
-	ret = regmap_update_bits_check(arizona->regmap, ARIZONA_MIC_DETECT_1,
-				       ARIZONA_MICD_ENA, 0,
-				       &change);
-	if (ret < 0)
-		dev_err(arizona->dev, "Failed to disable micd: %d\n", ret);
-
-	ret = snd_soc_component_disable_pin(component, widget);
-	if (ret != 0)
-		dev_warn(arizona->dev,
-			 "Failed to disable %s: %d\n",
-			 widget, ret);
-
-	snd_soc_dapm_sync(dapm);
-
-	if (info->micd_reva) {
-		const struct reg_sequence reva[] = {
-			{ 0x80,  0x3 },
-			{ 0x294, 0x2 },
-			{ 0x80,  0x0 },
-		};
-
-		regmap_multi_reg_write(arizona->regmap, reva, ARRAY_SIZE(reva));
-	}
-
-	ret = regulator_allow_bypass(info->micvdd, true);
-	if (ret != 0) {
-		dev_err(arizona->dev, "Failed to bypass MICVDD: %d\n",
-			ret);
-	}
-
-	if (change) {
-		regulator_disable(info->micvdd);
-		pm_runtime_mark_last_busy(info->dev);
-		pm_runtime_put_autosuspend(info->dev);
-	}
-}
-
-static struct {
-	unsigned int threshold;
-	unsigned int factor_a;
-	unsigned int factor_b;
-} arizona_hpdet_b_ranges[] = {
-	{ 100,  5528,   362464 },
-	{ 169, 11084,  6186851 },
-	{ 169, 11065, 65460395 },
-};
-
-#define ARIZONA_HPDET_B_RANGE_MAX 0x3fb
-
-static struct {
-	int min;
-	int max;
-} arizona_hpdet_c_ranges[] = {
-	{ 0,       30 },
-	{ 8,      100 },
-	{ 100,   1000 },
-	{ 1000, 10000 },
-};
-
-static int arizona_hpdet_read(struct arizona_extcon_info *info)
-{
-	struct arizona *arizona = info->arizona;
-	unsigned int val, range;
-	int ret;
-
-	ret = regmap_read(arizona->regmap, ARIZONA_HEADPHONE_DETECT_2, &val);
-	if (ret != 0) {
-		dev_err(arizona->dev, "Failed to read HPDET status: %d\n",
-			ret);
-		return ret;
-	}
-
-	switch (info->hpdet_ip_version) {
-	case 0:
-		if (!(val & ARIZONA_HP_DONE)) {
-			dev_err(arizona->dev, "HPDET did not complete: %x\n",
-				val);
-			return -EAGAIN;
-		}
-
-		val &= ARIZONA_HP_LVL_MASK;
-		break;
-
-	case 1:
-		if (!(val & ARIZONA_HP_DONE_B)) {
-			dev_err(arizona->dev, "HPDET did not complete: %x\n",
-				val);
-			return -EAGAIN;
-		}
-
-		ret = regmap_read(arizona->regmap, ARIZONA_HP_DACVAL, &val);
-		if (ret != 0) {
-			dev_err(arizona->dev, "Failed to read HP value: %d\n",
-				ret);
-			return -EAGAIN;
-		}
-
-		regmap_read(arizona->regmap, ARIZONA_HEADPHONE_DETECT_1,
-			    &range);
-		range = (range & ARIZONA_HP_IMPEDANCE_RANGE_MASK)
-			   >> ARIZONA_HP_IMPEDANCE_RANGE_SHIFT;
-
-		if (range < ARRAY_SIZE(arizona_hpdet_b_ranges) - 1 &&
-		    (val < arizona_hpdet_b_ranges[range].threshold ||
-		     val >= ARIZONA_HPDET_B_RANGE_MAX)) {
-			range++;
-			dev_dbg(arizona->dev, "Moving to HPDET range %d\n",
-				range);
-			regmap_update_bits(arizona->regmap,
-					   ARIZONA_HEADPHONE_DETECT_1,
-					   ARIZONA_HP_IMPEDANCE_RANGE_MASK,
-					   range <<
-					   ARIZONA_HP_IMPEDANCE_RANGE_SHIFT);
-			return -EAGAIN;
-		}
-
-		/* If we go out of range report top of range */
-		if (val < arizona_hpdet_b_ranges[range].threshold ||
-		    val >= ARIZONA_HPDET_B_RANGE_MAX) {
-			dev_dbg(arizona->dev, "Measurement out of range\n");
-			return ARIZONA_HPDET_MAX;
-		}
-
-		dev_dbg(arizona->dev, "HPDET read %d in range %d\n",
-			val, range);
-
-		val = arizona_hpdet_b_ranges[range].factor_b
-			/ ((val * 100) -
-			   arizona_hpdet_b_ranges[range].factor_a);
-		break;
-
-	case 2:
-		if (!(val & ARIZONA_HP_DONE_B)) {
-			dev_err(arizona->dev, "HPDET did not complete: %x\n",
-				val);
-			return -EAGAIN;
-		}
-
-		val &= ARIZONA_HP_LVL_B_MASK;
-		/* Convert to ohms, the value is in 0.5 ohm increments */
-		val /= 2;
-
-		regmap_read(arizona->regmap, ARIZONA_HEADPHONE_DETECT_1,
-			    &range);
-		range = (range & ARIZONA_HP_IMPEDANCE_RANGE_MASK)
-			   >> ARIZONA_HP_IMPEDANCE_RANGE_SHIFT;
-
-		/* Skip up a range, or report? */
-		if (range < ARRAY_SIZE(arizona_hpdet_c_ranges) - 1 &&
-		    (val >= arizona_hpdet_c_ranges[range].max)) {
-			range++;
-			dev_dbg(arizona->dev, "Moving to HPDET range %d-%d\n",
-				arizona_hpdet_c_ranges[range].min,
-				arizona_hpdet_c_ranges[range].max);
-			regmap_update_bits(arizona->regmap,
-					   ARIZONA_HEADPHONE_DETECT_1,
-					   ARIZONA_HP_IMPEDANCE_RANGE_MASK,
-					   range <<
-					   ARIZONA_HP_IMPEDANCE_RANGE_SHIFT);
-			return -EAGAIN;
-		}
-
-		if (range && (val < arizona_hpdet_c_ranges[range].min)) {
-			dev_dbg(arizona->dev, "Reporting range boundary %d\n",
-				arizona_hpdet_c_ranges[range].min);
-			val = arizona_hpdet_c_ranges[range].min;
-		}
-		break;
-
-	default:
-		dev_warn(arizona->dev, "Unknown HPDET IP revision %d\n",
-			 info->hpdet_ip_version);
-		return -EINVAL;
-	}
-
-	dev_dbg(arizona->dev, "HP impedance %d ohms\n", val);
-	return val;
-}
-
-static int arizona_hpdet_do_id(struct arizona_extcon_info *info, int *reading,
-			       bool *mic)
-{
-	struct arizona *arizona = info->arizona;
-	int id_gpio = arizona->pdata.hpdet_id_gpio;
-
-	if (!arizona->pdata.hpdet_acc_id)
-		return 0;
-
-	/*
-	 * If we're using HPDET for accessory identification we need
-	 * to take multiple measurements, step through them in sequence.
-	 */
-	info->hpdet_res[info->num_hpdet_res++] = *reading;
-
-	/* Only check the mic directly if we didn't already ID it */
-	if (id_gpio && info->num_hpdet_res == 1) {
-		dev_dbg(arizona->dev, "Measuring mic\n");
-
-		regmap_update_bits(arizona->regmap,
-				   ARIZONA_ACCESSORY_DETECT_MODE_1,
-				   ARIZONA_ACCDET_MODE_MASK |
-				   ARIZONA_ACCDET_SRC,
-				   ARIZONA_ACCDET_MODE_HPR |
-				   info->micd_modes[0].src);
-
-		gpio_set_value_cansleep(id_gpio, 1);
-
-		regmap_update_bits(arizona->regmap, ARIZONA_HEADPHONE_DETECT_1,
-				   ARIZONA_HP_POLL, ARIZONA_HP_POLL);
-		return -EAGAIN;
-	}
-
-	/* OK, got both.  Now, compare... */
-	dev_dbg(arizona->dev, "HPDET measured %d %d\n",
-		info->hpdet_res[0], info->hpdet_res[1]);
-
-	/* Take the headphone impedance for the main report */
-	*reading = info->hpdet_res[0];
-
-	/* Sometimes we get false readings due to slow insert */
-	if (*reading >= ARIZONA_HPDET_MAX && !info->hpdet_retried) {
-		dev_dbg(arizona->dev, "Retrying high impedance\n");
-		info->num_hpdet_res = 0;
-		info->hpdet_retried = true;
-		arizona_start_hpdet_acc_id(info);
-		pm_runtime_put(info->dev);
-		return -EAGAIN;
-	}
-
-	/*
-	 * If we measure the mic as high impedance
-	 */
-	if (!id_gpio || info->hpdet_res[1] > 50) {
-		dev_dbg(arizona->dev, "Detected mic\n");
-		*mic = true;
-		info->detecting = true;
-	} else {
-		dev_dbg(arizona->dev, "Detected headphone\n");
-	}
-
-	/* Make sure everything is reset back to the real polarity */
-	regmap_update_bits(arizona->regmap, ARIZONA_ACCESSORY_DETECT_MODE_1,
-			   ARIZONA_ACCDET_SRC, info->micd_modes[0].src);
-
-	return 0;
-}
-
-static irqreturn_t arizona_hpdet_irq(int irq, void *data)
-{
-	struct arizona_extcon_info *info = data;
-	struct arizona *arizona = info->arizona;
-	int id_gpio = arizona->pdata.hpdet_id_gpio;
-	unsigned int report = EXTCON_JACK_HEADPHONE;
-	int ret, reading;
-	bool mic = false;
-
-	mutex_lock(&info->lock);
-
-	/* If we got a spurious IRQ for some reason then ignore it */
-	if (!info->hpdet_active) {
-		dev_warn(arizona->dev, "Spurious HPDET IRQ\n");
-		mutex_unlock(&info->lock);
-		return IRQ_NONE;
-	}
-
-	/* If the cable was removed while measuring ignore the result */
-	ret = extcon_get_state(info->edev, EXTCON_MECHANICAL);
-	if (ret < 0) {
-		dev_err(arizona->dev, "Failed to check cable state: %d\n",
-			ret);
-		goto out;
-	} else if (!ret) {
-		dev_dbg(arizona->dev, "Ignoring HPDET for removed cable\n");
-		goto done;
-	}
-
-	ret = arizona_hpdet_read(info);
-	if (ret == -EAGAIN)
-		goto out;
-	else if (ret < 0)
-		goto done;
-	reading = ret;
-
-	/* Reset back to starting range */
-	regmap_update_bits(arizona->regmap,
-			   ARIZONA_HEADPHONE_DETECT_1,
-			   ARIZONA_HP_IMPEDANCE_RANGE_MASK | ARIZONA_HP_POLL,
-			   0);
-
-	ret = arizona_hpdet_do_id(info, &reading, &mic);
-	if (ret == -EAGAIN)
-		goto out;
-	else if (ret < 0)
-		goto done;
-
-	/* Report high impedence cables as line outputs */
-	if (reading >= 5000)
-		report = EXTCON_JACK_LINE_OUT;
-	else
-		report = EXTCON_JACK_HEADPHONE;
-
-	ret = extcon_set_state_sync(info->edev, report, true);
-	if (ret != 0)
-		dev_err(arizona->dev, "Failed to report HP/line: %d\n",
-			ret);
-
-done:
-	/* Reset back to starting range */
-	regmap_update_bits(arizona->regmap,
-			   ARIZONA_HEADPHONE_DETECT_1,
-			   ARIZONA_HP_IMPEDANCE_RANGE_MASK | ARIZONA_HP_POLL,
-			   0);
-
-	arizona_extcon_hp_clamp(info, false);
-
-	if (id_gpio)
-		gpio_set_value_cansleep(id_gpio, 0);
-
-	/* If we have a mic then reenable MICDET */
-	if (mic || info->mic)
-		arizona_start_mic(info);
-
-	if (info->hpdet_active) {
-		pm_runtime_put_autosuspend(info->dev);
-		info->hpdet_active = false;
-	}
-
-	info->hpdet_done = true;
-
-out:
-	mutex_unlock(&info->lock);
-
-	return IRQ_HANDLED;
-}
-
-static void arizona_identify_headphone(struct arizona_extcon_info *info)
-{
-	struct arizona *arizona = info->arizona;
-	int ret;
-
-	if (info->hpdet_done)
-		return;
-
-	dev_dbg(arizona->dev, "Starting HPDET\n");
-
-	/* Make sure we keep the device enabled during the measurement */
-	pm_runtime_get(info->dev);
-
-	info->hpdet_active = true;
-
-	arizona_stop_mic(info);
-
-	arizona_extcon_hp_clamp(info, true);
-
-	ret = regmap_update_bits(arizona->regmap,
-				 ARIZONA_ACCESSORY_DETECT_MODE_1,
-				 ARIZONA_ACCDET_MODE_MASK,
-				 arizona->pdata.hpdet_channel);
-	if (ret != 0) {
-		dev_err(arizona->dev, "Failed to set HPDET mode: %d\n", ret);
-		goto err;
-	}
-
-	ret = regmap_update_bits(arizona->regmap, ARIZONA_HEADPHONE_DETECT_1,
-				 ARIZONA_HP_POLL, ARIZONA_HP_POLL);
-	if (ret != 0) {
-		dev_err(arizona->dev, "Can't start HPDETL measurement: %d\n",
-			ret);
-		goto err;
-	}
-
-	return;
-
-err:
-	arizona_extcon_hp_clamp(info, false);
-	pm_runtime_put_autosuspend(info->dev);
-
-	/* Just report headphone */
-	ret = extcon_set_state_sync(info->edev, EXTCON_JACK_HEADPHONE, true);
-	if (ret != 0)
-		dev_err(arizona->dev, "Failed to report headphone: %d\n", ret);
-
-	if (info->mic)
-		arizona_start_mic(info);
-
-	info->hpdet_active = false;
-}
-
-static void arizona_start_hpdet_acc_id(struct arizona_extcon_info *info)
-{
-	struct arizona *arizona = info->arizona;
-	int hp_reading = 32;
-	bool mic;
-	int ret;
-
-	dev_dbg(arizona->dev, "Starting identification via HPDET\n");
-
-	/* Make sure we keep the device enabled during the measurement */
-	pm_runtime_get_sync(info->dev);
-
-	info->hpdet_active = true;
-
-	arizona_extcon_hp_clamp(info, true);
-
-	ret = regmap_update_bits(arizona->regmap,
-				 ARIZONA_ACCESSORY_DETECT_MODE_1,
-				 ARIZONA_ACCDET_SRC | ARIZONA_ACCDET_MODE_MASK,
-				 info->micd_modes[0].src |
-				 arizona->pdata.hpdet_channel);
-	if (ret != 0) {
-		dev_err(arizona->dev, "Failed to set HPDET mode: %d\n", ret);
-		goto err;
-	}
-
-	if (arizona->pdata.hpdet_acc_id_line) {
-		ret = regmap_update_bits(arizona->regmap,
-					 ARIZONA_HEADPHONE_DETECT_1,
-					 ARIZONA_HP_POLL, ARIZONA_HP_POLL);
-		if (ret != 0) {
-			dev_err(arizona->dev,
-				"Can't start HPDETL measurement: %d\n",
-				ret);
-			goto err;
-		}
-	} else {
-		arizona_hpdet_do_id(info, &hp_reading, &mic);
-	}
-
-	return;
-
-err:
-	/* Just report headphone */
-	ret = extcon_set_state_sync(info->edev, EXTCON_JACK_HEADPHONE, true);
-	if (ret != 0)
-		dev_err(arizona->dev, "Failed to report headphone: %d\n", ret);
-
-	info->hpdet_active = false;
-}
-
-static void arizona_micd_timeout_work(struct work_struct *work)
-{
-	struct arizona_extcon_info *info = container_of(work,
-						struct arizona_extcon_info,
-						micd_timeout_work.work);
-
-	mutex_lock(&info->lock);
-
-	dev_dbg(info->arizona->dev, "MICD timed out, reporting HP\n");
-
-	info->detecting = false;
-
-	arizona_identify_headphone(info);
-
-	mutex_unlock(&info->lock);
-}
-
-static int arizona_micd_adc_read(struct arizona_extcon_info *info)
-{
-	struct arizona *arizona = info->arizona;
-	unsigned int val;
-	int ret;
-
-	/* Must disable MICD before we read the ADCVAL */
-	regmap_update_bits(arizona->regmap, ARIZONA_MIC_DETECT_1,
-			   ARIZONA_MICD_ENA, 0);
-
-	ret = regmap_read(arizona->regmap, ARIZONA_MIC_DETECT_4, &val);
-	if (ret != 0) {
-		dev_err(arizona->dev,
-			"Failed to read MICDET_ADCVAL: %d\n", ret);
-		return ret;
-	}
-
-	dev_dbg(arizona->dev, "MICDET_ADCVAL: %x\n", val);
-
-	val &= ARIZONA_MICDET_ADCVAL_MASK;
-	if (val < ARRAY_SIZE(arizona_micd_levels))
-		val = arizona_micd_levels[val];
-	else
-		val = INT_MAX;
-
-	if (val <= QUICK_HEADPHONE_MAX_OHM)
-		val = ARIZONA_MICD_STS | ARIZONA_MICD_LVL_0;
-	else if (val <= MICROPHONE_MIN_OHM)
-		val = ARIZONA_MICD_STS | ARIZONA_MICD_LVL_1;
-	else if (val <= MICROPHONE_MAX_OHM)
-		val = ARIZONA_MICD_STS | ARIZONA_MICD_LVL_8;
-	else
-		val = ARIZONA_MICD_LVL_8;
-
-	return val;
-}
-
-static int arizona_micd_read(struct arizona_extcon_info *info)
-{
-	struct arizona *arizona = info->arizona;
-	unsigned int val = 0;
-	int ret, i;
-
-	for (i = 0; i < 10 && !(val & MICD_LVL_0_TO_8); i++) {
-		ret = regmap_read(arizona->regmap, ARIZONA_MIC_DETECT_3, &val);
-		if (ret != 0) {
-			dev_err(arizona->dev,
-				"Failed to read MICDET: %d\n", ret);
-			return ret;
-		}
-
-		dev_dbg(arizona->dev, "MICDET: %x\n", val);
-
-		if (!(val & ARIZONA_MICD_VALID)) {
-			dev_warn(arizona->dev,
-				 "Microphone detection state invalid\n");
-			return -EINVAL;
-		}
-	}
-
-	if (i == 10 && !(val & MICD_LVL_0_TO_8)) {
-		dev_err(arizona->dev, "Failed to get valid MICDET value\n");
-		return -EINVAL;
-	}
-
-	return val;
-}
-
-static int arizona_micdet_reading(void *priv)
-{
-	struct arizona_extcon_info *info = priv;
-	struct arizona *arizona = info->arizona;
-	int ret, val;
-
-	if (info->detecting && arizona->pdata.micd_software_compare)
-		ret = arizona_micd_adc_read(info);
-	else
-		ret = arizona_micd_read(info);
-	if (ret < 0)
-		return ret;
-
-	val = ret;
-
-	/* Due to jack detect this should never happen */
-	if (!(val & ARIZONA_MICD_STS)) {
-		dev_warn(arizona->dev, "Detected open circuit\n");
-		info->mic = false;
-		info->detecting = false;
-		arizona_identify_headphone(info);
-		return 0;
-	}
-
-	/* If we got a high impedence we should have a headset, report it. */
-	if (val & ARIZONA_MICD_LVL_8) {
-		info->mic = true;
-		info->detecting = false;
-
-		arizona_identify_headphone(info);
-
-		ret = extcon_set_state_sync(info->edev,
-					      EXTCON_JACK_MICROPHONE, true);
-		if (ret != 0)
-			dev_err(arizona->dev, "Headset report failed: %d\n",
-				ret);
-
-		/* Don't need to regulate for button detection */
-		ret = regulator_allow_bypass(info->micvdd, true);
-		if (ret != 0) {
-			dev_err(arizona->dev, "Failed to bypass MICVDD: %d\n",
-				ret);
-		}
-
-		return 0;
-	}
-
-	/* If we detected a lower impedence during initial startup
-	 * then we probably have the wrong polarity, flip it.  Don't
-	 * do this for the lowest impedences to speed up detection of
-	 * plain headphones.  If both polarities report a low
-	 * impedence then give up and report headphones.
-	 */
-	if (val & MICD_LVL_1_TO_7) {
-		if (info->jack_flips >= info->micd_num_modes * 10) {
-			dev_dbg(arizona->dev, "Detected HP/line\n");
-
-			info->detecting = false;
-
-			arizona_identify_headphone(info);
-		} else {
-			info->micd_mode++;
-			if (info->micd_mode == info->micd_num_modes)
-				info->micd_mode = 0;
-			arizona_extcon_set_mode(info, info->micd_mode);
-
-			info->jack_flips++;
-
-			if (arizona->pdata.micd_software_compare)
-				regmap_update_bits(arizona->regmap,
-						   ARIZONA_MIC_DETECT_1,
-						   ARIZONA_MICD_ENA,
-						   ARIZONA_MICD_ENA);
-
-			queue_delayed_work(system_power_efficient_wq,
-					   &info->micd_timeout_work,
-					   msecs_to_jiffies(arizona->pdata.micd_timeout));
-		}
-
-		return 0;
-	}
-
-	/*
-	 * If we're still detecting and we detect a short then we've
-	 * got a headphone.
-	 */
-	dev_dbg(arizona->dev, "Headphone detected\n");
-	info->detecting = false;
-
-	arizona_identify_headphone(info);
-
-	return 0;
-}
-
-static int arizona_button_reading(void *priv)
-{
-	struct arizona_extcon_info *info = priv;
-	struct arizona *arizona = info->arizona;
-	int val, key, lvl, i;
-
-	val = arizona_micd_read(info);
-	if (val < 0)
-		return val;
-
-	/*
-	 * If we're still detecting and we detect a short then we've
-	 * got a headphone.  Otherwise it's a button press.
-	 */
-	if (val & MICD_LVL_0_TO_7) {
-		if (info->mic) {
-			dev_dbg(arizona->dev, "Mic button detected\n");
-
-			lvl = val & ARIZONA_MICD_LVL_MASK;
-			lvl >>= ARIZONA_MICD_LVL_SHIFT;
-
-			for (i = 0; i < info->num_micd_ranges; i++)
-				input_report_key(info->input,
-						 info->micd_ranges[i].key, 0);
-
-			if (lvl && ffs(lvl) - 1 < info->num_micd_ranges) {
-				key = info->micd_ranges[ffs(lvl) - 1].key;
-				input_report_key(info->input, key, 1);
-				input_sync(info->input);
-			} else {
-				dev_err(arizona->dev, "Button out of range\n");
-			}
-		} else {
-			dev_warn(arizona->dev, "Button with no mic: %x\n",
-				 val);
-		}
-	} else {
-		dev_dbg(arizona->dev, "Mic button released\n");
-		for (i = 0; i < info->num_micd_ranges; i++)
-			input_report_key(info->input,
-					 info->micd_ranges[i].key, 0);
-		input_sync(info->input);
-		arizona_extcon_pulse_micbias(info);
-	}
-
-	return 0;
-}
-
-static void arizona_micd_detect(struct work_struct *work)
-{
-	struct arizona_extcon_info *info = container_of(work,
-						struct arizona_extcon_info,
-						micd_detect_work.work);
-	struct arizona *arizona = info->arizona;
-	int ret;
-
-	cancel_delayed_work_sync(&info->micd_timeout_work);
-
-	mutex_lock(&info->lock);
-
-	/* If the cable was removed while measuring ignore the result */
-	ret = extcon_get_state(info->edev, EXTCON_MECHANICAL);
-	if (ret < 0) {
-		dev_err(arizona->dev, "Failed to check cable state: %d\n",
-				ret);
-		mutex_unlock(&info->lock);
-		return;
-	} else if (!ret) {
-		dev_dbg(arizona->dev, "Ignoring MICDET for removed cable\n");
-		mutex_unlock(&info->lock);
-		return;
-	}
-
-	if (info->detecting)
-		arizona_micdet_reading(info);
-	else
-		arizona_button_reading(info);
-
-	pm_runtime_mark_last_busy(info->dev);
-	mutex_unlock(&info->lock);
-}
-
-static irqreturn_t arizona_micdet(int irq, void *data)
-{
-	struct arizona_extcon_info *info = data;
-	struct arizona *arizona = info->arizona;
-	int debounce = arizona->pdata.micd_detect_debounce;
-
-	cancel_delayed_work_sync(&info->micd_detect_work);
-	cancel_delayed_work_sync(&info->micd_timeout_work);
-
-	mutex_lock(&info->lock);
-	if (!info->detecting)
-		debounce = 0;
-	mutex_unlock(&info->lock);
-
-	if (debounce)
-		queue_delayed_work(system_power_efficient_wq,
-				   &info->micd_detect_work,
-				   msecs_to_jiffies(debounce));
-	else
-		arizona_micd_detect(&info->micd_detect_work.work);
-
-	return IRQ_HANDLED;
-}
-
-static void arizona_hpdet_work(struct work_struct *work)
-{
-	struct arizona_extcon_info *info = container_of(work,
-						struct arizona_extcon_info,
-						hpdet_work.work);
-
-	mutex_lock(&info->lock);
-	arizona_start_hpdet_acc_id(info);
-	mutex_unlock(&info->lock);
-}
-
-static int arizona_hpdet_wait(struct arizona_extcon_info *info)
-{
-	struct arizona *arizona = info->arizona;
-	unsigned int val;
-	int i, ret;
-
-	for (i = 0; i < ARIZONA_HPDET_WAIT_COUNT; i++) {
-		ret = regmap_read(arizona->regmap, ARIZONA_HEADPHONE_DETECT_2,
-				&val);
-		if (ret) {
-			dev_err(arizona->dev,
-				"Failed to read HPDET state: %d\n", ret);
-			return ret;
-		}
-
-		switch (info->hpdet_ip_version) {
-		case 0:
-			if (val & ARIZONA_HP_DONE)
-				return 0;
-			break;
-		default:
-			if (val & ARIZONA_HP_DONE_B)
-				return 0;
-			break;
-		}
-
-		msleep(ARIZONA_HPDET_WAIT_DELAY_MS);
-	}
-
-	dev_warn(arizona->dev, "HPDET did not appear to complete\n");
-
-	return -ETIMEDOUT;
-}
-
-static irqreturn_t arizona_jackdet(int irq, void *data)
-{
-	struct arizona_extcon_info *info = data;
-	struct arizona *arizona = info->arizona;
-	unsigned int val, present, mask;
-	bool cancelled_hp, cancelled_mic;
-	int ret, i;
-
-	cancelled_hp = cancel_delayed_work_sync(&info->hpdet_work);
-	cancelled_mic = cancel_delayed_work_sync(&info->micd_timeout_work);
-
-	pm_runtime_get_sync(info->dev);
-
-	mutex_lock(&info->lock);
-
-	if (info->micd_clamp) {
-		mask = ARIZONA_MICD_CLAMP_STS;
-		present = 0;
-	} else {
-		mask = ARIZONA_JD1_STS;
-		if (arizona->pdata.jd_invert)
-			present = 0;
-		else
-			present = ARIZONA_JD1_STS;
-	}
-
-	ret = regmap_read(arizona->regmap, ARIZONA_AOD_IRQ_RAW_STATUS, &val);
-	if (ret != 0) {
-		dev_err(arizona->dev, "Failed to read jackdet status: %d\n",
-			ret);
-		mutex_unlock(&info->lock);
-		pm_runtime_put_autosuspend(info->dev);
-		return IRQ_NONE;
-	}
-
-	val &= mask;
-	if (val == info->last_jackdet) {
-		dev_dbg(arizona->dev, "Suppressing duplicate JACKDET\n");
-		if (cancelled_hp)
-			queue_delayed_work(system_power_efficient_wq,
-					   &info->hpdet_work,
-					   msecs_to_jiffies(HPDET_DEBOUNCE));
-
-		if (cancelled_mic) {
-			int micd_timeout = arizona->pdata.micd_timeout;
-
-			queue_delayed_work(system_power_efficient_wq,
-					   &info->micd_timeout_work,
-					   msecs_to_jiffies(micd_timeout));
-		}
-
-		goto out;
-	}
-	info->last_jackdet = val;
-
-	if (info->last_jackdet == present) {
-		dev_dbg(arizona->dev, "Detected jack\n");
-		ret = extcon_set_state_sync(info->edev,
-					      EXTCON_MECHANICAL, true);
-
-		if (ret != 0)
-			dev_err(arizona->dev, "Mechanical report failed: %d\n",
-				ret);
-
-		info->detecting = true;
-		info->mic = false;
-		info->jack_flips = 0;
-
-		if (!arizona->pdata.hpdet_acc_id) {
-			arizona_start_mic(info);
-		} else {
-			queue_delayed_work(system_power_efficient_wq,
-					   &info->hpdet_work,
-					   msecs_to_jiffies(HPDET_DEBOUNCE));
-		}
-
-		if (info->micd_clamp || !arizona->pdata.jd_invert)
-			regmap_update_bits(arizona->regmap,
-					   ARIZONA_JACK_DETECT_DEBOUNCE,
-					   ARIZONA_MICD_CLAMP_DB |
-					   ARIZONA_JD1_DB, 0);
-	} else {
-		dev_dbg(arizona->dev, "Detected jack removal\n");
-
-		arizona_stop_mic(info);
-
-		info->num_hpdet_res = 0;
-		for (i = 0; i < ARRAY_SIZE(info->hpdet_res); i++)
-			info->hpdet_res[i] = 0;
-		info->mic = false;
-		info->hpdet_done = false;
-		info->hpdet_retried = false;
-
-		for (i = 0; i < info->num_micd_ranges; i++)
-			input_report_key(info->input,
-					 info->micd_ranges[i].key, 0);
-		input_sync(info->input);
-
-		for (i = 0; i < ARRAY_SIZE(arizona_cable) - 1; i++) {
-			ret = extcon_set_state_sync(info->edev,
-					arizona_cable[i], false);
-			if (ret != 0)
-				dev_err(arizona->dev,
-					"Removal report failed: %d\n", ret);
-		}
-
-		/*
-		 * If the jack was removed during a headphone detection we
-		 * need to wait for the headphone detection to finish, as
-		 * it can not be aborted. We don't want to be able to start
-		 * a new headphone detection from a fresh insert until this
-		 * one is finished.
-		 */
-		arizona_hpdet_wait(info);
-
-		regmap_update_bits(arizona->regmap,
-				   ARIZONA_JACK_DETECT_DEBOUNCE,
-				   ARIZONA_MICD_CLAMP_DB | ARIZONA_JD1_DB,
-				   ARIZONA_MICD_CLAMP_DB | ARIZONA_JD1_DB);
-	}
-
-out:
-	/* Clear trig_sts to make sure DCVDD is not forced up */
-	regmap_write(arizona->regmap, ARIZONA_AOD_WKUP_AND_TRIG,
-		     ARIZONA_MICD_CLAMP_FALL_TRIG_STS |
-		     ARIZONA_MICD_CLAMP_RISE_TRIG_STS |
-		     ARIZONA_JD1_FALL_TRIG_STS |
-		     ARIZONA_JD1_RISE_TRIG_STS);
-
-	mutex_unlock(&info->lock);
-
-	pm_runtime_mark_last_busy(info->dev);
-	pm_runtime_put_autosuspend(info->dev);
-
-	return IRQ_HANDLED;
-}
-
-/* Map a level onto a slot in the register bank */
-static void arizona_micd_set_level(struct arizona *arizona, int index,
-				   unsigned int level)
-{
-	int reg;
-	unsigned int mask;
-
-	reg = ARIZONA_MIC_DETECT_LEVEL_4 - (index / 2);
-
-	if (!(index % 2)) {
-		mask = 0x3f00;
-		level <<= 8;
-	} else {
-		mask = 0x3f;
-	}
-
-	/* Program the level itself */
-	regmap_update_bits(arizona->regmap, reg, mask, level);
-}
-
-static int arizona_extcon_get_micd_configs(struct device *dev,
-					   struct arizona *arizona)
-{
-	const char * const prop = "wlf,micd-configs";
-	const int entries_per_config = 3;
-	struct arizona_micd_config *micd_configs;
-	int nconfs, ret;
-	int i, j;
-	u32 *vals;
-
-	nconfs = device_property_count_u32(arizona->dev, prop);
-	if (nconfs <= 0)
-		return 0;
-
-	vals = kcalloc(nconfs, sizeof(u32), GFP_KERNEL);
-	if (!vals)
-		return -ENOMEM;
-
-	ret = device_property_read_u32_array(arizona->dev, prop, vals, nconfs);
-	if (ret < 0)
-		goto out;
-
-	nconfs /= entries_per_config;
-	micd_configs = devm_kcalloc(dev, nconfs, sizeof(*micd_configs),
-				    GFP_KERNEL);
-	if (!micd_configs) {
-		ret = -ENOMEM;
-		goto out;
-	}
-
-	for (i = 0, j = 0; i < nconfs; ++i) {
-		micd_configs[i].src = vals[j++] ? ARIZONA_ACCDET_SRC : 0;
-		micd_configs[i].bias = vals[j++];
-		micd_configs[i].gpio = vals[j++];
-	}
-
-	arizona->pdata.micd_configs = micd_configs;
-	arizona->pdata.num_micd_configs = nconfs;
-
-out:
-	kfree(vals);
-	return ret;
-}
-
-static int arizona_extcon_device_get_pdata(struct device *dev,
-					   struct arizona *arizona)
-{
-	struct arizona_pdata *pdata = &arizona->pdata;
-	unsigned int val = ARIZONA_ACCDET_MODE_HPL;
-	int ret;
-
-	device_property_read_u32(arizona->dev, "wlf,hpdet-channel", &val);
-	switch (val) {
-	case ARIZONA_ACCDET_MODE_HPL:
-	case ARIZONA_ACCDET_MODE_HPR:
-		pdata->hpdet_channel = val;
-		break;
-	default:
-		dev_err(arizona->dev,
-			"Wrong wlf,hpdet-channel DT value %d\n", val);
-		pdata->hpdet_channel = ARIZONA_ACCDET_MODE_HPL;
-	}
-
-	device_property_read_u32(arizona->dev, "wlf,micd-detect-debounce",
-				 &pdata->micd_detect_debounce);
-
-	device_property_read_u32(arizona->dev, "wlf,micd-bias-start-time",
-				 &pdata->micd_bias_start_time);
-
-	device_property_read_u32(arizona->dev, "wlf,micd-rate",
-				 &pdata->micd_rate);
-
-	device_property_read_u32(arizona->dev, "wlf,micd-dbtime",
-				 &pdata->micd_dbtime);
-
-	device_property_read_u32(arizona->dev, "wlf,micd-timeout-ms",
-				 &pdata->micd_timeout);
-
-	pdata->micd_force_micbias = device_property_read_bool(arizona->dev,
-						"wlf,micd-force-micbias");
-
-	pdata->micd_software_compare = device_property_read_bool(arizona->dev,
-						"wlf,micd-software-compare");
-
-	pdata->jd_invert = device_property_read_bool(arizona->dev,
-						     "wlf,jd-invert");
-
-	device_property_read_u32(arizona->dev, "wlf,gpsw", &pdata->gpsw);
-
-	pdata->jd_gpio5 = device_property_read_bool(arizona->dev,
-						    "wlf,use-jd2");
-	pdata->jd_gpio5_nopull = device_property_read_bool(arizona->dev,
-						"wlf,use-jd2-nopull");
-
-	ret = arizona_extcon_get_micd_configs(dev, arizona);
-	if (ret < 0)
-		dev_err(arizona->dev, "Failed to read micd configs: %d\n", ret);
-
-	return 0;
-}
-
-static int arizona_extcon_probe(struct platform_device *pdev)
-{
-	struct arizona *arizona = dev_get_drvdata(pdev->dev.parent);
-	struct arizona_pdata *pdata = &arizona->pdata;
-	struct arizona_extcon_info *info;
-	unsigned int val;
-	unsigned int clamp_mode;
-	int jack_irq_fall, jack_irq_rise;
-	int ret, mode, i, j;
-
-	if (!arizona->dapm || !arizona->dapm->card)
-		return -EPROBE_DEFER;
-
-	info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL);
-	if (!info)
-		return -ENOMEM;
-
-	if (!dev_get_platdata(arizona->dev))
-		arizona_extcon_device_get_pdata(&pdev->dev, arizona);
-
-	info->micvdd = devm_regulator_get(&pdev->dev, "MICVDD");
-	if (IS_ERR(info->micvdd)) {
-		ret = PTR_ERR(info->micvdd);
-		dev_err(arizona->dev, "Failed to get MICVDD: %d\n", ret);
-		return ret;
-	}
-
-	mutex_init(&info->lock);
-	info->arizona = arizona;
-	info->dev = &pdev->dev;
-	info->last_jackdet = ~(ARIZONA_MICD_CLAMP_STS | ARIZONA_JD1_STS);
-	INIT_DELAYED_WORK(&info->hpdet_work, arizona_hpdet_work);
-	INIT_DELAYED_WORK(&info->micd_detect_work, arizona_micd_detect);
-	INIT_DELAYED_WORK(&info->micd_timeout_work, arizona_micd_timeout_work);
-	platform_set_drvdata(pdev, info);
-
-	switch (arizona->type) {
-	case WM5102:
-		switch (arizona->rev) {
-		case 0:
-			info->micd_reva = true;
-			break;
-		default:
-			info->micd_clamp = true;
-			info->hpdet_ip_version = 1;
-			break;
-		}
-		break;
-	case WM5110:
-	case WM8280:
-		switch (arizona->rev) {
-		case 0 ... 2:
-			break;
-		default:
-			info->micd_clamp = true;
-			info->hpdet_ip_version = 2;
-			break;
-		}
-		break;
-	case WM8998:
-	case WM1814:
-		info->micd_clamp = true;
-		info->hpdet_ip_version = 2;
-		break;
-	default:
-		break;
-	}
-
-	info->edev = devm_extcon_dev_allocate(&pdev->dev, arizona_cable);
-	if (IS_ERR(info->edev)) {
-		dev_err(&pdev->dev, "failed to allocate extcon device\n");
-		return -ENOMEM;
-	}
-
-	ret = devm_extcon_dev_register(&pdev->dev, info->edev);
-	if (ret < 0) {
-		dev_err(arizona->dev, "extcon_dev_register() failed: %d\n",
-			ret);
-		return ret;
-	}
-
-	info->input = devm_input_allocate_device(&pdev->dev);
-	if (!info->input) {
-		dev_err(arizona->dev, "Can't allocate input dev\n");
-		ret = -ENOMEM;
-		return ret;
-	}
-
-	info->input->name = "Headset";
-	info->input->phys = "arizona/extcon";
-
-	if (!pdata->micd_timeout)
-		pdata->micd_timeout = DEFAULT_MICD_TIMEOUT;
-
-	if (pdata->num_micd_configs) {
-		info->micd_modes = pdata->micd_configs;
-		info->micd_num_modes = pdata->num_micd_configs;
-	} else {
-		info->micd_modes = micd_default_modes;
-		info->micd_num_modes = ARRAY_SIZE(micd_default_modes);
-	}
-
-	if (arizona->pdata.gpsw > 0)
-		regmap_update_bits(arizona->regmap, ARIZONA_GP_SWITCH_1,
-				ARIZONA_SW1_MODE_MASK, arizona->pdata.gpsw);
-
-	if (pdata->micd_pol_gpio > 0) {
-		if (info->micd_modes[0].gpio)
-			mode = GPIOF_OUT_INIT_HIGH;
-		else
-			mode = GPIOF_OUT_INIT_LOW;
-
-		ret = devm_gpio_request_one(&pdev->dev, pdata->micd_pol_gpio,
-					    mode, "MICD polarity");
-		if (ret != 0) {
-			dev_err(arizona->dev, "Failed to request GPIO%d: %d\n",
-				pdata->micd_pol_gpio, ret);
-			return ret;
-		}
-
-		info->micd_pol_gpio = gpio_to_desc(pdata->micd_pol_gpio);
-	} else {
-		if (info->micd_modes[0].gpio)
-			mode = GPIOD_OUT_HIGH;
-		else
-			mode = GPIOD_OUT_LOW;
-
-		/* We can't use devm here because we need to do the get
-		 * against the MFD device, as that is where the of_node
-		 * will reside, but if we devm against that the GPIO
-		 * will not be freed if the extcon driver is unloaded.
-		 */
-		info->micd_pol_gpio = gpiod_get_optional(arizona->dev,
-							 "wlf,micd-pol",
-							 GPIOD_OUT_LOW);
-		if (IS_ERR(info->micd_pol_gpio)) {
-			ret = PTR_ERR(info->micd_pol_gpio);
-			dev_err(arizona->dev,
-				"Failed to get microphone polarity GPIO: %d\n",
-				ret);
-			return ret;
-		}
-	}
-
-	if (arizona->pdata.hpdet_id_gpio > 0) {
-		ret = devm_gpio_request_one(&pdev->dev,
-					    arizona->pdata.hpdet_id_gpio,
-					    GPIOF_OUT_INIT_LOW,
-					    "HPDET");
-		if (ret != 0) {
-			dev_err(arizona->dev, "Failed to request GPIO%d: %d\n",
-				arizona->pdata.hpdet_id_gpio, ret);
-			goto err_gpio;
-		}
-	}
-
-	if (arizona->pdata.micd_bias_start_time)
-		regmap_update_bits(arizona->regmap, ARIZONA_MIC_DETECT_1,
-				   ARIZONA_MICD_BIAS_STARTTIME_MASK,
-				   arizona->pdata.micd_bias_start_time
-				   << ARIZONA_MICD_BIAS_STARTTIME_SHIFT);
-
-	if (arizona->pdata.micd_rate)
-		regmap_update_bits(arizona->regmap, ARIZONA_MIC_DETECT_1,
-				   ARIZONA_MICD_RATE_MASK,
-				   arizona->pdata.micd_rate
-				   << ARIZONA_MICD_RATE_SHIFT);
-
-	switch (arizona->pdata.micd_dbtime) {
-	case MICD_DBTIME_FOUR_READINGS:
-		regmap_update_bits(arizona->regmap, ARIZONA_MIC_DETECT_1,
-				   ARIZONA_MICD_DBTIME_MASK,
-				   ARIZONA_MICD_DBTIME);
-		break;
-	case MICD_DBTIME_TWO_READINGS:
-		regmap_update_bits(arizona->regmap, ARIZONA_MIC_DETECT_1,
-				   ARIZONA_MICD_DBTIME_MASK, 0);
-		break;
-	default:
-		break;
-	}
-
-	BUILD_BUG_ON(ARRAY_SIZE(arizona_micd_levels) <
-		     ARIZONA_NUM_MICD_BUTTON_LEVELS);
-
-	if (arizona->pdata.num_micd_ranges) {
-		info->micd_ranges = pdata->micd_ranges;
-		info->num_micd_ranges = pdata->num_micd_ranges;
-	} else {
-		info->micd_ranges = micd_default_ranges;
-		info->num_micd_ranges = ARRAY_SIZE(micd_default_ranges);
-	}
-
-	if (arizona->pdata.num_micd_ranges > ARIZONA_MAX_MICD_RANGE) {
-		dev_err(arizona->dev, "Too many MICD ranges: %d\n",
-			arizona->pdata.num_micd_ranges);
-	}
-
-	if (info->num_micd_ranges > 1) {
-		for (i = 1; i < info->num_micd_ranges; i++) {
-			if (info->micd_ranges[i - 1].max >
-			    info->micd_ranges[i].max) {
-				dev_err(arizona->dev,
-					"MICD ranges must be sorted\n");
-				ret = -EINVAL;
-				goto err_gpio;
-			}
-		}
-	}
-
-	/* Disable all buttons by default */
-	regmap_update_bits(arizona->regmap, ARIZONA_MIC_DETECT_2,
-			   ARIZONA_MICD_LVL_SEL_MASK, 0x81);
-
-	/* Set up all the buttons the user specified */
-	for (i = 0; i < info->num_micd_ranges; i++) {
-		for (j = 0; j < ARIZONA_NUM_MICD_BUTTON_LEVELS; j++)
-			if (arizona_micd_levels[j] >= info->micd_ranges[i].max)
-				break;
-
-		if (j == ARIZONA_NUM_MICD_BUTTON_LEVELS) {
-			dev_err(arizona->dev, "Unsupported MICD level %d\n",
-				info->micd_ranges[i].max);
-			ret = -EINVAL;
-			goto err_gpio;
-		}
-
-		dev_dbg(arizona->dev, "%d ohms for MICD threshold %d\n",
-			arizona_micd_levels[j], i);
-
-		arizona_micd_set_level(arizona, i, j);
-		input_set_capability(info->input, EV_KEY,
-				     info->micd_ranges[i].key);
-
-		/* Enable reporting of that range */
-		regmap_update_bits(arizona->regmap, ARIZONA_MIC_DETECT_2,
-				   1 << i, 1 << i);
-	}
-
-	/* Set all the remaining keys to a maximum */
-	for (; i < ARIZONA_MAX_MICD_RANGE; i++)
-		arizona_micd_set_level(arizona, i, 0x3f);
-
-	/*
-	 * If we have a clamp use it, activating in conjunction with
-	 * GPIO5 if that is connected for jack detect operation.
-	 */
-	if (info->micd_clamp) {
-		if (arizona->pdata.jd_gpio5) {
-			/* Put the GPIO into input mode with optional pull */
-			val = 0xc101;
-			if (arizona->pdata.jd_gpio5_nopull)
-				val &= ~ARIZONA_GPN_PU;
-
-			regmap_write(arizona->regmap, ARIZONA_GPIO5_CTRL,
-				     val);
-
-			if (arizona->pdata.jd_invert)
-				clamp_mode = ARIZONA_MICD_CLAMP_MODE_JDH_GP5H;
-			else
-				clamp_mode = ARIZONA_MICD_CLAMP_MODE_JDL_GP5H;
-		} else {
-			if (arizona->pdata.jd_invert)
-				clamp_mode = ARIZONA_MICD_CLAMP_MODE_JDH;
-			else
-				clamp_mode = ARIZONA_MICD_CLAMP_MODE_JDL;
-		}
-
-		regmap_update_bits(arizona->regmap,
-				   ARIZONA_MICD_CLAMP_CONTROL,
-				   ARIZONA_MICD_CLAMP_MODE_MASK, clamp_mode);
-
-		regmap_update_bits(arizona->regmap,
-				   ARIZONA_JACK_DETECT_DEBOUNCE,
-				   ARIZONA_MICD_CLAMP_DB,
-				   ARIZONA_MICD_CLAMP_DB);
-	}
-
-	arizona_extcon_set_mode(info, 0);
-
-	pm_runtime_enable(&pdev->dev);
-	pm_runtime_idle(&pdev->dev);
-	pm_runtime_get_sync(&pdev->dev);
-
-	if (info->micd_clamp) {
-		jack_irq_rise = ARIZONA_IRQ_MICD_CLAMP_RISE;
-		jack_irq_fall = ARIZONA_IRQ_MICD_CLAMP_FALL;
-	} else {
-		jack_irq_rise = ARIZONA_IRQ_JD_RISE;
-		jack_irq_fall = ARIZONA_IRQ_JD_FALL;
-	}
-
-	ret = arizona_request_irq(arizona, jack_irq_rise,
-				  "JACKDET rise", arizona_jackdet, info);
-	if (ret != 0) {
-		dev_err(&pdev->dev, "Failed to get JACKDET rise IRQ: %d\n",
-			ret);
-		goto err_pm;
-	}
-
-	ret = arizona_set_irq_wake(arizona, jack_irq_rise, 1);
-	if (ret != 0) {
-		dev_err(&pdev->dev, "Failed to set JD rise IRQ wake: %d\n",
-			ret);
-		goto err_rise;
-	}
-
-	ret = arizona_request_irq(arizona, jack_irq_fall,
-				  "JACKDET fall", arizona_jackdet, info);
-	if (ret != 0) {
-		dev_err(&pdev->dev, "Failed to get JD fall IRQ: %d\n", ret);
-		goto err_rise_wake;
-	}
-
-	ret = arizona_set_irq_wake(arizona, jack_irq_fall, 1);
-	if (ret != 0) {
-		dev_err(&pdev->dev, "Failed to set JD fall IRQ wake: %d\n",
-			ret);
-		goto err_fall;
-	}
-
-	ret = arizona_request_irq(arizona, ARIZONA_IRQ_MICDET,
-				  "MICDET", arizona_micdet, info);
-	if (ret != 0) {
-		dev_err(&pdev->dev, "Failed to get MICDET IRQ: %d\n", ret);
-		goto err_fall_wake;
-	}
-
-	ret = arizona_request_irq(arizona, ARIZONA_IRQ_HPDET,
-				  "HPDET", arizona_hpdet_irq, info);
-	if (ret != 0) {
-		dev_err(&pdev->dev, "Failed to get HPDET IRQ: %d\n", ret);
-		goto err_micdet;
-	}
-
-	arizona_clk32k_enable(arizona);
-	regmap_update_bits(arizona->regmap, ARIZONA_JACK_DETECT_DEBOUNCE,
-			   ARIZONA_JD1_DB, ARIZONA_JD1_DB);
-	regmap_update_bits(arizona->regmap, ARIZONA_JACK_DETECT_ANALOGUE,
-			   ARIZONA_JD1_ENA, ARIZONA_JD1_ENA);
-
-	ret = regulator_allow_bypass(info->micvdd, true);
-	if (ret != 0)
-		dev_warn(arizona->dev, "Failed to set MICVDD to bypass: %d\n",
-			 ret);
-
-	ret = input_register_device(info->input);
-	if (ret) {
-		dev_err(&pdev->dev, "Can't register input device: %d\n", ret);
-		goto err_hpdet;
-	}
-
-	pm_runtime_put(&pdev->dev);
-
-	return 0;
-
-err_hpdet:
-	arizona_free_irq(arizona, ARIZONA_IRQ_HPDET, info);
-err_micdet:
-	arizona_free_irq(arizona, ARIZONA_IRQ_MICDET, info);
-err_fall_wake:
-	arizona_set_irq_wake(arizona, jack_irq_fall, 0);
-err_fall:
-	arizona_free_irq(arizona, jack_irq_fall, info);
-err_rise_wake:
-	arizona_set_irq_wake(arizona, jack_irq_rise, 0);
-err_rise:
-	arizona_free_irq(arizona, jack_irq_rise, info);
-err_pm:
-	pm_runtime_put(&pdev->dev);
-	pm_runtime_disable(&pdev->dev);
-err_gpio:
-	gpiod_put(info->micd_pol_gpio);
-	return ret;
-}
-
-static int arizona_extcon_remove(struct platform_device *pdev)
-{
-	struct arizona_extcon_info *info = platform_get_drvdata(pdev);
-	struct arizona *arizona = info->arizona;
-	int jack_irq_rise, jack_irq_fall;
-	bool change;
-	int ret;
-
-	ret = regmap_update_bits_check(arizona->regmap, ARIZONA_MIC_DETECT_1,
-				       ARIZONA_MICD_ENA, 0,
-				       &change);
-	if (ret < 0) {
-		dev_err(&pdev->dev, "Failed to disable micd on remove: %d\n",
-			ret);
-	} else if (change) {
-		regulator_disable(info->micvdd);
-		pm_runtime_put(info->dev);
-	}
-
-	gpiod_put(info->micd_pol_gpio);
-
-	pm_runtime_disable(&pdev->dev);
-
-	regmap_update_bits(arizona->regmap,
-			   ARIZONA_MICD_CLAMP_CONTROL,
-			   ARIZONA_MICD_CLAMP_MODE_MASK, 0);
-
-	if (info->micd_clamp) {
-		jack_irq_rise = ARIZONA_IRQ_MICD_CLAMP_RISE;
-		jack_irq_fall = ARIZONA_IRQ_MICD_CLAMP_FALL;
-	} else {
-		jack_irq_rise = ARIZONA_IRQ_JD_RISE;
-		jack_irq_fall = ARIZONA_IRQ_JD_FALL;
-	}
-
-	arizona_set_irq_wake(arizona, jack_irq_rise, 0);
-	arizona_set_irq_wake(arizona, jack_irq_fall, 0);
-	arizona_free_irq(arizona, ARIZONA_IRQ_HPDET, info);
-	arizona_free_irq(arizona, ARIZONA_IRQ_MICDET, info);
-	arizona_free_irq(arizona, jack_irq_rise, info);
-	arizona_free_irq(arizona, jack_irq_fall, info);
-	cancel_delayed_work_sync(&info->hpdet_work);
-	regmap_update_bits(arizona->regmap, ARIZONA_JACK_DETECT_ANALOGUE,
-			   ARIZONA_JD1_ENA, 0);
-	arizona_clk32k_disable(arizona);
-
-	return 0;
-}
-
-static struct platform_driver arizona_extcon_driver = {
-	.driver		= {
-		.name	= "arizona-extcon",
-	},
-	.probe		= arizona_extcon_probe,
-	.remove		= arizona_extcon_remove,
-};
-
-module_platform_driver(arizona_extcon_driver);
-
-MODULE_DESCRIPTION("Arizona Extcon driver");
-MODULE_AUTHOR("Mark Brown <broonie@xxxxxxxxxxxxxxxxxxxxxxxxxxx>");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:extcon-arizona");
-- 
2.28.0





[Index of Archives]     [ALSA User]     [Linux Audio Users]     [Pulse Audio]     [Kernel Archive]     [Asterisk PBX]     [Photo Sharing]     [Linux Sound]     [Video 4 Linux]     [Gimp]     [Yosemite News]

  Powered by Linux