Ok, the second codec is the HDMI port. For some reason, it is getting assigned to be primary sound device. Try "alsamixer -D hw:1.0" to see if it can control the realtek device. Oddly enough, I used to work at Intel as a contractor, developing audio drivers for their boards. They stopped supporting Linux when my contract ended. I'll see what I can do over the next couple of weeks. Tobin On Thu, 2007-12-27 at 00:33 +0000, De Fuuss wrote: > Hi Tobin, > > Thanks for you quick reply. > > I tried both 3stack-6ch and 3stack-6ch-dig (the card has a spdif out). I found out that when putting on headphones on a separate headphone jack I get some sound with both settings. Hoever, the front out l/r, center/bass sourround back l/r and side sourround l/r port remain silent. > > I set all channels to 80-100% in alsamixer. > > A few more details from my setup: > Shuttle XPC SG33G5M > Intel G33 Express + ICH9DH > > Interestingly, when I run alsamixer, it identifies the Chip as "Generic 1095 ID 1392", in other words in points to codec#1. I thought it should point to codec#0, e.g. RealTek ALC888 > > I have the strong impression that the channels are not truly set by alsamixer as they point to the wrong codec. I'm only a layman in ALSA, and I have no idea how to tell alsamixer to consider codec#0 instead codec#1. > > Do you have any idea on how to crack this nut? > > Below is the output of both codecs: > > Thank you. > > Best regards, > > Patrick > > ____________________ > #cat /proc/asound/cards > > 0 [Intel ]: HDA-Intel - HDA Intel > HDA Intel at 0xfdff8000 irq 22 > > # cat /proc/asound/Intel/codec#0 > Codec: Realtek ALC888 > Address: 0 > Vendor Id: 0x10ec0888 > Subsystem Id: 0x12970888 > Revision Id: 0x100001 > No Modem Function Group found > Default PCM: > rates [0x560]: 44100 48000 96000 192000 > bits [0xe]: 16 20 24 > formats [0x1]: PCM > Default Amp-In caps: N/A > Default Amp-Out caps: N/A > Node 0x02 [Audio Output] wcaps 0x11: Stereo > PCM: > rates [0x560]: 44100 48000 96000 192000 > bits [0xe]: 16 20 24 > formats [0x1]: PCM > Node 0x03 [Audio Output] wcaps 0x11: Stereo > PCM: > rates [0x560]: 44100 48000 96000 192000 > bits [0xe]: 16 20 24 > formats [0x1]: PCM > Node 0x04 [Audio Output] wcaps 0x11: Stereo > PCM: > rates [0x560]: 44100 48000 96000 192000 > bits [0xe]: 16 20 24 > formats [0x1]: PCM > Node 0x05 [Audio Output] wcaps 0x11: Stereo > PCM: > rates [0x560]: 44100 48000 96000 192000 > bits [0xe]: 16 20 24 > formats [0x1]: PCM > Node 0x06 [Audio Output] wcaps 0x211: Stereo Digital > PCM: > rates [0x5e0]: 44100 48000 88200 96000 192000 > bits [0x1e]: 16 20 24 32 > formats [0x1]: PCM > Node 0x07 [Vendor Defined Widget] wcaps 0xf00000: Mono > Node 0x08 [Audio Input] wcaps 0x10011b: Stereo Amp-In > Amp-In caps: ofs=0x0b, nsteps=0x1f, stepsize=0x05, mute=1 > Amp-In vals: [0x9f 0x9f] > PCM: > rates [0x160]: 44100 48000 96000 > bits [0x6]: 16 20 > formats [0x1]: PCM > Connection: 1 > 0x23 > Node 0x09 [Audio Input] wcaps 0x10011b: Stereo Amp-In > Amp-In caps: ofs=0x0b, nsteps=0x1f, stepsize=0x05, mute=1 > Amp-In vals: [0x9f 0x9f] > PCM: > rates [0x160]: 44100 48000 96000 > bits [0x6]: 16 20 > formats [0x1]: PCM > Connection: 1 > 0x22 > Node 0x0a [Audio Input] wcaps 0x100391: Stereo Digital > PCM: > rates [0x560]: 44100 48000 96000 192000 > bits [0x1e]: 16 20 24 32 > formats [0x1]: PCM > Connection: 1 > 0x1f > Node 0x0b [Audio Mixer] wcaps 0x20010b: Stereo Amp-In > Amp-In caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1 > Amp-In vals: [0x80 0x80] [0x80 0x80] [0x9d 0x9d] [0x80 0x80] [0x9f 0x9f] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] > Connection: 10 > 0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 > Node 0x0c [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out > Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 > Amp-In vals: [0x00 0x00] [0x00 0x00] > Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=0 > Amp-Out vals: [0x1d 0x1d] > Connection: 2 > 0x02 0x0b > Node 0x0d [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out > Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 > Amp-In vals: [0x00 0x00] [0x00 0x00] > Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=0 > Amp-Out vals: [0x1f 0x1f] > Connection: 2 > 0x03 0x0b > Node 0x0e [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out > Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 > Amp-In vals: [0x00 0x00] [0x00 0x00] > Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=0 > Amp-Out vals: [0x1f 0x1f] > Connection: 2 > 0x04 0x0b > Node 0x0f [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out > Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 > Amp-In vals: [0x80 0x80] [0x80 0x80] > Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=0 > Amp-Out vals: [0x00 0x00] > Connection: 2 > 0x05 0x0b > Node 0x10 [Vendor Defined Widget] wcaps 0xf00000: Mono > Node 0x11 [Vendor Defined Widget] wcaps 0xf00000: Mono > Node 0x12 [Vendor Defined Widget] wcaps 0xf00000: Mono > Node 0x13 [Vendor Defined Widget] wcaps 0xf00000: Mono > Node 0x14 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out > Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 > Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] > Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 > Amp-Out vals: [0x00 0x00] > Pincap 0x083e: IN OUT HP Detect > Pin Default 0x01014010: [Jack] Line Out at Ext Rear > Conn = 1/8, Color = Green > Pin-ctls: 0x40: OUT > Connection: 5 > 0x0c* 0x0d 0x0e 0x0f 0x26 > Node 0x15 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out > Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 > Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] > Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 > Amp-Out vals: [0x00 0x00] > Pincap 0x083e: IN OUT HP Detect > Pin Default 0x01011012: [Jack] Line Out at Ext Rear > Conn = 1/8, Color = Black > Pin-ctls: 0x40: OUT > Connection: 5 > 0x0c 0x0d* 0x0e 0x0f 0x26 > Node 0x16 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out > Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 > Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] > Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 > Amp-Out vals: [0x00 0x00] > Pincap 0x0836: IN OUT Detect > Pin Default 0x01016011: [Jack] Line Out at Ext Rear > Conn = 1/8, Color = Orange > Pin-ctls: 0x40: OUT > Connection: 5 > 0x0c 0x0d 0x0e* 0x0f 0x26 > Node 0x17 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out > Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 > Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] > Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 > Amp-Out vals: [0x00 0x00] > Pincap 0x0836: IN OUT Detect > Pin Default 0x01012014: [Jack] Line Out at Ext Rear > Conn = 1/8, Color = Grey > Pin-ctls: 0x40: OUT > Connection: 5 > 0x0c 0x0d 0x0e 0x0f* 0x26 > Node 0x18 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out > Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 > Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] > Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 > Amp-Out vals: [0x00 0x00] > Pincap 0x08373e: IN OUT HP Detect > Pin Default 0x01813040: [Jack] Line In at Ext Rear > Conn = 1/8, Color = Blue > Pin-ctls: 0x40: OUT > Connection: 5 > 0x0c 0x0d 0x0e* 0x0f 0x26 > Node 0x19 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out > Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 > Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] > Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 > Amp-Out vals: [0x80 0x80] > Pincap 0x08373e: IN OUT HP Detect > Pin Default 0x02a19850: [Jack] Mic at Ext Front > Conn = 1/8, Color = Pink > Pin-ctls: 0x24: IN > Connection: 5 > 0x0c* 0x0d 0x0e 0x0f 0x26 > Node 0x1a [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out > Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 > Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] > Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 > Amp-Out vals: [0x00 0x00] > Pincap 0x08373e: IN OUT HP Detect > Pin Default 0x9993014f: [Fixed] Aux at Int ATAPI > Conn = ATAPI, Color = Unknown > Pin-ctls: 0x40: OUT > Connection: 5 > 0x0c 0x0d* 0x0e 0x0f 0x26 > Node 0x1b [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out > Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 > Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] > Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 > Amp-Out vals: [0x00 0x00] > Pincap 0x08373e: IN OUT HP Detect > Pin Default 0x02214020: [Jack] HP Out at Ext Front > Conn = 1/8, Color = Green > Pin-ctls: 0xc0: OUT HP > Connection: 5 > 0x0c* 0x0d 0x0e 0x0f 0x26 > Node 0x1c [Pin Complex] wcaps 0x400001: Stereo > Pincap 0x0820: IN > Pin Default 0x411111f0: [N/A] Speaker at Ext Rear > Conn = 1/8, Color = Black > Pin-ctls: 0x20: IN > Node 0x1d [Pin Complex] wcaps 0x400000: Mono > Pincap 0x0820: IN > Pin Default 0x4005a603: [N/A] Line Out at Ext N/A > Conn = Optical, Color = UNKNOWN > Pin-ctls: 0x20: IN > Node 0x1e [Pin Complex] wcaps 0x400300: Mono Digital > Pincap 0x0810: OUT > Pin Default 0x01451130: [Jack] SPDIF Out at Ext Rear > Conn = Optical, Color = Black > Pin-ctls: 0x40: OUT > Connection: 1 > 0x06 > Node 0x1f [Pin Complex] wcaps 0x400200: Mono Digital > Pincap 0x0820: IN > Pin Default 0x01c59160: [Jack] SPDIF In at Ext Rear > Conn = Optical, Color = Pink > Pin-ctls: 0x20: IN > Node 0x20 [Vendor Defined Widget] wcaps 0xf00040: Mono > Node 0x21 [Vendor Defined Widget] wcaps 0xf00000: Mono > Node 0x22 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In > Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 > Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x80 0x80] [0x00 0x00] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] > Connection: 11 > 0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 0x0b > Node 0x23 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In > Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 > Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x80 0x80] [0x00 0x00] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] > Connection: 11 > 0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 0x0b > Node 0x24 [Vendor Defined Widget] wcaps 0xf00000: Mono > Node 0x25 [Audio Output] wcaps 0x11: Stereo > PCM: > rates [0x560]: 44100 48000 96000 192000 > bits [0xe]: 16 20 24 > formats [0x1]: PCM > Node 0x26 [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out > Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 > Amp-In vals: [0x00 0x00] [0x80 0x80] > Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=0 > Amp-Out vals: [0x00 0x00] > Connection: 2 > 0x25 0x0b > > A second codec sits at /proc/asound/Intel/codec#0. A cat results in: > > Codec: Generic 1095 ID 1392 > Address: 1 > Vendor Id: 0x10951392 > Subsystem Id: 0xffffffff > Revision Id: 0x100000 > No Modem Function Group found > Default PCM: > rates [0x0]: > bits [0x0]: > formats [0x0]: > Default Amp-In caps: N/A > Default Amp-Out caps: N/A > Node 0x02 [Audio Output] wcaps 0x6211: Stereo Digital > PCM: > rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000 > bits [0x1e]: 16 20 24 32 > formats [0x5]: PCM AC3 > Node 0x03 [Pin Complex] wcaps 0x40738d: Stereo Digital Amp-Out > Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 > Amp-Out vals: [0x80 0x80] > Pincap 0x0894: OUT Detect > Pin Default 0x18560010: [Jack] Digital Out at Int HDMI > Conn = Digital, Color = Unknown > Pin-ctls: 0x00: > Connection: 1 > 0x02 > > > > From: tdavis@xxxxxxxxxxxx > > To: fuuss@xxxxxxxxxxx > > Date: Wed, 26 Dec 2007 11:30:28 -0800 > > CC: alsa-devel@xxxxxxxxxxxxxxxx > > Subject: Re: intel-hd on an intel G33 motherboard > > > > Try "model=3stack-6ch". Also, if you look in the > > alsa-driver-1.0.15/alsa-kernel/Documentation/Alsa-Configuration.txt > > file, there are other models you can select for the alc883/888 codec. > > > > Let me know if this works and I'll add your system to the driver. > > > > Tobin > > > > On Wed, 2007-12-26 at 18:42 +0000, De Fuuss wrote: > > > >> Hi, > >> > >> Maybe I'm missing something, but I've failed to get even the slightest > >> noise out of the onboard sound card from a Intel G33 motherboard. I > >> tried the alsa drivers from the alsa-driver-1.0.15 package as well as > >> the the alsa drivers provided by kernel 2.6.23 (built as modules), to > >> no avail. > >> > >> The sound chip is identified as a Intel HDA / Realtek ALC888 on the Intel G33 ICH9 motherboard. > >> > >> After reading some of the documentation from the ALSA site and googling through half the internet I haven't found out yet if this specific sound card is supported by ALSA and if some module options must be passed (such as options snd-intel-hda model=.....). > >> > >> Could somebody be so kind as to point me into the right direction? > >> > >> Thank you. > >> > >> Best regards, > >> > >> Patrick > >> > >> _________________________________________________________________ > >> Express yourself instantly with MSN Messenger! Download today it's FREE! > >> http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/ > >> _______________________________________________ > >> Alsa-devel mailing list > >> Alsa-devel@xxxxxxxxxxxxxxxx > >> http://mailman.alsa-project.org/mailman/listinfo/alsa-devel > > > > -- > > Tobin Davis > > > > > > TONY RANDALL! Is YOUR life a PATIO of FUN?? > > _______________________________________________ > > Alsa-devel mailing list > > Alsa-devel@xxxxxxxxxxxxxxxx > > http://mailman.alsa-project.org/mailman/listinfo/alsa-devel > > _________________________________________________________________ > Express yourself instantly with MSN Messenger! Download today it's FREE! > http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/ > _______________________________________________ > Alsa-devel mailing list > Alsa-devel@xxxxxxxxxxxxxxxx > http://mailman.alsa-project.org/mailman/listinfo/alsa-devel -- Tobin Davis glDisable (GL_BUGS); heh Is that in 1.2? :) _______________________________________________ Alsa-devel mailing list Alsa-devel@xxxxxxxxxxxxxxxx http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
