Hi Samuel, On Fri, 10 Jul 2020 at 07:44, Samuel Holland <samuel@xxxxxxxxxxxx> wrote: > > On 7/4/20 6:38 AM, Clément Péron wrote: > > From: Marcus Cooper <codekipper@xxxxxxxxx> > > > > On the newer SoCs such as the H3 and A64 this is set by default > > to transfer a 0 after each sample in each slot. However the A10 > > and A20 SoCs that this driver was developed on had a default > > setting where it padded the audio gain with zeros. > > > > This isn't a problem while we have only support for 16bit audio > > but with larger sample resolution rates in the pipeline then SEXT > > bits should be cleared so that they also pad at the LSB. Without > > this the audio gets distorted. > > > > Set sign extend sample for all the sunxi generations even if they > > are not affected. This will keep coherency and avoid relying on > > default. > > > > Signed-off-by: Marcus Cooper <codekipper@xxxxxxxxx> > > Signed-off-by: Clément Péron <peron.clem@xxxxxxxxx> > > --- > > sound/soc/sunxi/sun4i-i2s.c | 22 ++++++++++++++++++++++ > > 1 file changed, 22 insertions(+) > > > > diff --git a/sound/soc/sunxi/sun4i-i2s.c b/sound/soc/sunxi/sun4i-i2s.c > > index 8bae97efea30..f78167e152ce 100644 > > --- a/sound/soc/sunxi/sun4i-i2s.c > > +++ b/sound/soc/sunxi/sun4i-i2s.c > > @@ -48,6 +48,9 @@ > > #define SUN4I_I2S_FMT0_FMT_I2S (0 << 0) > > > > #define SUN4I_I2S_FMT1_REG 0x08 > > +#define SUN4I_I2S_FMT1_REG_SEXT_MASK BIT(8) > > +#define SUN4I_I2S_FMT1_REG_SEXT(sext) ((sext) << 8) > > + > > #define SUN4I_I2S_FIFO_TX_REG 0x0c > > #define SUN4I_I2S_FIFO_RX_REG 0x10 > > > > @@ -105,6 +108,9 @@ > > #define SUN8I_I2S_FMT0_BCLK_POLARITY_INVERTED (1 << 7) > > #define SUN8I_I2S_FMT0_BCLK_POLARITY_NORMAL (0 << 7) > > > > +#define SUN8I_I2S_FMT1_REG_SEXT_MASK GENMASK(5, 4) > > +#define SUN8I_I2S_FMT1_REG_SEXT(sext) ((sext) << 4) > > + > > #define SUN8I_I2S_INT_STA_REG 0x0c > > #define SUN8I_I2S_FIFO_TX_REG 0x20 > > > > @@ -663,6 +669,12 @@ static int sun4i_i2s_set_soc_fmt(const struct sun4i_i2s *i2s, > > } > > regmap_update_bits(i2s->regmap, SUN4I_I2S_CTRL_REG, > > SUN4I_I2S_CTRL_MODE_MASK, val); > > + > > + /* Set sign extension to pad out LSB with 0 */ > > + regmap_update_bits(i2s->regmap, SUN4I_I2S_FMT1_REG, > > + SUN4I_I2S_FMT1_REG_SEXT_MASK, > > + SUN4I_I2S_FMT1_REG_SEXT(0)); > > + > > This is just a note; I'm not suggesting a change here: > > This does nothing, because SUN4I_I2S_FMT1_REG only affects PCM mode, which is > not implemented in the driver for the sun4i generation of hardware. PCM mode > requires setting bit 4 of SUN4I_I2S_CTRL_REG, and then configuring > SUN4I_I2S_FMT1_REG instead of SUN4I_I2S_FMT0_REG. Thanks for the catch, So i will drop it for sun4i. Regards, Clement > > Regards, > Samuel
