External HDMI receivers have analog circuitry that needs to be powered-on when exiting standby, and a mechanism to detect PCM v. IEC61937 data. These two steps take time and up to 2-3 seconds of audio may be muted when starting playback. Intel hardware can keep the link active with a 'silent stream', so that the receiver does not go through those two steps when valid audio is transmitted. This mechanism relies on an info packet and preventing the codec from going to D3, which will increase the platform static power consumption. The info packet assumes a basic 2ch stereo, and the silent stream is enabled when connecting a monitor. In case of format changes the detection of PCM v. IEC61937 needs to be re-run. In this case there is no way to avoid the 2-3s mute. The silent stream is enabled with a Kconfig option, as well as a kernel parameter should there be a need to override the build time default. Silent stream is supported in Intel platforms Skylake and beyond. Tested HDMI plug-out plug-in from Intel Cometlake based Chromebook connected to few different monitors. Reviewed-by: Kai Vehmanen <kai.vehmanen@xxxxxxxxxxxxxxx> Signed-off-by: Harsha Priya <harshapriya.n@xxxxxxxxx> Signed-off-by: Emmanuel Jillela <emmanuel.jillela@xxxxxxxxx> --- sound/pci/hda/Kconfig | 16 ++++++++++++++++ sound/pci/hda/patch_hdmi.c | 34 ++++++++++++++++++++++++++++++++++ 2 files changed, 50 insertions(+) diff --git a/sound/pci/hda/Kconfig b/sound/pci/hda/Kconfig index 7ba542e45a3d..8804808410b3 100644 --- a/sound/pci/hda/Kconfig +++ b/sound/pci/hda/Kconfig @@ -232,4 +232,20 @@ config SND_HDA_POWER_SAVE_DEFAULT endif +config SND_HDA_INTEL_HDMI_SILENT_STREAM + bool "Enable Silent Stream always for HDMI" + depends on SND_HDA + help + Intel hardware has a feature called 'silent stream', that + keeps external HDMI receiver's analog circuitry powered on + avoiding 2-3 sec silence during playback start. This mechanism + relies on an info packet and preventing the codec from going to + D3. (increasing the platform static power consumption when a + HDMI receiver is plugged-in). 2-3 sec silence at the playback + start is expected whenever there is format change. (default is + 2 channel format). + Say Y to enable Silent Stream feature. + +endif + endmenu diff --git a/sound/pci/hda/patch_hdmi.c b/sound/pci/hda/patch_hdmi.c index fbd7cc6026d8..52bb81c952af 100644 --- a/sound/pci/hda/patch_hdmi.c +++ b/sound/pci/hda/patch_hdmi.c @@ -42,6 +42,11 @@ static bool enable_acomp = true; module_param(enable_acomp, bool, 0444); MODULE_PARM_DESC(enable_acomp, "Enable audio component binding (default=yes)"); +static bool enable_silent_stream = +IS_ENABLED(CONFIG_SND_HDA_INTEL_HDMI_SILENT_STREAM); +module_param(enable_silent_stream, bool, 0644); +MODULE_PARM_DESC(enable_silent_stream, "Enable Silent Stream for HDMI receivers"); + struct hdmi_spec_per_cvt { hda_nid_t cvt_nid; int assigned; @@ -1634,21 +1639,50 @@ static void hdmi_present_sense_via_verbs(struct hdmi_spec_per_pin *per_pin, snd_hda_power_down_pm(codec); } +static void silent_stream_enable(struct hda_codec *codec, + struct hdmi_spec_per_pin *per_pin) +{ + codec_dbg(codec, "hdmi: Enabling silent stream for NID %d\n", + per_pin->pin_nid); + + mutex_lock(&per_pin->lock); + if (!per_pin->channels) + per_pin->channels = 2; + hdmi_setup_audio_infoframe(codec, per_pin, per_pin->non_pcm); + mutex_unlock(&per_pin->lock); +} + /* update ELD and jack state via audio component */ static void sync_eld_via_acomp(struct hda_codec *codec, struct hdmi_spec_per_pin *per_pin) { struct hdmi_spec *spec = codec->spec; struct hdmi_eld *eld = &spec->temp_eld; + bool monitor_prev, monitor_next; mutex_lock(&per_pin->lock); eld->monitor_present = false; + monitor_prev = per_pin->sink_eld.monitor_present; eld->eld_size = snd_hdac_acomp_get_eld(&codec->core, per_pin->pin_nid, per_pin->dev_id, &eld->monitor_present, eld->eld_buffer, ELD_MAX_SIZE); eld->eld_valid = (eld->eld_size > 0); update_eld(codec, per_pin, eld, 0); + monitor_next = per_pin->sink_eld.monitor_present; mutex_unlock(&per_pin->lock); + + /* + * Power-up will call hdmi_present_sense, so the PM calls + * have to be done without mutex held. + */ + + if (enable_silent_stream) { + if (!monitor_prev && monitor_next) { + snd_hda_power_up_pm(codec); + silent_stream_enable(codec, per_pin); + } else if (monitor_prev && !monitor_next) + snd_hda_power_down_pm(codec); + } } static void hdmi_present_sense(struct hdmi_spec_per_pin *per_pin, int repoll) -- 2.17.1