* Peter Ujfalusi <peter.ujfalusi@xxxxxx> [200218 15:16]:
> On 18/02/2020 1.23, Tony Lindgren wrote:
> > * Peter Ujfalusi <peter.ujfalusi@xxxxxx> [200214 13:30]:
> >> Hi Tony,
> >>
> >> On 12/02/2020 16.46, Tony Lindgren wrote:
> >>> * Peter Ujfalusi <peter.ujfalusi@xxxxxx> [200212 09:18]:
> >>>> On 11/02/2020 20.10, Tony Lindgren wrote:
> >>>>> +static int cpcap_voice_set_tdm_slot(struct snd_soc_dai *dai,
> >>>>> + unsigned int tx_mask, unsigned int rx_mask,
> >>>>> + int slots, int slot_width)
> >>>>> +{
> >>>>> + struct snd_soc_component *component = dai->component;
> >>>>> + struct cpcap_audio *cpcap = snd_soc_component_get_drvdata(component);
> >>>>> + int err, ts_mask, mask;
> >>>>> + bool voice_call;
> >>>>> +
> >>>>> + /*
> >>>>> + * Primitive test for voice call, probably needs more checks
> >>>>> + * later on for 16-bit calls detected, Bluetooth headset etc.
> >>>>> + */
> >>>>> + if (tx_mask == 0 && rx_mask == 1 && slot_width == 8)
> >>>>> + voice_call = true;
> >>>>> + else
> >>>>> + voice_call = false;
> >>>>
> >>>> You only have voice call if only rx slot0 is in use?
> >>>
> >>> Yeah so it seems. Then there's the modem to wlcore bluetooth path that
> >>> I have not looked at. But presumably that's again just configuring some
> >>> tdm slot on the PMIC.
> >>>
> >>>> If you record mono on the voice DAI, then rx_mask is also 1, no?
> >>>
> >>> It is above :) But maybe I don't follow what you're asking here
> >>
> >> If you arecrod -Dvoice_pcm -c1 -fS8 > /dev/null
> >> then it is reasonable that the machine driver will set rx_mask = 1
> >>
> >>> and maybe you have some better check in mind.
> >>
> >> Not sure, but relying on set_tdm_slots to decide if we are in a call
> >> case does not sound right.
> >
> > OK yeah seems at least bluetooth would need to be also handled
> > in the set_tdm_slots.
>
> set_tdm_slots() is for setting how the TDM slots supposed to be used by
> the component and not really for things to configure different operating
> modes.
>
> If you hardwire things in set_tdm_slots() for the droid4 then how the
> codec driver can be reused in other setups?
Right, I'm all go for better solutions :)
> >>>> You will also set the sampling rate for voice in
> >>>> cpcap_voice_hw_params(), but that is for normal playback/capture, right?
> >>>
> >>> Yeah so normal playback/capture is already working with cpcap codec driver
> >>> with mainline Linux. The voice call needs to set rate to 8000.
> >>
> >> But if you have a voice call initiated should not the rate be set by the
> >> set_sysclk()?
> >
> > Hmm does set_sysclk called from modem codec know that cpcap codec
> > is the clock master based on bitclock-master and set the rate
> > for cpcap codec?
>
> Neither component should call set_sysclk, set_tdm_slots. The machine
> driver should as it is the only one who know how things are wired...
OK, but so what's the machine driver part in this case?
Regards,
Tony
