Hi Takashi.
When the ad1848/cs2431 is first being initialized, auto-calibration may not
be set causing a timeout waiting for it in snd_ad1848/cs4231_mce_down().
This has no dire consequences other than an alarming printk, but since what
we need to wait for is for the calibration to _finish_, let's just check for
that instead.
The early chips need a slight delay (as commented -- 5 sample periods) to be
sure that _if_ calibration is going to happen, it has started when we check
While the CS4231A datasheet implies it'll happen immediately on downing MCE,
some testing is showing that there's a window there as well, so just do the
delay everywhere.
Thanks to Krysztof Helt for pinpointing this problem.
Signed-off-by: Rene Herman <rene.herman@xxxxxxxxx>
Rene.
diff --git a/sound/isa/ad1848/ad1848_lib.c b/sound/isa/ad1848/ad1848_lib.c
index 8094282..dcd4435 100644
--- a/sound/isa/ad1848/ad1848_lib.c
+++ b/sound/isa/ad1848/ad1848_lib.c
@@ -227,16 +227,15 @@ static void snd_ad1848_mce_down(struct snd_ad1848 *chip)
spin_unlock_irqrestore(&chip->reg_lock, flags);
return;
}
- /* calibration process */
- for (timeout = 500; timeout > 0 && (snd_ad1848_in(chip, AD1848_TEST_INIT) & AD1848_CALIB_IN_PROGRESS) == 0; timeout--);
- if ((snd_ad1848_in(chip, AD1848_TEST_INIT) & AD1848_CALIB_IN_PROGRESS) == 0) {
- snd_printd("mce_down - auto calibration time out (1)\n");
- spin_unlock_irqrestore(&chip->reg_lock, flags);
- return;
- }
+ /*
+ * Wait for (possible -- during init auto-calibration may not be set)
+ * calibration process to start. Needs upto 5 sample periods on AD1848
+ * which at the slowest possible rate of 5.5125 kHz means 907 us.
+ */
+ msleep(1);
#if 0
- printk("(2) timeout = %i, jiffies = %li\n", timeout, jiffies);
+ printk("(2) jiffies = %li\n", jiffies);
#endif
time = HZ / 4;
while (snd_ad1848_in(chip, AD1848_TEST_INIT) & AD1848_CALIB_IN_PROGRESS) {
diff --git a/sound/isa/cs423x/cs4231_lib.c b/sound/isa/cs423x/cs4231_lib.c
index 914d77b..9e8e0f1 100644
--- a/sound/isa/cs423x/cs4231_lib.c
+++ b/sound/isa/cs423x/cs4231_lib.c
@@ -346,16 +346,14 @@ void snd_cs4231_mce_down(struct snd_cs4231 *chip)
}
snd_cs4231_busy_wait(chip);
- /* calibration process */
-
- for (timeout = 500; timeout > 0 && (snd_cs4231_in(chip, CS4231_TEST_INIT) & CS4231_CALIB_IN_PROGRESS) == 0; timeout--)
- udelay(10);
- if ((snd_cs4231_in(chip, CS4231_TEST_INIT) & CS4231_CALIB_IN_PROGRESS) == 0) {
- snd_printd("cs4231_mce_down - auto calibration time out (1)\n");
- return;
- }
+ /*
+ * Wait for (possible -- during init auto-calibration may not be set)
+ * calibration process to start. Needs upto 5 sample periods on AD1848
+ * which at the slowest possible rate of 5.5125 kHz means 907 us.
+ */
+ msleep(1);
#if 0
- printk("(2) timeout = %i, jiffies = %li\n", timeout, jiffies);
+ printk("(2) jiffies = %li\n", jiffies);
#endif
/* in 10 ms increments, check condition, up to 250 ms */
timeout = 25;
_______________________________________________
Alsa-devel mailing list
Alsa-devel@xxxxxxxxxxxxxxxx
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
