On Wed, May 8, 2013 at 6:59 PM, Dave Anderson <anderson@xxxxxxxxxx> wrote: > > > > ----- Original Message ----- >> On Wed, May 8, 2013 at 11:23 AM, Anand Raj Manickam <anandrm@xxxxxxxxx> >> wrote: >> >> Hi , >> >> Sorry about re posting this as i did not find solution ... >> >> >> >> I m facing a issue where on >> >> >> >> #crash /data/linux-2.6.30.8/vmlinux /proc/vmcore >> > >> > Do yourself a favor and copy /proc/vmcore to somewhere on disk. Then >> > reboot the system into the original kernel, and run crash on the saved >> > vmcore. I've never seen crash run on a /proc/vmcore file from the >> > secondary kernel. >> > >> > Also, after rebooting the the original kernel, please confirm that >> > crash runs OK on the live system. >> > >> > >> >> crash 6.1.6 >> >> Copyright (C) 2002-2013 Red Hat, Inc. >> >> Copyright (C) 2004, 2005, 2006, 2010 IBM Corporation >> >> Copyright (C) 1999-2006 Hewlett-Packard Co >> >> Copyright (C) 2005, 2006, 2011, 2012 Fujitsu Limited >> >> Copyright (C) 2006, 2007 VA Linux Systems Japan K.K. >> >> Copyright (C) 2005, 2011 NEC Corporation >> >> Copyright (C) 1999, 2002, 2007 Silicon Graphics, Inc. >> >> Copyright (C) 1999, 2000, 2001, 2002 Mission Critical Linux, Inc. >> >> This program is free software, covered by the GNU General Public License, >> >> and you are welcome to change it and/or distribute copies of it under >> >> certain conditions. Enter "help copying" to see the conditions. >> >> This program has absolutely no warranty. Enter "help warranty" for >> >> details. >> >> >> >> GNU gdb (GDB) 7.3.1 >> >> Copyright (C) 2011 Free Software Foundation, Inc. >> >> License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html> >> >> This is free software: you are free to change and redistribute it. >> >> There is NO WARRANTY, to the extent permitted by law. Type "show copying" >> >> and "show warranty" for details. >> >> This GDB was configured as "i686-pc-linux-gnu"... >> >> >> >> crash: read error: kernel virtual address: c127a9c8 type: "cpu_possible_mask" >> > >> > Please show the full output of "crash -d8 vmlinux vmcore". >> >> After rebooting to the primary / live kernel >> >> I have attached the output for "crash -d8 vmlinux /data/vmcore" in d8.txt > > Looking at the ELF header data in the debug output, your configuration > does require special handling. X86 kernels are typically not configured > with CONFIG_PHYSICAL_START larger than CONFIG_PHYSICAL_ALIGN, because > when that is done, the vmlinux unity-mapped symbol values do not match > their relocated values when the kernel is loaded. This entry in the > crash.changelog describes the situation: > > http://people.redhat.com/anderson/crash.changelog.html#4_0_4_5 > > 4.0-4.5 - Addresses FC7/upstream x86 kernels that have been configured such > that the vmlinux symbol values do not match their relocated values > when loaded. If CONFIG_PHYSICAL_START contains a value that is > greater then CONFIG_PHYSICAL_ALIGN, then this mismatch occurs. > Since the crash utility and its embedded gdb have always expected > that the compiled-in kernel symbol addresses are "real", the virtual > to physical translation fails, leading to an initialization-time > failure with the message: "crash: vmlinux and /dev/crash do not > match!" (/dev/mem or the dumpfile name may replace /dev/crash). > To deal with this issue, there are several alternatives: > > 1) Configure the kernel with CONFIG_PHYSICAL_START less than > or equal to CONFIG_PHYSICAL_ALIGN. Having done that, there > is no problem; the resultant vmlinux file will be loaded at > the address for which it was compiled, which has always > been the case. > 2) Since /proc/kallsyms uses the same format as a System.map file, > and since it reflects the relocated symbol addresses, it > can be placed on the crash command line as if it were > a System.map file. (Note that the System.map file created > by these relocated kernels contains the same "wrong" symbol > values as the vmlinux file from which it was created.) > 3) On a live system that has /proc/kallsyms (i.e., the kernel was > configured with CONFIG_KALLSYMS), this version of the crash > utility will replace/patch the vmlinux symbol values with those > seen in /proc/kallsyms. The relocation value will be displayed > as a WARNING message during initialization. > 4) On a dumpfile, the relocation will not be performed automatically > as on a live system. It will require the addition of the > /proc/kallsyms on the command line, or if run on a different > host, a copy of the crashed system's /proc/kallsyms may be > used. > 5) Alternatively on a dumpfile, a new command line option has been > created to specify the relocation amount. For example, if a > kernel was configured with a CONFIG_PHYSICAL_START value of 16MB > and a CONFIG_PHYSICAL_ALIGN of 4MB, that results in a relocation > of 12MB. To specify that, enter "crash --reloc=12m ..." on the > command line. (Recall that if crash is run on the live system, > a WARNING message will specify the relocation amount.) > > Using /proc/kallsyms or a --reloc=[size] as a command line argument > is similar to using a System.map file, in that it results in the loss > of the use of line number debug data. (anderson@xxxxxxxxxx) > > ... > >>> My current config for >>> >>> CONFIG_PHYSICAL_START=0x1000000 >>> CONFIG_RELOCATABLE=y >>> CONFIG_PHYSICAL_ALIGN=0x400000 >>> >>> The /proc/kallsyms is diffrent between the System Kernel and Debug Kernel. >>> On the System Kernel it starts from 0x400000 .On the Debug kernel it >>> starts from 0x1000000. > > So your configuration exactly matches paragraph 5) above, you should > be able to come up OK by entering either: > > $ crash vmlinux vmcore --reloc=12m This did the trick :-) Great !! and Thanks Dave. > > or > > $ crash vmlinux vmcore /proc/kallsyms > > where the /proc/kallsyms is from the *primary* kernel, so option #2 > will *not* work when running from the secondary kernel. > > You didn't show any output of a live crash session (while running > on the primary kernel), but I believe it should work without using > the /proc/kallsyms as an argument or using --reloc=12m option. There > was a further fix for these configurations for running on live systems: > > http://people.redhat.com/anderson/crash.changelog.html#5_1_4 > > 5.1.4 - Fix for RT kernels in which the schedule() function has become a > ... [ cut] ... > > - Fix for running against live x86 kernels that were configured with > CONFIG_PHYSICAL_START containing a value that is greater than its > CONFIG_PHYSICAL_ALIGN value, and where the first symbol listed by > /proc/kallsyms is not "_text". Without the patch, the crash session > fails during invocation with the error message "crash: vmlinux and > /dev/mem do not match!" (or "/dev/crash" if applicable). As a work- > around, "/proc/kallsyms" can be entered on the command line, or the > "--reloc=<size>" option could be used, but the fix obviates that > requirement for live systems. It should be noted that dumpfiles of > kernels configured that way still do require that "/proc/kallsyms", > or a copy of it, or alternatively the "--reloc=<size>" option, to > be entered on the command line, as detailed in this changelog entry: > http://people.redhat.com/anderson/crash.changelog.html#4_0_4_5 > (anderson@xxxxxxxxxx) > > So on the live system on the primary kernel, I believe this should just work: > > $ crash vmlinux > > Normally you don't even need to put the vmlinux file on the command line for > running on the live system because it will be "found" automatically unless > you've put it in some non-standard location. > > Dave > -- Crash-utility mailing list Crash-utility@xxxxxxxxxx https://www.redhat.com/mailman/listinfo/crash-utility