[PATCH v2 09/14] ASoC: dt-bindings: qcom,wsa881x: extend description to analog mode

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]



WSA881X also supports analog mode when device is configured via i2c
only. Document it, add properties, new compatibles and example.

While at this, also adjust quotes.

Cc: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx>
Signed-off-by: Alexey Klimov <alexey.klimov@xxxxxxxxxx>
---
 .../bindings/sound/qcom,wsa881x.yaml          | 75 +++++++++++++++++--
 1 file changed, 67 insertions(+), 8 deletions(-)

diff --git a/Documentation/devicetree/bindings/sound/qcom,wsa881x.yaml b/Documentation/devicetree/bindings/sound/qcom,wsa881x.yaml
index ac03672ebf6d..e482d9dc0de2 100644
--- a/Documentation/devicetree/bindings/sound/qcom,wsa881x.yaml
+++ b/Documentation/devicetree/bindings/sound/qcom,wsa881x.yaml
@@ -12,15 +12,17 @@ maintainers:
 description: |
   WSA8810 is a class-D smart speaker amplifier and WSA8815
   is a high-output power class-D smart speaker amplifier.
-  Their primary operating mode uses a SoundWire digital audio
-  interface. This binding is for SoundWire interface.
-
-allOf:
-  - $ref: dai-common.yaml#
+  This family of amplifiers support two operating modes:
+  SoundWire digital audio interface which is a primary mode
+  and analog mode when device is configured via i2c only.
+  This binding describes both modes.
 
 properties:
   compatible:
-    const: sdw10217201000
+    enum:
+      - qcom,wsa8810
+      - qcom,wsa8815
+      - sdw10217201000
 
   reg:
     maxItems: 1
@@ -35,17 +37,60 @@ properties:
   '#sound-dai-cells':
     const: 0
 
+  clocks:
+    maxItems: 1
+
+  mclk-gpios:
+    description: GPIO spec for mclk
+    maxItems: 1
+
 required:
   - compatible
   - reg
   - powerdown-gpios
-  - "#thermal-sensor-cells"
-  - "#sound-dai-cells"
+  - '#thermal-sensor-cells'
+  - '#sound-dai-cells'
+
+allOf:
+  - $ref: dai-common.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,wsa8810
+            const: qcom,wsa8815
+    then:
+      properties:
+        reg:
+          description:
+            In case of analog mode this should be I2C address of the digital
+            part of the device. The I2C address of analog part of an amplifier
+            is expected to be located at the fixed offset.
+          maxItems: 1
+          items:
+            minimum: 0x0e
+            maximum: 0x0f
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,wsa8810
+            const: qcom,wsa8815
+    then:
+      required:
+        - clocks
+        - mclk-gpios
 
 unevaluatedProperties: false
 
 examples:
   - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/sound/qcom,q6afe.h>
+
     soundwire@c2d0000 {
         #address-cells = <2>;
         #size-cells = <0>;
@@ -68,4 +113,18 @@ examples:
         };
     };
 
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        amplifier@e {
+            compatible = "qcom,wsa8810";
+            reg = <0x0e>;
+            clocks = <&q6afecc LPASS_CLK_ID_MCLK_3 LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+            powerdown-gpios = <&lpass_tlmm 16 GPIO_ACTIVE_LOW>;
+            mclk-gpios = <&lpass_tlmm 18 GPIO_ACTIVE_HIGH>;
+            #sound-dai-cells = <0>;
+            #thermal-sensor-cells = <0>;
+       };
+    };
 ...
-- 
2.45.2





[Index of Archives]     [Pulseaudio]     [Linux Audio Users]     [ALSA Devel]     [Fedora Desktop]     [Fedora SELinux]     [Big List of Linux Books]     [Yosemite News]     [KDE Users]

  Powered by Linux