On Sun, 20 Oct 2024 21:30:51 +1300
Ryan Walklin <ryan@xxxxxxxxxxxxx> wrote:
Hi,
> Allwinner has previously released a H616 audio driver which also
> provides sigma-delta modulation for the audio PLL clocks. This approach
> is used in other Allwinner SoCs, including the H3 and A64.
>
> The manual-provided clock values are:
> PLL_AUDIO(hs) = 24 MHz*N/M1
> PLL_AUDIO(4X) = 24 MHz*N/M0/M1/P
> PLL_AUDIO(2X) = 24 MHz*N/M0/M1/P/2
> PLL_AUDIO(1X) = 24 MHz*N/M0/M1/P/4
>
> A fixed post-divider of 2 is used to account for a fixed M0 divider of
> 2 (taken from the vendor BSP driver).
The real reason seems to be that our existing macros and struct cannot
model those extra dividers, and using M0=2 gives better results, so we
fix that in the probe routine and account for that using the fixed
post-div.
> Using SDM allows correction of the PLL_AUDIO_(4,2,1)X clock fixed
> dividers to the datasheet-specified values of 1/2/4 respectively.
As mentioned below, SDM has nothing to do with those simple dividers
clocks, it's just there to reach the "odd" base audio frequency more
accurately.
>
> Add SDM to the H616 clock control unit driver.
>
> Signed-off-by: Ryan Walklin <ryan@xxxxxxxxxxxxx>
>
> ---
> Changelog v1..v2:
> - Add fixed_post_div to high-speed audio clock to correct M0 value to 1 (ie divide by 2) based on manual
> - Correct PLL_AUDIO_(4/2/1)X clocks to manual-provided values
> - Add/correct inline comments for the above.
> - add CCU_FEATURE_FIXED_POSTDIV to pll_audio_hs_clk.common.features
> ---
> drivers/clk/sunxi-ng/ccu-sun50i-h616.c | 44 ++++++++++++++++----------
> 1 file changed, 28 insertions(+), 16 deletions(-)
>
> diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h616.c b/drivers/clk/sunxi-ng/ccu-sun50i-h616.c
> index 6c7623d4c59ea..42feaaf5a59c6 100644
> --- a/drivers/clk/sunxi-ng/ccu-sun50i-h616.c
> +++ b/drivers/clk/sunxi-ng/ccu-sun50i-h616.c
> @@ -215,20 +215,28 @@ static struct ccu_nkmp pll_de_clk = {
> },
> };
>
> -/*
> - * TODO: Determine SDM settings for the audio PLL. The manual suggests
> - * PLL_FACTOR_N=16, PLL_POST_DIV_P=2, OUTPUT_DIV=2, pattern=0xe000c49b
> - * for 24.576 MHz, and PLL_FACTOR_N=22, PLL_POST_DIV_P=3, OUTPUT_DIV=2,
> - * pattern=0xe001288c for 22.5792 MHz.
> - * This clashes with our fixed PLL_POST_DIV_P.
> +/*
> + * Sigma-delta modulation settings table obtained from the vendor SDK driver.
> + * There are additional M0 and M1 divider bits not modelled here, so forced to
> + * fixed values in the probe routine.
> */
> +static struct ccu_sdm_setting pll_audio_sdm_table[] = {
> + { .rate = 90316800, .pattern = 0xc001288d, .m = 3, .n = 22 },
> + { .rate = 98304000, .pattern = 0xc001eb85, .m = 5, .n = 40 },
It's a bit strange to see odd dividers here, since the manual "warns"
against this, because it's causing a non-50% duty cycle. But apparently
the audio codec is fine with this (given it works)? Or does this apply
to the product of all the dividers (m * m0 * m1), so our m0=2 fixes
that?
And for the records, the numbers calculate like this (with SDM):
rate = 24MHz * (n + pattern[16:0] / 2^17) / m / m0 / m1
which gives 90316802 Hz and 98303997 Hz with those numbers,
respectively.
> +};
> +
> #define SUN50I_H616_PLL_AUDIO_REG 0x078
> static struct ccu_nm pll_audio_hs_clk = {
> .enable = BIT(31),
> .lock = BIT(28),
> .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
> - .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
> + .m = _SUNXI_CCU_DIV(16, 6),
> + .sdm = _SUNXI_CCU_SDM(pll_audio_sdm_table,
> + BIT(24), 0x178, BIT(31)),
> + .fixed_post_div = 2,
> .common = {
> + .features = CCU_FEATURE_FIXED_POSTDIV |
> + CCU_FEATURE_SIGMA_DELTA_MOD,
> .reg = 0x078,
> .hw.init = CLK_HW_INIT("pll-audio-hs", "osc24M",
> &ccu_nm_ops,
> @@ -701,18 +709,20 @@ static const struct clk_hw *clk_parent_pll_audio[] = {
> };
>
> /*
> - * The divider of pll-audio is fixed to 24 for now, so 24576000 and 22579200
> - * rates can be set exactly in conjunction with sigma-delta modulation.
> + * The PLL_AUDIO_4X clock defaults to 24.5714 MHz according to the manual, with
The manual says that PLL_AUDIO_1X defaults to 24.5714 MHz (24.576,
really?), so PLL_AUDIO_4X (the actual PLL output) should be four times
that.
> + * a final divider of 1. The 2X and 1X clocks use 2 and 4 respectively. The 1x
> + * clock is set to either 24576000 or 22579200 for 48Khz and 44.1Khz (and
> + * multiples) in conjunction with sigma-delta modulation.
That last part sounds a bit vague, what about:
" ... (and multiples). The Sigma-delta modulation bits allow providing a
fractional-N divider in the PLL, to help reaching those specific
frequencies with less error."
But then again this probably belongs more to the PLL_AUDIO_HS clock
comment above? Since this here is just to model the simple divider
clocks.
Anyway, the technical bits seem to add up, and that's what I came up
with in my experiments as well. But there are better combinations of N,
fractional N, and M to reach the target frequency with less error, and
M is also even in those cases. This could be a later optimisation,
though.
Cheers,
Andre
> */
> static CLK_FIXED_FACTOR_HWS(pll_audio_1x_clk, "pll-audio-1x",
> clk_parent_pll_audio,
> - 96, 1, CLK_SET_RATE_PARENT);
> + 4, 1, CLK_SET_RATE_PARENT);
> static CLK_FIXED_FACTOR_HWS(pll_audio_2x_clk, "pll-audio-2x",
> clk_parent_pll_audio,
> - 48, 1, CLK_SET_RATE_PARENT);
> + 2, 1, CLK_SET_RATE_PARENT);
> static CLK_FIXED_FACTOR_HWS(pll_audio_4x_clk, "pll-audio-4x",
> clk_parent_pll_audio,
> - 24, 1, CLK_SET_RATE_PARENT);
> + 1, 1, CLK_SET_RATE_PARENT);
>
> static const struct clk_hw *pll_periph0_parents[] = {
> &pll_periph0_clk.common.hw
> @@ -1162,12 +1172,14 @@ static int sun50i_h616_ccu_probe(struct platform_device *pdev)
> }
>
> /*
> - * Force the post-divider of pll-audio to 12 and the output divider
> - * of it to 2, so 24576000 and 22579200 rates can be set exactly.
> + * Set the output-divider for the pll-audio clocks (M0) to 2 and the
> + * input divider (M1) to 1 as recommended by the manual when using
> + * SDM.
> */
> val = readl(reg + SUN50I_H616_PLL_AUDIO_REG);
> - val &= ~(GENMASK(21, 16) | BIT(0));
> - writel(val | (11 << 16) | BIT(0), reg + SUN50I_H616_PLL_AUDIO_REG);
> + val &= ~BIT(1);
> + val |= BIT(0);
> + writel(val, reg + SUN50I_H616_PLL_AUDIO_REG);
>
> /*
> * First clock parent (osc32K) is unusable for CEC. But since there
[Index of Archives]
[Pulseaudio]
[Linux Audio Users]
[ALSA Devel]
[Fedora Desktop]
[Fedora SELinux]
[Big List of Linux Books]
[Yosemite News]
[KDE Users]
