Re: [RFC PATCH v1] ASoC: wm8904: enable fll with fixed mclk

[Charles Keepax <ckeepax@xxxxxxxxxxxxxxxxxxxxx>]

On Fri, Mar 08, 2024 at 04:58:31PM +0100, Andrejs Cainikovs wrote:
> From: Andrejs Cainikovs <andrejs.cainikovs@xxxxxxxxxxx>
> 
> Dear all,
> 
> This is an attempt to change wm8904 for a scenario when reference clock
> supposed to be fixed to a particular frequency, but is not configured as
> a fixed-clock. While this change is working fine, I'm struggling to
> finalize it, not being able to find a proper solution of adding a check
> whether we want to use fixed MCLK with codec's FLL or not. I could, of
> course, introduce a new device tree property, but do not feel this would
> be a proper way forward. Hence, I'm sending out this RFC patch to gather
> your valuable feedback.
> 
> DUT: Dahlia carrier board with Verdin TI AM62 SOM.
> Audio card configuration can be found in ti/k3-am62-verdin-dahlia.dtsi.

At some point one really starts to question if this is really a
"simple card" any more.

> On systems with a fixed reference clock output rate it
> is impossible to use this clock for all audio frequencies.
> 
> Following is an example of playing a 44100Hz audio on a system
> with a fixed 25MHz reference clock applied to wm8904 codec,
> in combination with simple-audio-card without mclk-fs:
> 
> [   27.013564] wm8904 1-001a: Target BCLK is 1411200Hz
> [   27.013601] wm8904 1-001a: Using 25000000Hz MCLK
> [   27.013611] wm8904 1-001a: CLK_SYS is 12500000Hz
> [   27.013654] wm8904 1-001a: Selected CLK_SYS_RATIO of 256
> [   27.013663] wm8904 1-001a: Selected SAMPLE_RATE of 44100Hz
> [   27.013671] wm8904 1-001a: Selected BCLK_DIV of 80 for 1562500Hz BCLK
> [   27.013680] wm8904 1-001a: LRCLK_RATE is 35
> 
> This leads to a distorted sound and this configuration is unusable.
> 
> On the other hand, configuring simple-audio-card with mclk-fs will
> force the system to change MCLK frequency, which supposed to be fixed.
> 
> This change forces to use wm8904 FLL while keeping SoC's MCLK
> frequency intact:
> 
> [  234.108149] wm8904 1-001a: Target BCLK is 1411200Hz
> [  234.108304] wm8904 1-001a: Using 0Hz FLL clock
> [  234.108722] wm8904 1-001a: FLL configured for 25000000Hz->1411200Hz
> [  234.108794] wm8904 1-001a: CLK_SYS is 1411200Hz
> [  234.108835] wm8904 1-001a: Selected CLK_SYS_RATIO of 64
> [  234.108875] wm8904 1-001a: Selected SAMPLE_RATE of 44100Hz
> [  234.108913] wm8904 1-001a: Selected BCLK_DIV of 10 for 1411200Hz BCLK
> [  234.108955] wm8904 1-001a: LRCLK_RATE is 32
> 

Hmm... the driver already provides an option to automatically
configure the clock. Is the issue here that in your fail case the
machine driver never calls wm8904_set_sysclk? Or if it does call
it, when and what parameters is it passing?

Thanks,
Charles