From: Chen-Yu Tsai <wens@xxxxxxxx>
The DMA controllers found on the H616 and H618 are the same as the one
found on the A100. The only difference is the DMA endpoint (DRQ) layout.
Add a device node for it, and add DMA channels for existing peripherals.
Signed-off-by: Chen-Yu Tsai <wens@xxxxxxxx>
---
Changes since v1:
- Fall back to A100 instead of H6
- Add DMA channels for r_i2c
.../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 41 +++++++++++++++++++
1 file changed, 41 insertions(+)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
index d549d277d972..885809137b9d 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
@@ -133,6 +133,19 @@ ccu: clock@3001000 {
#reset-cells = <1>;
};
+ dma: dma-controller@3002000 {
+ compatible = "allwinner,sun50i-h616-dma",
+ "allwinner,sun50i-a100-dma";
+ reg = <0x03002000 0x1000>;
+ interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DMA>, <&ccu CLK_MBUS_DMA>;
+ clock-names = "bus", "mbus";
+ dma-channels = <16>;
+ dma-requests = <49>;
+ resets = <&ccu RST_BUS_DMA>;
+ #dma-cells = <1>;
+ };
+
sid: efuse@3006000 {
compatible = "allwinner,sun50i-h616-sid", "allwinner,sun50i-a64-sid";
reg = <0x03006000 0x1000>;
@@ -339,6 +352,8 @@ uart0: serial@5000000 {
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu CLK_BUS_UART0>;
+ dmas = <&dma 14>, <&dma 14>;
+ dma-names = "tx", "rx";
resets = <&ccu RST_BUS_UART0>;
status = "disabled";
};
@@ -350,6 +365,8 @@ uart1: serial@5000400 {
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu CLK_BUS_UART1>;
+ dmas = <&dma 15>, <&dma 15>;
+ dma-names = "tx", "rx";
resets = <&ccu RST_BUS_UART1>;
status = "disabled";
};
@@ -361,6 +378,8 @@ uart2: serial@5000800 {
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu CLK_BUS_UART2>;
+ dmas = <&dma 16>, <&dma 16>;
+ dma-names = "tx", "rx";
resets = <&ccu RST_BUS_UART2>;
status = "disabled";
};
@@ -372,6 +391,8 @@ uart3: serial@5000c00 {
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu CLK_BUS_UART3>;
+ dmas = <&dma 17>, <&dma 17>;
+ dma-names = "tx", "rx";
resets = <&ccu RST_BUS_UART3>;
status = "disabled";
};
@@ -383,6 +404,8 @@ uart4: serial@5001000 {
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu CLK_BUS_UART4>;
+ dmas = <&dma 18>, <&dma 18>;
+ dma-names = "tx", "rx";
resets = <&ccu RST_BUS_UART4>;
status = "disabled";
};
@@ -394,6 +417,8 @@ uart5: serial@5001400 {
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu CLK_BUS_UART5>;
+ dmas = <&dma 19>, <&dma 19>;
+ dma-names = "tx", "rx";
resets = <&ccu RST_BUS_UART5>;
status = "disabled";
};
@@ -405,6 +430,8 @@ i2c0: i2c@5002000 {
reg = <0x05002000 0x400>;
interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_I2C0>;
+ dmas = <&dma 43>, <&dma 43>;
+ dma-names = "rx", "tx";
resets = <&ccu RST_BUS_I2C0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins>;
@@ -420,6 +447,8 @@ i2c1: i2c@5002400 {
reg = <0x05002400 0x400>;
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_I2C1>;
+ dmas = <&dma 44>, <&dma 44>;
+ dma-names = "rx", "tx";
resets = <&ccu RST_BUS_I2C1>;
status = "disabled";
#address-cells = <1>;
@@ -433,6 +462,8 @@ i2c2: i2c@5002800 {
reg = <0x05002800 0x400>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_I2C2>;
+ dmas = <&dma 45>, <&dma 45>;
+ dma-names = "rx", "tx";
resets = <&ccu RST_BUS_I2C2>;
status = "disabled";
#address-cells = <1>;
@@ -446,6 +477,8 @@ i2c3: i2c@5002c00 {
reg = <0x05002c00 0x400>;
interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_I2C3>;
+ dmas = <&dma 46>, <&dma 46>;
+ dma-names = "rx", "tx";
resets = <&ccu RST_BUS_I2C3>;
status = "disabled";
#address-cells = <1>;
@@ -459,6 +492,8 @@ i2c4: i2c@5003000 {
reg = <0x05003000 0x400>;
interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_I2C4>;
+ dmas = <&dma 47>, <&dma 47>;
+ dma-names = "rx", "tx";
resets = <&ccu RST_BUS_I2C4>;
status = "disabled";
#address-cells = <1>;
@@ -472,6 +507,8 @@ spi0: spi@5010000 {
interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
clock-names = "ahb", "mod";
+ dmas = <&dma 22>, <&dma 22>;
+ dma-names = "rx", "tx";
resets = <&ccu RST_BUS_SPI0>;
status = "disabled";
#address-cells = <1>;
@@ -485,6 +522,8 @@ spi1: spi@5011000 {
interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
clock-names = "ahb", "mod";
+ dmas = <&dma 23>, <&dma 23>;
+ dma-names = "rx", "tx";
resets = <&ccu RST_BUS_SPI1>;
status = "disabled";
#address-cells = <1>;
@@ -734,6 +773,8 @@ r_i2c: i2c@7081400 {
reg = <0x07081400 0x400>;
interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&r_ccu CLK_R_APB2_I2C>;
+ dmas = <&dma 48>, <&dma 48>;
+ dma-names = "rx", "tx";
resets = <&r_ccu RST_R_APB2_I2C>;
status = "disabled";
#address-cells = <1>;
--
2.39.2
[Index of Archives]
[Pulseaudio]
[Linux Audio Users]
[ALSA Devel]
[Fedora Desktop]
[Fedora SELinux]
[Big List of Linux Books]
[Yosemite News]
[KDE Users]
